Reviews Pwm Driver Ic

Basic 16x2 Character LCD - RGB Backlight 5V

DRIVER IC: The module driver IC is for AIP650 (compatible for TM650), as well as supports multiple display characters..
4 DIGIT 7 SEGMENT: The digital tube display module is designed for 4 digit 7 segment, with stable and reliable performance..
CONTROL INTERFACE: With 4 pins, SDA is bidirectional data line, SCL is clock line, GND is for ground line, and VCC is power supply..
COMPACT STRUCTURE: The LED digital tube module is exquisite and compact, which can be flexibly used in a variety of situations..
WIDE APPLICATION: This module is suitable for Raspberry Pi 3 B+ 4, for DIY electronic devices, toy cars and instrumentation etc..

2560 control board: The board is a microcontroller board based on the 16AU .It has 54 digital input/output pins (of which 14 can be used as PWM....
RAMPS 1.4: RAMPS interfaces an for Arduino with the powerful for Arduino platform and has plenty room for expansion. The modular design includes plug....
LCD 12864 with Controller: This full graphic Smart Controller contains a SD-Card reader, an rotary encoder and a 128 x 64 dot matrix LCD display. You....
A4988 driver module: A4988 Stepper Motor Driver Board is a breakout board for Allegro?ˉs A4988 DMOS Microstepping Driver with Translator and....
Warning: Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver. (More generally, rewiring anything while it....

DRIVER IC: The module driver IC is for AIP650 (compatible for TM650), as well as supports multiple display characters..
4 DIGIT 7 SEGMENT: The digital tube display module is designed for 4 digit 7 segment, with stable and reliable performance..
CONTROL INTERFACE: With 4 pins, SDA is bidirectional data line, SCL is clock line, GND is for ground line, and VCC is power supply..
COMPACT STRUCTURE: The LED digital tube module is exquisite and compact, which can be flexibly used in a variety of situations..
WIDE APPLICATION: This module is suitable for 3 B+ 4, for DIY electronic devices, toy cars and instrumentation etc..

Artemis General Features: 1M Flash / 384k RAM, 48MHz / 96MHz turbo available, 6uA/MHz (operates less than 5mW at full operation), 48 GPIO - all interrupt capable, 31 PWM channels, Built in BLE radio and antenna.
Additional Artemis Features: 10 ADC channels with 14-bit precision with up to 2.67, million samples per second effective continuous, multi-slot sampling rate.
Additional Artemis Features: 2 channel differential ADC, 2 UARTs, 6 I2C buses, 6 SPI buses, 2/4/8-bit SPI bus, PDM interface, I2S Interface, Secure 'Smart Card' interface, FCC/IC/CE Certified (ID Number 2ASW8-ART3MIS).
Specific Peripherals made available on MicroMod Artemis: 1x USB dedicated for programming and debug, 1x UART with flow control, 2x I2C, 1x SPI, 1x Quad-SPI, 8x Fast GPIO, 2x Digital Pins, 2x Analog Pins, 2x PWM, 1x Differential ADC pair, Status LED, VIN Level ADC.
Additional peripherals are available but are shared on dedicated MicroMod pins. Processor board only, additional carrier board(s) will be needed to use..

DROK pulse generator module operating voltage range is DC 3.3-30V, adjustable pwm frequency range is 1Hz-150kHz, adjustable duty ratio range is 0%-100%..
Application: it can be used as a square wave signal generator, generate square wave signal for experimental development.
generate square wave signal to control the motor driver.
generate adjustable pulse to control the relevant circuit (PWM dimming speed application etc)..
High Frequency Resolution: frequency in range 1Hz~999Hz, display resolution is 1Hz.
range 1.00kHz~9.99kHz, display resolution is 0.01kHz.
range 10.0kHz~99.9kHz, display resolution is 0.1kHz.
range 1kHz~150kHz, display resolution is 1kHz..
TTL Level Communication: the frequency meter is designed with single-chip TTL level communication, communication standard is 9600 bps..
LCD Display: the blue LCD clearly displays frequency and duty ratio, PWM output can set frequency and duty ratio independently..

Main Control Chip: EMF8BB21F16G main control chip, operating frequency up to 48MHz, 3 in 1 IC driver, imported high quality high frequency ceramic capacitor. High end PCB production process, pads are metalized edge cladding, so that you can avoid pads falling off when using. 3 ounces copper thick, six layers plate, greatly reduces heat, resulting in higher efficiency.
High Performance 45A ESC: Integrated with 4pcs high performance 45A ESC, double hole spacing design. With such a high degree of integration, the volume is only general size with the traversing machine, and the installation and wiring will become very simple. This incredible size and volume is specially designed for the racing class traverser.
Multiple Functions: Using BLHeli‑S firmware, powerful performance, support a variety of ways to set the ESC parameters, or upgrade the ESC firmware (such as through the throttle signal cable, using other development boards, or using cleanflight or Betaflight firmware to set or upgrade the ESC).
Anti Interference and Quick Response: Support not only ordinary PWM throttle mode, Oneshot125, Oneshot42 and Multshot ultra high speed throttle signal, but also the latest dshot 150, 300, 600 digital throttle for anti interference and quick response. Input an....

2.8 inch TFT LCD color screen, support 65K color display, and the display is colorful, high quality image display and wide viewing angle..
With PCB board (including power supply IC, touch IC, SD card cage) compatible 5110 interface. At least 4 IO driver are needed (without touch) , at least 9 IO driver are needed( with touch)..
This 2.8-inch LCD module uses ILI9341 drive chip to drive 240*320 dot , with 240*320 resolution..
On-board level translation programs truly perfectly compatible 5V / 3.3V IO level, supports a variety of single-chip IO connection, professional and practical..
We strive to provide you with the highest quality product and the best customer experience, if you're not entirely satisfied, please just feel free to contact us at any time..