Reviews Servo To Pwm Converter Board

15 Pcs Servo Extension Cable JST Y Connector 3 Pin JST Plug Splitters Male to Female Servo Adapter JST Extension Servo Wire Connector Compatible with RC JR Futaba RC Car or Airplanes, 3 Styles

You Will Get: the package comes with 15 pieces of servo extension cables, including 5 pieces of male JST to female JR (Futaba) cable, 5 pieces of male to 2 female Y harness, 5 pieces of male to 3 female Y harness, sufficient quantities and multiple styles can satisfy your different using needs.
Proper Size: the servo connector is about 15 cm/ 5.9 inches in length, suitable size for your to use, with colors of white, black and red.
Wide Application: these JST plug splitters are compatible with Futaba and JR servo, plane and helicopter servo connection or receiver connection, also suitable for remote control car, RC car and so on, providing a lot of usages for you.
Nice Craftmanship: the JST plug connector is made of quality PVC material, which has good insulation and flame retardant, and the interior is made of tinned copper, featured a good transmission and low resistance performance, you can rest assured to use it.
Practical Function: the servo wire connector can be applied for jumping from board to board, or nice to control panel cable remote control part that is male to female.

5V isolate with MCU, and effectively protect MCU.
Voltage indication of motor driver output end.
Just need four lines from MCU to driver module (GND. 5V. PWM1. PWM2).
isolation chip 5 V power supply (can share with MCU 5 V)..
Able to reverse the motor forward, two PWM input frequency up to 25kHZ.
two heat flow passing through an error signal output..
Isolated chip 5V power supply (can be shared with the MCU 5V), can also use the on-board 5V supply.

10CM Male to Male JR Plug Servo Extension Lead Wire Cable.
Great for jumping from board to board or just about anything else..
There is a 3-pin JST RE connector on both ends. These are simple jumper wires used on standard 0.1" breakaway headers..
Length:100mm Type:JR Plug Servo Extension wire (Male to Male).

...SD, or as a high-speed mass storage device as a media library for NAS or Volumio..
Integrated with CH340E chip and DB9 male header, RS232 or RS485 function can be selected by DIP switch. The TXD/RXD signal has LED indicators to show the communication process of sending and receiving. Can be connected to PLC, stepper/servo drive, LORA module....
The display is equipped with 2 damping shaft brackets, the display angle can be adjusted arbitrarily, and the brackets can also be removed to install the case. The STL file for the 3D printed case is available under eleclab-rpi/7INCH_DSI_DISPLAY, and the fan case STL file is under eleclab-rpi/rpi_fan_case..

Used for RC cars trucks airplanes helicopters rc boat servo connection, receiver connection and flight control board..
This servo Y-cable allows you to control two servos with one radio channel..
Material: 22AWG silicone wire.Wire Length: 7CM/2.75".
3Pin wire cable.Male JR plug to 2 Female JR plug Y Harness cable..
Pack of 6 JR style servo splitter cable,unique design, professional quality JR style connectors..

PER Mode --- used as a USB buck boost converter with constant voltage and current function, input voltage range DC 3.5-15V, output voltage range DC....
VAH Mode --- used as a multimeter to measure and display voltage, current, power, capacity, energy, time and temp, detect fast charge protocol. Input....
PWM Mode --- output PWM signal, adjustable frequency, duty ratio, amplitude..
Support Fast Charging Protocol --- QC 2.0, QC 3.0, Huawei FCP/SCP, Samsung AFC..
Temperature --- can be switched between Fahrenheit and Celsius..

（pack of 6 ）This D1 mini module is a mini WIFI board based on ESP-8266EX..
Our D1 mini development board is 100% compatible with Arduino WeMos and can be programmed in Compatible with Arduino IDE..
Support OTA on line.Compatible withArduino compatibility. Using Compatible with Arduino IDE for programming..
This WLAN board contains 11 digital input / output pins, all pins have interrupt / pwm / I2C / 1-wire and a micro-USB connection..
11 digital input / output pins, all pins with interrupt / PWM / I2C / support 1 line (except D0).
1 analog input(3.2V max input). Micro USB connection.

2 in 1 Combo Mini PCI- E 2 Lane M.2 NGFF & mSATA SSD to SATA 3.0 III Adapter Converter PCBA, 2.5" SATA SSD Form Factor : 98 x 65.5mm.
M.2 (NGFF) & mSATA to SATA III Module, Build in Mini PCI-e 52pin Female connector, Build in M.2 (NGFF) B key Female connector, Insert both M.2 & mSATA....
PCI Express M.2 Spec. Revision 0.7, Version 1.0, PCI Express Mini Card Electromechanical Spec. 1.2, PWM synchronous buck converter Power IC.
3A maximum output current, Short circuit protection, In-rush current suppression, Thermal shutdown protection, ESD HBM (Human Body Mode)/2KV.
the MSATA and NGFF SSD cannot work at same time. The adapter only work for B-key or B/M-key socket NGFF SSD, cannot work for M-key socket..