Reviews Ptfe Bushing

Ajax Tools Pneumatic Brake Pin & Bushing Driver Kit (AJX-A1166)

Includes One Mercedes Benz Bushing Remover/Installer.
Designed to Remove and Replace Metallic Bushings on Mercedes Rear Axles.
Services Almost All Mercedes Passenger Cars from 1984 and Up.
Features a Pressure Piece that Provides Correct Position of Replacement Bushing.
Includes a Cut-Out In Cap to Allow Sighting of Bushing Position.

【Tips】8AN PTFE hose end can be work with PTFE fuel line ONLY.It can NOT be installed on braided CPE fuel line..
【Size】Thread Size of 8AN PTFE Fitting 90 Degree is 3/4-16UNF and the PTFE fuel line which works with should be 1/2"..
【Included】2 PCS x PTFE 8AN Fitting 90 Degree.
【Attention】100% product quality assurance. Please feel free to contact us, if you are dissatisfied with the product you received or have quality problems..
SINTLY Provide plently kind of fuel fittings, swivel, push-on lock, PTFE hose end and other fitting adapters..

For use with AXA tool post 250-100 or 250-111. up to 12" swing..
Equipped with a split bushing to accommodate a boring bar of smaller diameter. Holds 5/8" tool with bushing, 3/4" diameter without bushing.

【Package Included】25Ft 6AN nylon braided PTFE fuel injection line hose*1，6AN PTFE straight hose end*6，6AN PTFE 45 Degree hose end*2，6AN to 3/8" hose adapter fitting*2， AN6 to 3/8"quick disconnect male*1，6AN to 5/16" hose adapter fitting*1..
【Premium Material】Nylon braided PTFE fuel line hose and aluminum alloy fittings..
【Product Performance】PTFE fuel line with long service life, wear resistance and high temperature resistance. Withstands Operating Temperatures from -76℉ to 446℉ (-60℃ to 230℃). Maximum working pressure: 3000 psi. Bursting pressure: 10000psi. .
【Application】This PTFE Fuel line Kit can be worked with petrol, diesel, oil, hydraulic fluid, pump gas, alcohol, E85, coolant, fuel. This kit can be used in EFI LS system, ls engine swap and EFI conversion fuel line, turbo oil feed and boost line, transmission oil cooler line, carb fuel line, fuel return line, vapor return line, vacuum line, fuel supply line and turbocharger fuel line..
【Installation recommended】 PTFE hose relatively hard, it can't be bend and folding in h....

1.Constructed of Premium Material: The injection fuel line made of black nylon fiber braided outer cover, 304 stainless steel wire braided middle layer, and a PTFE synthetic inner line. Not recommended installation in corrosive environment, 6AN braided fuel line's service life will be influenced..
2.Wide Application:The 6AN PTFE fuel line mostly used in EFI LS system and can be worked with petrol, diesel, oil, hydraulic fluid, pump gas, alcohol, E85, coolant, fuel. PTFE fuel line most stronger to extreme circumstances than the nylon braided fuel line. long service life, wear resistance and high temperature resistance..
3.Operating Temperature Can Even Use it at -76℉(Min) or 446℉(Max) (-60℃ to 230℃). Maximum Working Pressure(psi) : 3000psi. Bursting Pressure(psi) : 10000psi. PTFE tube fuel hose length: 25Ft, inner diameter: 0.3inch (8mm), outside diameter: 0.47inch (12mm) . Please make sure the dimension, pressure and temperature range before purchase!.
4.Package Included: 25Ft 6AN braided fuel injection line hose , fuel PTFE tube and aluminum alloy fitting adapter: 6pcs 6AN PTFE straight hose end, 2pcs 6AN PTFE 45 Degree hose end, , 2pcs 6AN to 3/8" hose adapter fitting, 2pcs 6AN to 1/4"NPT hose adapter fitting , 1pc AN6 to 3/8"quick disconnect ....

【Application】This rear suspension bushing removal tool has a wide range of application and strong practicality. It is suitable for Ford Focus MK1 & MKII 1998-2007, Ford Cuga 2008, Ford C-Max 2007, Mazda 3 sedan, hatchback 2003-2008, suitable for Mazda 5 CR, CW, MPV 2005, applicable to V50 2004-2012, applicable to S40 MK sedan 2003-2012..
【Performance】This rear suspension bushing kit has excellent performance, protects your car from scratches, no marks or scratches, and is used to silently press in and pull out the rear of the shaft to improve safety and reliability..
【Easy to use】Designed for the removal and installation of bushes and bearings, this rear trailing arm bushing tool is easy to use and install without the need to remove the rear axle, saving a lot of time..
【Material】This control arm bushing removal tool is made of selected carbon steel. The greater the hardness, the higher the strength, but the lower the plasticity, the stronger the rust prevention, the longer the durability and the longer the service life..
【After-sales Service】This rear control arm bushing kit has been strictly tested before leaving the factory.If you encounter any problems in the use process, please contact our customer service in time, and we wil....

The New PS27 F/G-Nock bushing was designed for accuracy. This Bushing is designed to perform flawlessly after taking a beating in competition or practice..
This bushing will be longer lasting with less maintenance!! That means more time practicing and less time fixing arrows!!.
Made with 7075-T6 Aluminum to ensure every shot counts!.
Will accept both the F-Nock and M/G-Nock.

Fitment - ID: 5/16". OD: 0.465inch.Length: 20 feet(6M). Please measure before purchase! (Includes: as shown in the picture.).
High Quality Material - The hose is made of high-quality PTFE, which has good chemical resistance and heat resistance. The outer layer is woven black nylon, which has high durability, extreme pressure resistance, and a professional and high-tech appearance..
High Performance - The high-performance AN-6 nylon and stainless steel braided high-pressure PTFE fuel line kit is much more resistant to high temperatures and extreme environments. The PTFE lined hose is compatible with all vehicle fuels, lubricants and coolants. Teflon hoses are relatively hard and cannot be bent..
Warm Tips - 1.Avoid twisting hose when installing 2.Allow some slack in assembly for changes in length that occur underpressure 3.When routing hose line, provide a smooth bend radius.4.Avoid sharp bends which may cause hose tocollapse and restrict flow..
Package Include - AN-6 Black Nylon PTFE Fuel Hose x 20ft, AN-6 Straight PTFE Fitting x 4, AN-6 45 degree PTFE Fitting x 2, AN-6 90 deg....

Taper bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
Sintered steel for greater strength and resistance to wear than steel.
Keyed to the shaft to prevent the shaft from rotating in the bushing.
Interchangeable with taper bushings from various manufacturers.