Xiuxin 2pcs 5V 8 Channel Relay Module Board for Arduino PIC AVR DSP ARM
- 2pcs/lot 8 Channel relay module board, Working voltage: 5V.
- This board is for Arduino PIC AVR DSP ARM.
- Support all single-chip microcomputer control,Industrial circle,PLC controller,Household intelligent control.
- Relay output maximum contact is AC250V 10A and DC30V 10A.
- Widely used for all MCU control, industrial sector, PLC control, smart home control..
Check StockSainSmart 16-Channel 12V Relay Module Board for Arduino DSP AVR PIC ARM
- 12V 16-Channel Relay interface board, and each one needs 15-20mA Driver Current.
- Equipped with high-current relay, AC250V 10A.
- Standard interface that can be controlled directly by microcontroller (Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP433, TTL logic).
- Indication LED's for Relay output status.
Check StockXYGStudy Raspberry Pi Expansion Board Power Relay Module for Raspberry Pi 4 3 2 Model B B+ A+
- Raspberry Pi Expansion Board, Power Relay.
- The RPi Relay Board gives your Pi the ability to control high voltage/high current devices, easily makes normal home appliances become intelligent..
- Standard Raspberry Pi 40PIN GPIO extension header, Supports Raspberry Pi A+/B+/2B/3B/3B+/4B and later versions.
- High quality relays, loads up to 5A 250V AC or 5A 30V DC.
- Photo coupling isolation, prevent interference from high voltage circuit.
Check StockSparkFun Qwiic Single Relay-Up to 5.5A at 240VAC Multiple I2C addresses Available Turn on/Off high Power Device from Low Power microcontroller No Soldering Large Power Loads w/Simple I2C Commands
- Have you ever wanted to control something powerful or have you ever needed to turn on/off a high power device from your Arduino compatible board or another low powered microcontroller? No soldering needed to get started. Plug and play. Code available. Small footprint..
- The Single Relay board can handle up to 5.5A at 240VAC for long periods of time and allows you to control large power loads with simple I2C commands. Utilizing our handy Qwiic system, and on-board screw terminals, no soldering is required to connect it to the rest of your system!.
- The Qwiic Relay comes with a default I2C address of 0x18 but can be changed with a simple command allowing you to control over 100 Qwiic Relays on a single bus (but please be aware that toggling lots of relays on a 3.3V bus can cause voltage spikes so an external power supply will be required)!.
- In addition, there is an address jumper on the back of the board. Closing this jumper with solder will change the address to 0x19..
- Operating Voltage: 1.7V-3.6V. Coil Resistance: 23.5Ω. I2C Address: 0x18 (Default), (Jumper changes to 0x19). Max Current (Through Relay): 5.5A (240 VAC).
Check StockDiyeeni 4-Channel 12V USB Control Switch Relay Module, Relay Board Computer Smart Switch Controller, PC Relay Module Expansion Board, Relay Board for Automation
- Onboard square USB interface, stable connection..
- Use imported high performance USB control chip..
- Use the special relay drive chip ULN2803, the relay works more stable..
- Board power socket and terminal, two ways to access the power supply are convenient and flexible..
Check StockWinnerEco 5pcs 1 Channel DC 5V Relay Switch Module for Raspberry Pi ARM AVR
- 1-channel relay interface board which can be controlled directly by a wide range of microcontrollers. Controllers includes AVR, PIC, ARM, PLC, etc..
- Relay output maximum contact is AC110V ~ AC250V 10A and DC30V 10A..
- Standard interface can be directly connected with microcontrollers..
- Red working status indicator for power on indication.Green working status indicator for relay the switch..
- It can control various appliances and other equipments with large current.Widely used for all MCU control, industrial sector, PLC control, smart home control..
Check StockElectronics-Salon 8 Channel DPDT Signal Relay Module Board (Operating Voltage: DC 5V)
- 8 Channel DPDT Signal Relay Module Board, DC 5V Version..
- FR-4 fiber glass PCB, dual copper layers. Dimensions: 72.5mm x 150mm ( L x W )..
- RY5W-K high quality signal relays, LED indicator for each relay channel. Darlington transistors circuit driving relay, improve the reliability of action..
- Pitch 3.81mm / 0.15" screw terminal block, wire range 26-16AWG, strip length 5mm / 0.2", Metric M2 slotted screw..
- Datasheet: https://images-na.ssl-images-amazon.com/images/I/A1vg1+5HA8L.pdf.
Check StockDPST 1NO 1NC 8Amp Power Relay Module, Briidea 24V AC/DC Power Relay Control Voltage, White
- INPUT CONTROL SIGNAL: Voltage AC or DC 24V, Current 17mA..
- OUTPUT CURRENT: Output switch DPST 1NO 1NC(Double Pole Single Throw, 1 Normally Open and 1 Normally Close ), rated current 8A/250VAC or 8A/30VDC (one switch)..
- SIMPLE & PRACTICAL: This passive power relay module is simple and practical, which is very convenient to use. It can support both Normally Open and Normally Close..
- EASY MOUNT: The power relay is of compact plastic case and wires connects for easy mount. Two screw mounting holes are convenient for you to fix it on the wall or wooden board. Of course, you can also choose not to lock the screw..
- LED INDICATION: This power relay has a led indicator for relay action indication. It is obvious to know the status of the switch at a glance..
Check StockHow to Use a Breadboard! (Make: Handbook)
- 30A High Current 12V Contactor relay Switch DC power Switching Control Board.
- Using high-quality ultra-small optocoupler, anti-interference ability, stable performance..
- Using 9.5mm black fence terminal, standard 30A terminal, stable and solid, reliable quality..
Check Stock