Reviews Voltage Tester With Low Impedance Mode

Non-Contact Voltage Tester, Dual Range Voltage Tester AC 12V-1000V/48V-1000V, ENGiNDOT Live/Null Wire Tester, Electrical Tester with LCD Display, Buzzer & Light Alarm, Breakpoint Test (Blue)

  • 【Safety Non-Contact Voltage Tester】Non-Contact Voltage Tester is safer for testing all Electric Appliances in Your Family. The tester with NCV inductive probe for AC voltage Just places the tip near a terminal strip, outlet, or supply cord. When the tip glows red and the pen beeps, you know there's voltage present. The live wire detector can automatically detect the live or neutral wire..
  • 【 High-Efficiency And Convenient 】The tester with LCD display. When the voltage is detected, the alarm will send out green or red light and beep. When the higher the sensed voltage or the closer it is to the voltage source, it beeps at a higher frequency. At the same time, the screen will be red or green, red means the high voltage and live wire are detected, green means the low voltage and null wire are detected..
  • 【DUAL RANGE/ High&Low Sensitivity】The sensitivity/flashlight key can be switched at high and low sensitivity. Detect high and low voltage (AC 12-1000V /48-1000V )Press the S button to adjust sensitivity and adapt low range for doorbells, thermostats, irrigation wiring..
  • 【Multifunction Design 】Use the Non-Contact Voltage Detector in Circuit Breakers, Lighting Fixtures, Switches, Outlets, Wires, and Anywhere You Need it. Bright LED flashli....
Check Stock

TopDiag BT200 Car Battery Tester, 12V 24V Load Tester, 100-2000 CCA Automotive Charging Cranking System Tester Digital Auto Battery Analyzer for Car Truck Motorcycle SUV Boat (BT200)

  • ... [Fast & Accurate Detection]➤ The digital battery tester automotive has a built-in millisecond level custom integrated chip and uses advanced conductivity technology to directly present the battery's state of health (SOH), state of charge (SOC), test result display value with actual voltage, rated CCA value, measured CCA value, and resistance value in a digital display. It only takes 3 seconds to display the test results with 99.6% accuracy..
  • [Battery & Cranking & Charging & Wave Test]➤ Compared with other automotive battery testers, this car battery analyzer has added 1 more mode, and there are 4 test modes in total. The battery cca tester can not only test the startup of the starter system, but also monitor the battery health of the charging system and the waveform of the voltage. No longer have to drive miles to the repair shop to get it checked, which is convenient and money-saving for you..
  • [Easy to Operate]➤ The red clip of the TopDiag Car battery tester 12v battery analyzer is connected to the positive "+", and the black clip is connected to the negative "-". Select the corresponding test mo....
Check Stock

Binval Digital Multimeter 2 in 1 USB C Tester LCD Color Display Voltage Current Watt Meter Automatic Detection and Identification of Charging Protocols Covering Display: DC3.6-32V/0-5.1A

  • ...le alarm, sudden power failure to save data..
  • 【Newest Upgraded IPS color screen】: The new upgraded version provides 8 LCD main color screen display interface, key switch display interface. Through the new interface settings, support OTG function, monitor the voltage, current, capacity, power, USB’s power, load impedance, D/D-voltage and other data of USB or type c supported devices. Switch multiple interfaces with the click of a button. (Support 180 degree flip screen, 3 kinds of personalized interface!).
  • 【Wide Application】: USB tester comes with OTG adapter, supports PD3.0/PD2.0, QC3.0/QC2.0, BC1.2 and USB A or USB C port, supports newer iPhone 11 Pro phones. (Support iphone 11/X/iPhone Xs fast charging, 29W power, 5V3A / 9V3A / 12V2.5A / 15V2A) Compatible with the new MacBook Pro, MacBook, iMac, iMac Pro, Dell XPS, Acer Aspire, HP Spectre , ASUE Zenbook , Lenovo Thinkpad, Eluktronics, Razer Blade Stealth, Chromebook, Microsoft Surface Pro and many more Type C devices and chargers..
  • 【BINVAL PROMISE】: We always believe in stability and continuous improvement of the quality of our products. We trust our products and we offer a worry-free service for 18 months. Feel free to ask our team any questions about use. If you are not satisfied with ....
Check Stock

TopDiag P200 Automotive Circuit Tester, Power Circuit Probe Kit, 9~30V with Multimeter/Relay/Fuel Injector Tester/Activating Component/0~5V Power with 20ft Cable for 12V 24V Vehicle

  • ...ful functions, namely: ✅Fuel Injector Test✅ Relay test mode. TopDiag makes diagnosing your car easier and saves maintenance costs..
  • 【0~5V Adjustable Power Supply & Activating Components】0~5V power is useful when checking the wiring to the ECU/ECM, also meet the voltage requirements for the sensitive parts with low voltage. Besides positive activation, negative activation is our newest function which others none, power on components at a moment notice..
  • 【Smart Test & Positive & Negative Test】When connected to the probe of Car Electrical Test Tool to measure voltage, resistance, positive/negative polarity, it will automatically become an instant auto-range, intelligent judgment does not require manual selection, and the corresponding parameter values and prompts are displayed on the HD LCD screen. With a 20ft cable, you can quickly assist you in diagnosing the car's condition without opening the wiring..
  • 【Multimeter & Oscilloscope Tester】The P200 Circuit tester will be the more versatile and powerful Power Circuit Probe Kit you've ever seen. Contains the multimeter's DC voltage (....
Check Stock

High Speed Comparator High Speed Frequency Meter Front Shaping Comparator for Low-Voltage Applications Conversion Circuit

  • LOW VOLTAGE APPLICATIONS -- The input common mode range is better than the swing input, which is very suitable for low voltage applications..
  • APPLICATION -- Digital module can be used for wide voltage range and periodic signal shaping..
  • FRONT END ADJUSTMENT -- Used as a front end conditioning module in time domain measurements for frequency and phase difference..
  • PARAMETER -- The input voltage is 10 to 1000mV, the input frequency is about 200MHz DC, and the input impedance is 50 ohms..
  • RAIL TO RAIL OUTPUT -- The output level mode is rail to rail output, which can directly drive TTL / CMOS level..
Check Stock

ANCEL BST200 12V Car Battery Load Tester with ANCEL PB100 Automotive 12/24V Circuit Tester Probe

  • Includes: 1 x BST200 Battery Tester, 1x PB100 Circuit Tester.
  • Works on automotive 12V 100 - 1100 CCA lead-acid batteries, including regular flooded, AGM flat plate, AGM spiral, and GEL batteries for cars, SUV, motorcycle, light truck, and more..
  • Gives you an accurate result in only 3 seconds, such as CCA value, CCA rating, voltage, internal resistance, state of health, and state of charge, based on the rating standard of CCA, CA, MCA, JIS, DIN, IEC, EN and SAE..
  • A MUST-HAVE TOOL - Designed for voltage & polarity testing, continuity testing, signal circuit testing, supply power/activating components, trailer lights & connections testing. It features red/green polarity indicators, follows & locates short circuits, and checks bad Ground contacts..
  • 4 WORKING MODES - DC Voltage mode for reading the DC voltage with a resolution of 0.1 volts.
  • AC Voltage mode for reading the Max. voltage, the Min. voltage, and frequency.
  • Resistance mode for reading the resistance between the tip and auxiliary ground lead.
  • Diode mode for checking forward bias or reverse bias..
Check Stock

ANCEL PB100 Automotive 12/24V Power Circuit Tester Probe with ANCEL BA201 Car 12V 100-2000 CCA Battery Load Tester

  • Includes: 1 x PB100 Circuit Tester, 1x BA201 Battery Tester.
  • A MUST-HAVE TOOL - Designed for voltage & polarity testing, continuity testing, signal circuit testing, supply power/activating components, trailer lights & connections testing. It features red/green polarity indicators, follows & locates short circuits, and checks bad Ground contacts..
  • 4 WORKING MODES - DC Voltage mode for reading the DC voltage with a resolution of 0.1 volts.
  • AC Voltage mode for reading the Max. voltage, the Min. voltage, and frequency.
  • Resistance mode for reading the resistance between the tip and auxiliary ground lead.
  • Diode mode for checking forward bias or reverse bias..
  • Easy to check the cranking and charging system condition. Cranking test displays cranking time, voltage and status, which helps you test and analyze the starting motor to check it works properly or not. Charging test displays load voltage, unloaded voltage, ripple status, charging system status to avoid damaging the battery and shortening its life greatly due to overcharging or incomplete charging..
  • Monitors the real-time voltage through the Waveform graph, displays current voltage, maximum and minimum voltage during ignition. According to analyze the values of discharge voltage, starting voltage, and cha....
Check Stock

ANCEL PB100 Automotive 12/24V Power Circuit Tester Probe with ANCEL BA301 6V 12V Battery Load Tester Car Cranking Charging System Test Tool

  • Includes: 1 x PB100 Circuit Tester, 1x BA301 Battery Tester.
  • A MUST-HAVE TOOL - Designed for voltage & polarity testing, continuity testing, signal circuit testing, supply power/activating components, trailer lights & connections testing. It features red/green polarity indicators, follows & locates short circuits, and checks bad Ground contacts..
  • 4 WORKING MODES - DC Voltage mode for reading the DC voltage with a resolution of 0.1 volts.
  • AC Voltage mode for reading the Max. voltage, the Min. voltage, and frequency.
  • Resistance mode for reading the resistance between the tip and auxiliary ground lead.
  • Diode mode for checking forward bias or reverse bias..
  • Works on all 6V & 12V 100 - 2000 CCA lead-acid batteries, analyzes starter cranking and alternator charging condition. Cranking test to test and analyze the starting motor (cranking time, voltage, and status), and the charging test to check and analyze the charging system (load voltage, unloaded voltage, ripple status, charging system status)..
  • Features one-click "waveform" to record the voltage changes (current voltage, maximum and minimum voltage) in a graph during ignition. You'll know if the battery needs to be replaced or not through analyzing the values of discharge voltage, starting voltage, and ch....
Check Stock

Juried Engineering TL072CP TL072 IC JFET Operational Amplifier & 8-Pin DIP Sockets with Machined Contact Pins Breadboard-Friendly (Pack of 5)

  • The TL072 JFET-input operational amplifiers incorporate well-matched, high-voltage JFET and bipolar transistors in a monolithic integrated circuit. The devices feature high slew rates, low-input bias and offset currents, and low offset-voltage temperature coefficient..
  • Low Power Consumption, Wide Common-Mode and Differential Voltage Ranges, Low Input Bias and Offset Currents.
  • Output Short-Circuit Protection, Low Total Harmonic Distortion: 0.003% (Typical), Low Noise Vn = 18 nV/√Hz (Typical) at f = 1 kHz.
  • High-Input Impedance: JFET Input Stage, Internal Frequency Compensation, Latch-Up-Free Operation.
  • High Slew Rate: 13 V/µs (Typical), Common-Mode Input Voltage Range Includes VCC+, Example Applications: Motor Integrated Systems: UPS, Drives and Control Solutions: AC Inverter and VF Drives, Renewables: Solar Inverters, Pro Audio Mixers, DLP Front Projection System, Oscilloscopes.
Check Stock