Reviews Transmission Bearing Puller

KUNTEC 3 Jaw Inner Bearing Puller Heavy Duty Pilot Sleeve Gear Extractor Internal External Pulling for Motorcycle Wheel Car SUV

  • 【Strong Material】3-Jaw Inner Bearing Puller Tool is constructed from carbon steel, the overall heat treatment, strong and durable. Corrosion-Resistant black oxide finish, preventing damage to bearings..
  • 【Well Equipped】3 Jaw Inner Bearing Puller removes bearings, pump bearings, bushings, removes all sleeve type bearings with 1/2"-2" inside diameter.
  • 【Advantage】The three-jaw design can apply pressure evenly to prevent damage to the bearing and ensure stability during use. There are two installation methods for the claw foot..
  • 【Labor Saving】Structure design, gently turning the small wrench can produce a strong pull force.
  • 【Wide Application】3 Jaw Bearing Puller is designed for automotive flywheel, motorcycle wheel, bicycle wheel, pump bearing, generator bearing, machine bearing etc.
Check Stock

VEVOR Carrier & Pinion Bearing Puller Compatible with Dana 30,40,50,60,70, 80, Ford 10.25  Bearings Pinion Puller Tool with 3 Clamshells 45# Steel Clamshell Bearing Puller for Auto Repair

  • Great Compatibility: The clamshell carrier bearing puller is compatible with Dana 30, 40, 60, 70, Ford 10.25" bearings. With the clamshell bearing puller, you can quickly remove the bearings. In addition, its power is evenly distributed, so less damage will be brought to your pinion bearings..
  • Premium Performance & Features: With high working efficiency, this carrier pinion bearing puller can effortlessly remove the pinion bearings with minor damage, drastically reducing dismantled time. And the carrier bearing puller will no longer easily pry into the pinion's sealing surface..
  • Complete Equipment: All necessary parts are ready for you. There is a main puller body, plug, center bolt, 3 clamshells, retaining ring, and adjuster rings. Besides, this unit comes with a handy stand, so you can group all the working parts together..
  • Easy to Operate: There is no need for other complex working tools. Firstly, place the main body over the plug and adjust the lower and upper adjusting ring. Secondly, select a proper clamshell and tighten the retaining ring. Finally, you can use an impact gun to remove the bearing..
  • Superior Material: The clamshell bearing tool is made of durable 45# steel, providing good performance in withstanding abrasion, corrosion, and impa....
Check Stock

Bonvoisin 5T Hydraulic Gear Puller Set Wheel Bearing Puller Kit 2 or 3 Jaws Pulling Separator for Wheel Hubs Rotors Car Axles Pulleys Brake Drums

  • Drop-forged Cr-V steel jaws are heat-treated for extra strength and durability. This 3-jaw removal tool works with your wrench, ratchet, or spanner as a gear puller, sprocket puller, bearing puller, pulley puller, flywheel puller and more..
  • Three jaws come with fine chrome plating to provide a reliable and effective rust and corrosion protection. Drive screw is covered by black phosphatizing, which provides maximum strength and longevity to the gear puller, puller jaws allow for easy gripping and access to tight spaces. No need to assemble yourself is the advantage of DURATECH..
  • Each of the three 3-jaw gear and bearing pullers can be reversed to pull parts from either the inside or outside. Universal 8 position reversible jaws offer inside or outside grip with short, standard, long or extra-long reach..
  • Three-jaw design balances the pulling force well, and claws are precisely machined to give a non-slip and secure grip on the gears. Make it deal for pulling work in confined areas..
  • Jaw Spread: 8in, Jaw Reach: 9-1/16in, Puller: 12T. Perfect for you to smoothly and safely slide gear, pulley, bearing, and flywheel off the shaft. Free replacement insures your DURATECH Wrenches purchase against manufacturer defects..
Check Stock

Puller Set, 13 Pieces, Bar

  • Separator tools are used with bar puller and legs for a wide variety of pulling jobs.
  • Includes the two most popular bearing splitters - 2 inch and 3 inch - plus four sets of hex push puller legs.
  • 5 inch bar-type puller head with forcing screw.
  • The 5 inch puller cross-bar with a 6-1/4 inch forcing screw and each of the bearing separators may be used separately or in combination with other pullers or tools.
  • Blow-molded plastic storage case keeps set contents organized and protected from loss.
Check Stock

ABN 8in 3-Jaw Gear Puller – Removal Tool for Slide Gears, Pulley, and Flywheel

  • [Durable 3 Jaw Puller Tool]: Use the ABN 8-Inch Small Gear Puller 3 Jaw Small Engine Flywheel Puller to remove most shift-fitted parts with ease.
  • 3 prong gear puller evenly distributes pulling force to protect your gears.
  • [Damage-Free Removal]: Manual bearing puller removes slide gears, pulleys, bearings, bushings, and flywheels without causing damage to your application.
  • [Multi-Position Design]: Universal pulley puller tool has reversible jaws that switch from inside to outside grip in short or long reach lengths for maximum versatility.
  • Reach measures in 4 lengths from 6.25-inches to 8-inches (15.9 to 20.3cm).
  • [Built to Last]: Forged and hardened steel provide maximum strength and longevity to the gear puller sets.
  • Slim puller jaws allow for easy gripping and access to tight spaces while the steel center bolt and acme-thread offer smooth operation.
  • [Works with your Existing Tools]: 9.5-inch (241.3mm) tall hex head screw fits any 19mm hand wrench, ratchet, or combination spanner for gear and bearing removal.
Check Stock

BESTOOL Gimbal Bearing Puller | Mercruiser Alignment Tool | OMC Heavy Duty Bearing Puller for OMC/Mercruiser Alpha/Alpha one/Bravo

  • STURDY & DURABLE:This puller alignment tool is made of solid pieces of steel. It can be a lifetime tool that will last longer..
  • WEAR PREVENTION:This gimbal bearing tool supports proper alignment that prevents wear on the bearing, drive, and coupler..
  • ALIGNMENT CHECK:Our bearing installer puller can be used to check engine coupler alignment with the gimbal bearing and drive..
  • EASY TO USE:After assembling, the seal bellow expander tool works just as well as the one-piece tools, which can save space in this way..
  • VARIOUS APPLICATION: This GIMBAL bearing puller tool will remove bearings on Mercruisers, OMC, and Cobra Bell Housings..
Check Stock

Inner CV Joint Puller Slide Hammer Front Wheel Drive Axle Half Shaft Removal Tool Kit CV Axle Removal Tool Slide Hammer 63mm 48mm CV Joint Fork Adapter Attachments

  • ⚒️ Quick to Remove CV Axle ⚒️ - With this CV axle removal tool the axle assembly is popped out of trans axle, and install the new axle,not need spend a lot of effort. Without damage to transmission case or inside roller bearing..
  • ⚒️ Perfect Joint Fork ⚒️ - This slide hammer puller set includes opening 63mm and 48mm CV joint fork disassembly adapter, the CV Joint Fork is be threaded internally, and the Slide Hammer stick is threaded externally. the joint fork could fit on the slide hammer stick, 63mm and 48mm fit most vehicle models, have wide use..
  • ⚒️ Heavy Duty ⚒️ -This slide hammer weighs 10.5 pounds and is 19.5 inches long, which is larger than the normal ones. So it has enough length to slide to generate more force, easier to use and work better.The hammer and VC joint fork are made of heavy-duty steel, durable and not easy to break..
  • ⚒️ Easy to Use ⚒️ - You need to attach the inner CV axle puller to your axle slide hammer, then place the adapter around the axle after the inner start. Slide the 10 lb. hammer weight back and forth to create torque and pull out the axle. Note: you can use....
Check Stock

ATPEAM 9-Way Slide Hammer Puller Set | Wrench Adapter Axle Bearing Hub Auto Set, Axle Front Rear Wheel Bearing Dent Hub Gear Puller Remover Set

  • Extra Durable: The ATPEAM slide hammer puller set is made of drop forged steel pullers and fully hardened shaft and accessories, this will pull the hardest wheel bearing and wheel hub out of the tight position, and make sure this tool set a longer lifespan..
  • A Complete Puller Set: 1x shank and T-bar assembly, 1x 4.8 lb. sliding hammer weight, 1x cross nut, 2x hub grappler adapter flanges, 1x large forcing screw, 1x cone, 1x 3-way puller head, 1x vise grip adapter with double lead thread, 1x seal hook adapter, 1x dent puller retainer, 1x self-tapping screw, 3x 5 inch (127 mm) internal and external jaw bars, 3x hex jaw nuts, 3x hex head cap screws, and 1x blow molded storage case..
  • Auto Body Repair Tool Set: The slide hammer bearing puller kits are body shop tools that are used to aggressively remove tightly jammed parts or dents.
  • slide hammers consist of a long metal shaft with an attachment point at one end, a heavyweight that slides along the shaft, and a handle with a stop on the opposite end.
  • this hammer tool slide kit includes 2 jaws and 3 jaw internal and external pullers, rear axle bearing puller tool, locking plier adaptor, puller hook, and auto dent puller tool.
  • Wide Application: The 9-way slide hammer puller set with 4.8 lb slide hammer is idea....
Check Stock

Two Jaw Pilot Bearing Gear Puller, Carbon Steel Adjustable Bearing Puller for Slide Gears, Pulley, and Flywheel(4inch)

  • [Adjustable]: The puller can be bilateral rotation, enable stretching size and working space.Two jaw with adjustable clamping depth, fit for different size gears and bearings.
  • [Widely Application]: These two jaw gear pullers are ideal for automotive flywheel, motorcycle wheel, bicycle wheel, pump bearing generator bearing, machine bearing etc.
  • [Easy to Use]: This bearing puller comes with hexagonal screw and thread for fastening, non-slip and high strength.Adjust screw design, flexible and convenient to repaired different size gears and bearing.
  • [Carbon Steel Material]: These two claws puller is made of carbon steel, the point of the mandrill through a special heat treatment process, more solid and durable.
  • [Service Guaranteed]: If for any reason you are not completely satisfied with any of our products, just contact us directly so we can help with whatever is needed for you.
Check Stock