Reviews Three Phase Single Phase

Things to Remember in Using Your Thought Power for the Production of New Conditions

power including active power, non-active power, and power factor.
Remote access to measurements via the Fluke Connect Condition Monitoring software.
Graphs show trends and fluctuations of the measurements during the monitoring period.
and alarm settings notify users when measurement values are outside user-set thresholds.
3540 FC Three-Phase Power Monitor is portable, wireless, battery powered, and easy to install.

1.Humanized design,the interface adopts binding posts,standard heat sink,integrated speed regulating potentiometer on the board,it can be used when the power is on,save time and effort..
2.Full patch technology,stable performance,with forward and reverse, brake function.Electric Motor Speed Controller Brushless Controller with Hall..
3.Wide voltage 6-60V high power 400W DC three-phase brushless with Hall controller..
4.High-power 400W DC three-phase brushless with Hall controller, support PLC 0-5V analog control, support PWM control, amplitude 2.5-5V.
5.There are three relatively thick phase wires on the motor, and there are also three phase wire interfaces on the driver board. They are marked with the characters of MA, MB, MC and other similar characters, and they are also connected respectively..

☞ Model: MDQ-100A is designed for single phase Full wave rectification, which has four diodes connected in a one phase bridge configuration..
☞ Max. Average Forward Rectified Current : 100A.
Production Size: 80 x 40 x 32mm/ 3.1" x 1.6" x 1.2" (L*W*T).
package content: 1 x rectifier bridge 1 net weight: 130g.
package content: 1 x rectifier bridge radiator.
☞ Applications: DC power supply for instrument equipment , Input of PWM frequence converter rectifying power supply , Excitation power supply for DC motor, Input of switch power supply and auxiliary current Inverter current..

External current probe and voltage measurements.
Over/under alarms for current and voltage visual alarm indication.
Simultaneous single phase current and voltage monitoring verification of power conditions, compressor and fan run cycles and use three LCV's for three phase applications.
Single point offset calibration available through software.

Dynamic phase loss, static phase loss protection: refers to the phase failure of any phase when the protected device is in the running state or non-operating state. The indicator light is in the form of red light and priority.
Wrong phase protection: A protection measure to prevent the phase sequence of L1, L2, L3 three-phase AC power supply from being connected incorrectly. Instant action. The indicator light is in the form of yellow light..
Voltage Unbalance Protection: Refers to a voltage imbalance that will affect the safe operation of the device. When the voltage imbalance rate is higher than 8%. The form of the indicator light is: the lack of phase red light is on, and priority..
Delay protection: When there is a fault, the monitor will delay after 1~2 seconds, and the relay will release..
The protection function of the monitor is not affected by the current of the line or load, the inrush current, the unbalanced current and the nature of the load. Long-term work with full performance and full climate. Power consumption is no more than 2W..

Dynamic phase loss, static phase loss protection: refers to the phase failure of any phase when the protected device is in the running state or non-operating state. The indicator light is in the form of red light and priority.
Wrong phase protection: A protection measure to prevent the phase sequence of L1, L2, L3 three-phase AC power supply from being connected incorrectly. Instant action. The indicator light is in the form of yellow light..
Voltage Unbalance Protection: Refers to a voltage imbalance that will affect the safe operation of the device. When the voltage imbalance rate is higher than 8%. The form of the indicator light is: the lack of phase red light is on, and priority..
Delay protection: When there is a fault, the monitor will delay after 1~2 seconds, and the relay will release..
The protection function of the monitor is not affected by the current of the line or load, the inrush current, the unbalanced current and the nature of the load. Long-term work with full performance and full climate. Power consumption is no more than 2W..

Application: Spindle Motor, Drill Press, CNC, HVAC, Lathe, Milling, Pumps, Conveyors, Mach3, Fan, Cooling, Compressor, Three-phase motor and other machines!.
Spacing 2.54mm bar connector, 5-pin plug. DC cooling fan low noise, large air volume..
The machine is screwed to ensure the safety and reliability of the use. Three anti-paint protection lines, improve and extend the life of the fuselage..
The operator panel can be moved out and extended by 2M, 1.5M, 1M, 30CM. 1 Year replace or refund!!!.

This Bridge Rectifier Warranty 1 years . If there are quality problems within 8 years, you can send us email. We will send you new ones ..
Model: MDQ-100A is designed for single phase Full wave rectification, which has four diodes connected in a one phase bridge configuration..
Max. Average Forward Rectified Current : 100A.
Production Size: 80 x 40 x 32mm/ 3.1" x 1.6" x 1.2" (L*W*T).

Phase 10 is the Rummy-type card game with a twist!.
Be the first player to complete 10 varied phases with two sets of three, one run of seven, or seven cards with the same color..
Each phase is specific for each hand, meaning each player must complete one phase before advancing to the next round!.
“Wild” and “Skip” cards add excitement and deliver game-changing moments..
Phase 10 game is fun and enjoyable for the whole family!.