Reviews Stepper Motor Servo Board

Electric CNC Linear Stage Actuator Linear Rail 200mm Stroke Cross Sliding Table SFU1605 Ballscrew C7 Slide Module for CNC Engraving Machine

1. Motor seat can be replaced by Handwheel.
2. It can be equipped with hand wheel, stepper motor, servo motor, AC motor, DC motor.
3. It can organize cross, vertical, three-axis, four-axis gantry structure.
4. The cushion is added before and after the sliding table to extend the service life of the sliding table..
5. The front end increases the diagonal bearing seat, the sliding table has high precision and better stability..

Model:3 Axis GRBL 1.1F USB Port GRBL Control Board.
Input voltage: 12-24VDC .CNC Router Machine Controller board.
Compatibility: support 12V/24V laser, TTL/PWM modulation signal, 3P interface and 2P+2P interface.
support 775 motor, 200W/300W/500W spindle.
support dual Y-axis use, three-axis and two-axis switching use.
support X/Y/Z limit switch, Z-axis probe, emergency stop switch.
Support stepper motor: 12V, within 2A maximum current, within 1.5A recommended. (Stepper motor 42, 57).⚠️Please check the wire sequence when connecting the stepper motor, the wire sequence may be different for different motors, wrong connection may burn the motor and the motherboard..
Support software：LaserGRBL/Lightburn/Candle(3 axis)/Universal Gcode Sender.
Tip: Before you connect the motherboard, please carefully check the need to connect the device wire sequence (laser, motor) to prevent a mismatch of wire sequence, burn the device. Customer service 24H online, to provide you with help..

Fully assembled & tested, no soldering required, Can be extended to control other accessories..
It has Cartesian robots and requirements of the extruder, Heated bed control with additional 11A fuse. Fits up to 5 stepper driver board..
Three field effect transistors, three heater / fan output ports, three thermistor circuits.A number of expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack..
The fifth stepper motor output port can be customized as a Z-axis motor or a second extruder.Pololu board foot socket, can be easily replaced or removed..
The modular design includes plug in stepper drivers and extruder control electronics on an MEGA shield for easy service, part replacement, upgrade-ability and expansion..

Model:3 Axis GRBL 1.1F USB Port GRBL Control Board.
Input voltage: 12-24VDC .CNC Router Machine Controller board.
Compatibility: support 12V/24V laser, TTL/PWM modulation signal, 3P interface and 2P+2P interface.
support 775 motor, 200W/300W/500W spindle.
support dual Y-axis use, three-axis and two-axis switching use.
support X/Y/Z limit switch, Z-axis probe, emergency stop switch.
Support stepper motor: 12V, within 2A maximum current, within 1.5A recommended. (Stepper motor 42, 57).⚠️Please check the wire sequence when connecting the stepper motor, the wire sequence may be different for different motors, wrong connection may burn the motor and the motherboard..
Support software：LaserGRBL/Lightburn/Candle(3 axis)/Universal Gcode Sender.
Tip: Before you connect the motherboard, please carefully check the need to connect the device wire sequence (laser, motor) to prevent a mismatch of wire sequence, burn the device. Customer service 24H online, to provide you with help..

2560 control board: The board is a microcontroller board based on the 16AU .It has 54 digital input/output pins (of which 14 can be used as PWM....
RAMPS 1.4: RAMPS interfaces an for Arduino with the powerful for Arduino platform and has plenty room for expansion. The modular design includes plug....
LCD 12864 with Controller: This full graphic Smart Controller contains a SD-Card reader, an rotary encoder and a 128 x 64 dot matrix LCD display. You....
A4988 driver module: A4988 Stepper Motor Driver Board is a breakout board for Allegro?ˉs A4988 DMOS Microstepping Driver with Translator and....
Warning: Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver. (More generally, rewiring anything while it....

Clamp-style mount for secure attachment to shaft.
Accommodates angular, and parallel misalignment.
Aluminum hubs for light weight, stainless steel discs for strength.
Shaft couplers suitable for connect servo motor, stepper motor, encoder, screw driving, machine platform, etc..

♞【Product】3 Axis nema23 stepper motor driver controller kit.
♞【Application】This cnc kit are widely used in engraving machine, printer,....
♞【Stepper Motor】23HS2430B Nema23 57 stepper motor.
♞【Driver】CW5045 driver Voltage: DC 24-50V.
Current: rated maximum output reaches: ±4.5A.
♞【5 Axis Breakout Board】5 Axis breakout boad with cables,this breakout board needs to be connected to the parallel port and USB port of the....
♞【Power supply】400W,36V/9.7A switching power supply.

♞【Stepper Motor】4pcs 23HS2430B nema23 stepper motor.
♞【Stepper Motor Driver】4pcs CW5045 driver, current: 1.3A-4.5A.
Driver microstep: 1 (1.8°), 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/128, 1/256, 1/5,....
♞【Control Board】1pcs 5 Axis breakout boad with cables,this breakout board needs to be connected to the parallel port and USB port of the....
♞【Power supply】1pcs 400W,36V/9.7A switching power supply.
♞【Application】This cnc kit are widely used in engraving machine, printer, medical equipment, embroidery machine, stage lighting, textile....