Reviews Single Sheave Pulley

Mytee Products Snatch Block with Hook WLL 8 Ton 6 Sheave 3/4 Inch Wire Rope Wrecker Roll Back Recovery

  • The snatch block is a pulley system with covered and protected yet removable sides..
  • Snatch blocks or pulleys are used to change the direction of the pull to a different angle relative to a fixed point..
Check Stock

Martin 2517 1 1/2 Taper Bushing, Sintered Steel, Inch, 1.5\ Bore, 3.375\ OD, 1.75\ Length

  • Taper bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
  • Sintered steel for greater strength and resistance to wear than steel.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Interchangeable with taper bushings from various manufacturers.
Check Stock

Martin 1008 5/8 Taper Bushing, Sintered Steel, Inch, 0.62\ Bore, 1.386\ OD, 0.875\ Length

  • Taper bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
  • Sintered steel for greater strength and resistance to wear than steel.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Interchangeable with taper bushings from various manufacturers.
Check Stock

Martin 2517 2 7/16 Taper Bushing, Sintered Steel, Inch, 2.44\ Bore, 3.375\ OD, 1.75\ Length

  • Taper bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
  • Sintered steel for greater strength and resistance to wear than steel.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Interchangeable with taper bushings from various manufacturers.
Check Stock

Martin 2517 1 1/4 Taper Bushing, Sintered Steel, Inch, 1.25\ Bore, 3.375\ OD, 1.75\ Length

  • Taper bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
  • Sintered steel for greater strength and resistance to wear than steel.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Interchangeable with taper bushings from various manufacturers.
Check Stock

Martin 2012 1 5/8 Taper Bushing, Sintered Steel, Inch, 1.63\ Bore, 2.75\ OD, 1.25\ Length

  • Taper bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
  • Sintered steel for greater strength and resistance to wear than steel.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Interchangeable with taper bushings from various manufacturers.
Check Stock

Martin 2012 1 1/8 Taper Bushing, Sintered Steel, Inch, 1.13\ Bore, 2.75\ OD, 1.25\ Length

  • Taper bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
  • Sintered steel for greater strength and resistance to wear than steel.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Interchangeable with taper bushings from various manufacturers.
Check Stock

NewDoar Fixed Plate Micro Pulley,26KN CE Certified General Purpose Small Aluminum Rope Pulleys for Climbing/Aloft Work/Rappelling/Rescue Etc(26KN Red 2pcs)

  • [Specification] 1.77 inch(4.5cm)*3.2 inch(8.2cm),The maximum load up to 26kN /5848 lb,Net Weight:0.19Ib(90g),Sheave Diameter: 0.8 inch / 21 mm..
  • [Applicable Rope] Compatible with wide range of ropes up to 13 mm /0.5 inch, for complex rescue / hauling system setup..
  • [Durable] High-quality micro pulley which is the heart of a good doubled-rope climbing system.high durability to satisfy all your requirements, Light, compact and quick to install on the rope..
  • [Easy to carry] The Magnesium Aluminum Alloy Material is light yet durable.Weighs only :0.19Ib(90g),EN12278 CE 1019..
  • [Wide Application] This micro pulley excels great as well in many other applications, such as hauling, transporting or other mechanical advantages..
Check Stock

Mytee Products Snatch Block with Hook WLL 4 Ton 4 1/2\ Sheave 1/2 Inch Wire Rope Wrecker Roll Back Recovery

  • The snatch block is a pulley system with covered and protected yet removable sides..
  • Snatch blocks or pulleys are used to change the direction of the pull to a different angle relative to a fixed point..
Check Stock