Reviews Silent Stepper Motors

AOICRIE 5Pcs L298N Dual H Bridge Stepper Motor Driver Board For Arduino (5pcs)

【Package Included】- 2pcs L298N Motor Driver Controller Board Modules..
【Item Condition】- Drive voltage 5V-35V, high working power to 46V. Large current can reach 3A MAX and continue current is 2A. Power to 25w.(NOTE: To avoid damage, please use an external 5V logic supply when using more than 12V driving voltage.).
【High Quality】- Use L298N as the main driving chip, so the module has such features as strong driving ability, strong anti-interference and low calorific value. And it also use large-capacity filter capacitor and diode with freewheeling protection function, thereby improve the reliability of module..
【High Efficiency】- Dual-channel H-bridge design, can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors..
【Easy of Use】- No assembly required. This L298N board comes ready to go. Just wire up motors and power, this thing will work wonders..

THE LATEST GENERATION STEPPER MOTORS:Replacement for the older and faulty X27 168, X27-168, X25 168, xc5 168, x15 168, x25-168, xc5.168..
APPLICATION: For Instrument Panel,Gauge Cluster,Temp Gauge,Tachometer,Speedometer.
FITMENT:Compatible with Chevy Silverado, Suburban, Traiblazer, Tahoe,Avalanche,Impala,Monte Carlo,Malibu,SSR,Tracker,Venture.
WHY BUY THIS ITEM:Each gauge of your instrument cluster need one stepper motor.If your vehical easy to gauges dead, chatter, sticking,....
WHAT'S YOU GET:6Pcs Motors,10Pcs Backlight Bulbs.Easy to find a vedio on the internet..

Main driver chip L298N, strong driving ability, strong anti-interference, low calorific value, afterflow diode protection, more stable and reliable for Arduino projects.
Double H bridge design, can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors, high efficient.
No assembly required. This L298N board comes ready to go. Just wire up motors and power, easy to use.
External size 43*43*27mm / 1.69*1.69*1.06 inch, voltage 5V-35V, drive current 2A (Max single bridge).
Great for Arduino DIY Smart Car Robot Power UNO MEGA R3 Mega2560 Duemilanove. If driving voltage is more than 12V, please use external standard 5volt TTL outputs to switch the H-bridge circuits.

Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards, Jetson Nano.
Protection features: Overcurrent Protection (OCP), Thermal Shutdown (TSD), VM Undervoltage Lockout (UVLO).
Integrates 5V regulator, allows providing power to Raspberry Pi.
6 available microstepping modes, configured with the DIP switches: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step.
Adjustable motor drive current via potentiometer, maximum 2.5A current output.
Onboard dual DRV8825 motor controller IC with built-in microstepping indexer, drives two stepper motors, easy to use.
Onboard multi connector options for stepper motors in different specifications.

Single H bridge output current: 1.5A, can drive 2 DC geared motors..
Built-in overcurrent protection, short circuit protection, undervoltage lockout and overtemperature protection. With low power sleep mode..
For DIY smart car robot, it can drive DC motors up to 1.5A and 4-wire stepper motors..

This Stepper Motor HAT gives your Raspberry Pi the ability to drives two stepper motors at the same time, supports up to 1/32 microstepping..
Standard Raspberry Pi 40PIN GPIO extension header, compatible with Raspberry Pi Zero/Zero W/Zero WH/2B/3B/3B+/4B and later versions, Jetson Nano.
6 available microstepping modes, configured with the DIP switches: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step.
Applications: 3D Printer, Sculpturing machine, Mechanical arm.

4 H-Bridges: TB6612 chipset provides 1.2A per bridge with thermal shutdown protection, internal kickback protection diodes..
Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution).
Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil, interleaved or micro-stepping..
Big terminal block connectors to easily hook up wires (18-26AWG) and power.

This stepper motor driver lets you to operate bipolar stepper motors in full-, half-, quarter-, eighth-,and sixteenth-step modes, with an output drive....
There are no phase sequence tables, high frequency control lines, or complex interfaces to program..
The A4988 interface is an ideal fit for applications where a complex microprocessor is unavailable or is overburdened..
The translator is the key to the easy implementation of the A4988. Simply inputting one pulse on the STEP input drives the motor one microstep..
This product is a breakout board for Allegro¡¯s A4988 DMOS Microstepping Driver with Translator and Overcurrent Protection.

【Upgrade Black Extruder】All Metal MK-8 Extruder Feeder Drive 1.75mm Filament. It makes loading the filament easier and smoother, with no worries about filament scraping or breaking. This extruder feeder drive is compatible with nearly all models of 3D printers. No need to change stepper motors or other mounting hardware..
【Wide Application】The upgrade Creality3D silver metal Bowden extruder is compatible with nearly all models of 3D printers(Ender 3/3 Pro, Ender 3 V2, Ender 3 Max, Ender 5/5 Plus/5 Pro, CR-10, CR-10 V2, CR-10 Max, CR-10 S4, CR-10 S5, CR-10S, CR-10 Plus, CR-X, CR 20/20 Pro). No need to change stepper motors or other mounting hardware..
【Very Easy to Install】 Unbolt the old original Creality plastic extruder & screw in the new Metal Extruder and ready to start printing. Our metal extruder kit comes with an instruction on how to put it together, which makes it easier to install. Used for 1.75mm filament of 3D printer MK8 Bowden extruder frame.
【Durable】 All-metal aluminum alloy, DIY aluminum block and you need to be assembled by yourself. Giving a much smoother travel and print quality. Fits a 1.75mm filament..
【Official Creality Original Quality】This high-quality all-aluminum construction is guaranteed to last for years,....