Reviews Setting Potentiometer

Feedback Control

DUAL-CHANNEL - Connect up to 2x electric actuators with potentiometer feedback to have them travel in parallel, sequence, or individually.
SYNCHRONIZE - Connect devices with potentiometers to synchronize their movements.
SAVE UP TO 3 PRESETS - Use the wired remote to save 3x preset locations.
COMPATIBILITY - With a current rating of 15A, this control system is easy to use with a variety of 12VDC or 24VDC devices. Includes wire harness for each channel.
SPECIAL ATTENTION: Use it only with an actuator with potentiometer feedback. See at our Store PA-14P model..

DUAL-CHANNEL - Connect up to 2x electric actuators with potentiometer feedback to have them travel in parallel, sequence, or individually.
SYNCHRONIZE - Connect devices with potentiometers to synchronize their movements.
SAVE UP TO 3 PRESETS - Use the wired remote to save 3x preset locations.
COMPATIBILITY - With a current rating of 15A, this control system is easy to use with a variety of 12VDC or 24VDC devices. Includes wire harness for each channel.
SPECIAL ATTENTION: Use it only with an actuator with potentiometer feedback. See at our Store PA-14P model..

DUAL-CHANNEL - Connect up to 2x electric actuators with potentiometer feedback to have them travel in parallel, sequence, or individually.
SYNCHRONIZE - Connect devices with potentiometers to synchronize their movements.
SAVE UP TO 3 PRESETS - Use the wired remote to save 3x preset locations.
COMPATIBILITY - With a current rating of 15A, this control system is easy to use with a variety of 12VDC or 24VDC devices. Includes wire harness for each channel.
SPECIAL ATTENTION: Use it only with an actuator with potentiometer feedback. See at our Store PA-14P model..

...tube is used, the display unit is 1kHz, the photo has color difference, and the actual color is red. The working frequency covers 7.000-7.100mhz, 1kHz or 100Hz steps )..
Ta2003 mixer is used for reception, and crystal filter is used for if. After ta2003 multiplication detection, the sound size is adjusted by digital potentiometer and sent to audio active filter circuit. Finally, LM386 drives speaker, and if frequency supports calibration setting..
Use 3 bs170 parallel outputs, class E amplification, 12V power supply, output power 5W! Relay switching is used for transceiver, with the function of transmitting delay adjustment to avoid frequent relay switching and improve the isolation of transceiver channel..
It has the function of automatically sending call signs, which is very convenient to use. The MCU uses the original code of our store, which can adjust the code speed, sidetone frequency and sidetone size. It can input the call sign by itself (in automatic key mode) and support power down saving..
The PCB board of this kit can be conveniently put into the 88 * 30 * 120mm aluminum chassis (the shell needs to be prepared by itself, and the opening size of the front and rear panels is in the mesh disk). Main indicators Power supply: 12V Working current: ....

[ALPS 10KΩ Potentiometer] – The OEM trim pot resistor was made by ALPS. It fits ALPS analog joysticks. This trimmer potentiometer works with PS3, PS4 DualShock 4 series (PS4, Slim and Pro), Xbox One series (Xbox One, One S|X), Elite Series 1 and 2, and newest Xbox Series S|X. It’s also compatible with Nintendo Switch Pro and some 3rd party controllers like ‘Scuf’ and ‘Razer Raiju Ultimate’ with 10KΩ ALPS thumbstick module inside.
[Compatibility] – ALPS sensors come in two different resistance values. Make sure the value is around 10K ohm before ordering. Never judge its value by its color. (Be noticed: Choose 2.1KΩ version for PS5 DualSense and some rare PS4 controllers. ALPS version is not interchangeable with the orange version made by FU.).
[Additional Resistor] – Complicated moving mechanism and daily wear and tear finally caused drifting. Even new sensors cannot be 100% balanced. Calibrating in controller settings might not work. We packed 10x correction resistors to solve the potential problem in hardware level. Solder one or two paralleled tiny resistors onto the potentiometer at the opposite direction against drifting. It will help correct 3 to 5 degrees drifting.
[For most joystick problem] – The potentiometer sensor needs ....

Circuit wiring set for SSS SSH style Fender Squier Stratocaster electric guitar, material: metal and wire, switch cap: Black.
Wiring harness: 1 volume / 2 tones / 5 way switch, 2 capacitors, 1 output jack socket.
1 Volume and 2 Tone Knob Pots: Two A500k potentiometer, 1 B500k potentiometer.

DUAL-CHANNEL - Connect up to 2x electric actuators with potentiometer feedback to have them travel in parallel, sequence, or individually.
SYNCHRONIZE - Connect devices with potentiometers to synchronize their movements.
SAVE UP TO 3 PRESETS - Use the wired remote to save 3x preset locations.
COMPATIBILITY - With a current rating of 15A, this control system is easy to use with a variety of 12VDC or 24VDC devices. Includes wire harness for each channel.
SPECIAL ATTENTION: Use it only with an actuator with potentiometer feedback. See at our Store PA-14P model..