Reviews Servo To Multiplexer Board

MKS SERVO42C NEMA17 Closed Loop Stepper Motor Driver Low Noise for CNC 3D Printer Prevent Losing Steps Compatible with Gen L SGen L SKR 2 / V1.4 Turbo BTT Octopus V1.1 Mainboard

  • MKS servo42C is a product developed by MKS to meet market demand. The closed-loop motor uses the motor's rotation angle feedback to the drive circuit to detect whether every step that should be taken has been taken to prevent losing steps. If a closed loop occurs, the motor will make up or lose steps through the feedback information, and the blue LED on the closed loop module will light up..
  • Support 1-256 subdivision,odd subdivision (such as 11 subdivision) is also available. And support motors with 0.9 degree or 1.8 degree. Maximum speed 1000RPM. With usart interface, you can connect the computer by serial port, for parameter adjustment and query..
  • Position /speed/torque closed-loop, it can run at high speed without losing step. Easy to install and wire. The max printing speed can reach 150-180mm/S. Field-Oriented control, low noise, low vibration and low calorific. 4 Half bridge driver with 8 MOSFET, high operating efficiency. 14Bits magnetic encoder, high angle resolution..
  • Compatible with Gen L SGen L, SKR 2 / V1.4 Turbo BTT Octopus V1.1 Motherboard and other board which is seperated with drivers, that means drivers is not soldered onto the board.
  • Package: 1*MKS SERVO42C(include motor) + 1*Adapter board(MKS APT) + 1*60cm 6pin Data Cable . (User metho....
Check Stock

12Pcs CD74HC4067 16-Channel Analog Digital Multiplexer MUX Breakout Board Module CD74HC4067 CMOS Precise Module Compatible with DIY

  • CD74HC4067 board for the very handy 16-Channel Analog/Digital Multiplexer/Demultiplexer, use the CD74HC4067 16-channel analog signal switch.
  • It works with both digital and analog signals (the voltage can’t be higher than VCC), and the connections function in either direction.If you want two-way communications,you can add a second board to route your microcontroller's TX line to 16 device's RX lines. By using multiple boards, you can create similar arrangements for I2C,SPI,etc..
  • The internal switches are bidirectional, support voltages between ground and VCC, have low “on” resistance and low “off” leakage, and to prevent crosstalk, perform “break-before-make” switching. The board also breaks out the chip’s “enable” pin, which when driven high, will completely disconnect the common pin (all switches “off”)..
  • To control it, connect 4 digital outputs to the chip’s address select pins (S0-S3), and send it the binary address of the channel you want. This allows you to connect up to 16 sensors to your system using only 5 pins..
  • Since the mux/demux also works with digital signals, you can use it to pipe TTL level serial data to or from multiple devi....
Check Stock

Barnabas Robotics Servo Motor Tester Kit | 180 Degree 9g Servo Motor + RC Servo Tester Controller + 6V Battery Holder

  • [CONVENIENT, ALL-IN-ONE KIT FOR TESTING SERVO MOTORS] Experiment with servo motors with this all-inclusive kit. Includes 9g servo motor + servo tester controller + 6V battery holder at a low price!.
  • [9G Servo Motor] 180 degree range of motion. Includes 3 types of servo horns..
  • [4 CELL x AA BATTERY HOLDER] Fits 4 x AA batteries, which produces 6V for your servo tester and servo motors..
  • [SERVO TESTER] Includes 3 modes to test servo motors or ESC.
  • [GREAT FOR RC APPLICATIONS] Use as a power source for robotics, RC cars, helicopters, planes, boats and or any hobby projects.
Check Stock

100PCS CD4053 CD4053B CD4053BE DIP-16 Analog Multiplexer IC

  • It is suitable for digital and analog signals (voltage cannot be higher than VCC) and can be connected in either direction. To control this, please connect the four digital outputs to the address selection pin of the chip (SO-S3) and send it the binary address of the desired channel..
  • The internal switch is bidirectional, with a low on resistance and off leakage, and to prevent talk, please turn off the switch first and then on..
  • Drive it to a high level, and it will completely disconnect the common pins (all switches are disconnected)..
  • This is a very convenient 16 channel CD74HC4067 analog/digital multiplexer/demultiplexer..
  • Because the multiplexer can also process digital signals, you can use it to transfer TTL-level serial data to multiple devices through pipe or transfer from multiple devices..
Check Stock

WEISHUJI 10PCS 25T Aluminum Servo Horns Arms, M3 Threads Metal Steering Arm for Towerpro, HSP, HD power, Futaba, Axial, Savox, Xcore, Standard Servos Motors, MG995 MG996R MG946R, S3003 etc servo (Red)

  • 25T Aluminum Servo Horns Arms are suitable for mostly 25T Standard Servo Motor, and M3 Threads Metal Steering Arm is compatible with Towerpro HSP HD power Futaba Axial Savox Xcore Standard Servos Motors MG995 MG996R MG946R S3003 etc servo..
  • 25T Aluminum Servo Horns Arms are made of strong aluminum, 25T Aluminum Servo Horns M3 Threads are hard to break..
  • 25T Aluminum Servo Horns Arms are of dimension 35x15x6mm, and Metal Steering Arm behaves very well on your RC models..
  • 25T Aluminum Servo Horns Arms are djustable type servo arm, and M3 Threads Metal Steering Arm have two steel bolts to secure the split-clamp onto the servo output..
  • Package of 25T Aluminum Servo Horns Arms include: 10 x 25T Aluminum Servo Horn-Red, M3 Threads Metal Steering Arm, 25T Aluminum Servo Horns M3 Threads some hardware.
Check Stock

Analog Multiplexer Single 8:1 ñ9 Volt 20 Volt 16-Pin Plastic DIP Tube

  • The internal switch is bidirectional, with a low on resistance and off leakage, and to prevent talk, please turn off the switch first and then on..
  • It is suitable for digital and analog signals (voltage cannot be higher than VCC) and can be connected in either direction. To control this, please connect the four digital outputs to the address selection pin of the chip (SO-S3) and send it the binary address of the desired channel..
  • Drive it to a high level, and it will completely disconnect the common pins (all switches are disconnected)..
  • Because the multiplexer can also process digital signals, you can use it to transfer TTL-level serial data to multiple devices through pipe or transfer from multiple devices..
  • This is a very convenient 16 channel CD74HC4067 analog/digital multiplexer/demultiplexer..
Check Stock

MACH3 Controller USB MACH3 100Khz Motion Controller Card Breakout Board Controller Card for CNC Engraving Servo Motor Stepper Motor Servo motor

  • 【Functions】The function of this motion control card includes that it supports automatic probe tool, emergency input, limit switch, and supports....
  • 【4-axis Linkage】Usb interface board supports for 4-axis linkage, you can connect four stepper motor drives or servo drives. 4 general-purpose....
  • 【Wide Use】The maximum step-pulse frequency of motion control card is100KHz, which is very suitable for CNC Engraving, Servo Motor, Stepper Motor....
  • 【Advantage】The motion controller needs using external 24V DC power to isolate USB and external port, and to make the system more stable. And it....
  • 【Drive Output Interface】The 4 general-purpose isolated relay drive output interface can drive four relays for controlling the spindle starts,....
Check Stock

OSOYOO Robot Rc Smart Car DIY Kit to Build for Adults Teens with Servo Power Steering Motor, WiFi, Bluetooth, Code Programmable Compatible with Arduino UNO

  • Most Advanced Technology in the Market Today: the OSOYOO Robot Car kit features a servo power steering motor that controls the axles to turn the wheels. This electric power steering system enables a highly automated driving experience that imitates real-world full-sized vehicles.
  • Do-it-yourself Starter Robot Car Building Kit: allows adults, teens, and all students to learn valuable skills, fully compatible with Arduino UNO R3 board, it will help you learn about electronic circuits, programming sensors and actuators, the Internet of Things (IoT), coding, electronics, mechanical engineering and hands-on experience in robotics.
  • Package includes all the technical modules, parts, and sensors you need to build a fully functional robotic car: such as MCU board for R3, OSOYOO motor shield, OSOYOO ESP8266 WIFI shield, HC Bluetooth module, line tracking module, ultrasonic sensor, micro servo motor, battery, and charger.
  • Multifunctional and features all the highly advanced intelligent features and driving modes that you expect for a robot car: which includes: auto-go, line tracking, ultrasonic avoidance, Wifi IOT control, Bluetooth App control, compatible with Android and Apple IOS devices via an app developed in house exclusively for OSOYOO.
Check Stock

TecUnite 20 Pieces 3-Pin Extension Cable Cord Female to Male Wire Connectors for Servo Extension Connection Control Board Remote Control Parts(4 Sizes)

  • Servo extension cord sizes: have 4 different lengths of 10 cm/ 3.94 inch, 15 cm/ 5.9 inch, 30 cm/ 11.8 inch and 50 cm/ 19.7 inch, each length has 5 pieces servo extension cords.
  • Application: these servo extension leads are compatible with Futaba and JR servo, plane and helicopter servo connection or receiver connection, remote control car, RC Car.
  • 3-Pin servo extension wire: each servo extension has 3 pieces of 0.08TS wires, universal model.
  • Connectors with 3 pins and have an angle in case you will install incorrectly, convenient for use.
  • Female to male servo extension cable: featured with female connector on one side and male connector on the other side, can be connected to the receiving set and steering engine.
  • Package includes: 20 pieces of female to male servo extension cable wires with 4 different lengths, enough for you to use on different occasions.
Check Stock