Reviews Sensor Module

Acxico 2Sets Laser Sensor Module For Arduino AVR(KY-008 Laser Transmitter +Laser Receiver Sensor Module Non-modulator Tube)

Model: 1*Laser Receiver Sensor Module+ 1* KY-008 Laser Transmitter Module.
Laser Receiver Sensor Module uses the non modulated laser receiver, please use in the room where without the light, the sunlight or other lamps and lanterns will interfere, suggested in the dark environment use..

Simplify connecting a waterproof temperature sensor to your project with this adapter module kit.
Pull-up resistor included on the adapter module, an external resistor is not required to connect directly to the GPIO of the Raspberry Pi.
Waterproof digital temperature sensor DS18B20 on 100cm cable with adapter module.
Measure the temperature directly in water or soil.
DS18B20 Wiring: Red = VCC, Yellow = Data, Black = GND.

This RCWL-0516 module has the characteristics of high sensitivity, high induction distance, high reliability, large induction angle, wide power supply voltage range, etc. it is widely used in various kinds of human body induction lighting and alarm and so on..
Compatible with Arduino Raspberry PI,Human Rat Cat Detector for nodemcu for wemos etc..
It also can detect human, cat, rat, water.
Wide operating voltage range: 4.0-28.0V, output 3.3V power supply.
RCWL-0516 RCWL 0516 Microwave Radar Sensor Human Sensor Body Sensor Module.
What you will get: 12pcs RCWL-0516 Module, 40 pins header.

This ir transmitter sensor module is directly launched by a single tube, it requires waveform modulation through the program..
It is suitable for infrared communication, infrared remote control, apply to a variety of platforms including for Arduino/51/AVR/ARM.
With signal indicating LED, easy to observe and debug..
Pin Definitions: (1) Output (2) Vcc (3) GND.
IR Infrared Transmitter Module Ir Digital 38khz Infrared Receiver Sensor Module For Arduino Electronic Building Block.

Communication: standard IIC communication protocol.
✹✹This sensor module is a small, 3 a-xis accelerometer and 3 ax-is gyroscope integrated in a single package..
✹✹The BMI160 is a small, low-power, low-noise 16-bit inertial measurement unit designed for use in mobile applications such as augmented reality or inland navigation, which require high-precision, real-time sensor data..
✹✹In full operation mode, with both the accelerometer and gyroscope enabled, allowing always-on applications in battery-powered devices..
✹✹3PCS 6DOF Bosch GY-BMI160 Module 6-axis Acceleration Gyro Gravity Sensor for Arduino.

Received great ideas from our customers and adopted in this upgraded kit. Removed useless modules heartbeat sensor, two of the hall sensors, one of the dual-color sensor. Add useful modules like GY-521 accelerometer module, LCD1602 screen, DS1307 real time clock module etc..
Professional 37-in-1 Sensor Module Kit, NOT ONLY compatible for BUT ALSO compatible for raspberry pi RPi 3 2 Model B A A+ B+, Complete Update and common models for Mega 2560 starter kit..
Standard interface can be controlled directly by microcontroller ( 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic)..
Upgraded tutorial only for R3, for MEGA2560 R3, for NANO in CD, listing paper, resistors pack only from Elegoo Team. There are tutorials in the CD that comes with. or download the tutorials online from the official website..
100% compatible with Arduino official IDE, Raspberry Pi and STM32..

INA219 module is an I2C interface with a drift, bi-directional current / power monitor integrated circuit (IC), and further expand the energy-saving....
INA219 I2C Bi-directional DC Current Power Supply Sensor, Working Voltage 3~5V.
INA219 module small size, low cost, high accuracy. It not only can monitor the voltage drop across a shunt resistor on the sensing shunt supply....
INA219 can be achieved within the maximum error accuracy of +1% from -40° C to 85° C temperature range, the maximum offset is 100 uV. The....
Appliaction:The module is used for I2C port zero drift / bidirectional current / power monitoring sensor module. The device is available in a SOT23....

Load cell-This load sensor, sometimes called a strain gauge, is the same one found in digital bathroom scales (you know, the ones you use in January for your New Year’s resolutions, and then forget about a month later)..
HX711-This module uses 24 high precision A/D converter chip hx711. It is a specially designed for the high precision electronic scale designwith two analog input channelthe internal integration of 128 times the programmable gain amplifier. The input circuit can be configured to provide a bridge type pressure bridge (such as pressureweighing sensor mode)is of high precisionlow cost is an ideal sampling front-end module..
Hx711 SPECS-Selectable 10SPS or 80SPS output data rate.
Operation supply voltage range: 2.6 ~ 5.5V.
Package:4 x human scale load cell sensor.

Hands-free operation for a more hygienic bathroom experience.
Place hand 1-1/2 in. from sensor for 2 seconds to trigger flush.
Requires a Cadet bowl, sold separately, see below.
Requires Cadet bowl 3517A101 or Cadet bowl with seat 3075000, sold separately.
Promotes a cleaner bathroom and more hygienic experience.Sensor module detects hand proximity and flushes toilet automatically.To activate the touchless flush, simply position hand within 1-½ in. over sensor face for approximately two seconds to trigger a powerful flush.Compact, 2-½ in. sensor module can be installed on wall within 3 feet of toilet or on top of toilet tank.To activate the manual flush option, ensuring continual operation in the event batteries need replacing, simply push and hold the actuator button for approximately two seconds.Powerful Cadet flushing system ensures everyday dependability.