Reviews Power Supplying Module

BIQU Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer

A general add-on heated bed power expansion module for 3D printer.
Completely solve the hot bed power is too large and the load current issue. It can work with the Anet A8.
With this addon module to your 3D printer motherboard you can lead the maximum current up to 15A.
Under the premise of normal heat dissipation, this module can work steadily under the condition of I(Max)=15A. Don't exceed 15A during the process.).
If you intend to use heated bed with your 3D printer that uses a 12V power supply, then this module is recommended, else it may cause excessive....

Model specific. NOT universal. Alternate part numbers include AP3768578, 1055597, 75304440031, AH979525, EA979525, and PS979525..
This 2 1/4 inch long incandescent bulb features a small screw-in base..
It is important to disconnect your appliance from the power supply before servicing..
Supplying Demand replacement parts are compatible with Major Brands, but you should always verify fitment with your specific model. We have included a....
SD products come in Supplying Demand packaging that includes helpful information should you have any issues..

Alternate part numbers include AP4444552 and PS4144665..
Includes (1) black caster wheel |1.5 inch diameter | 1 inch wide | Fits model specific side-by-side refrigerators | This caster is located on the....
It is important to disconnect your appliance from the power supply before servicing..
Supplying Demand replacement parts are compatible with Major Brands, but you should always verify fitment with your specific model. We have included a....
SD products come in Supplying Demand packaging that includes helpful information should you have any issues..

How to install: please check the product pictures carefully for the wiring diagram steps before using, simple dual-panel design and the input output using the 3 pin single row pin for easy connection, the input voltage is higher than output voltage 1.2V, the module will work normally.
AMS1117-3.3 is a positive voltage regulator step down power supply module, support DC 4.75-12V input and 3.3V fixed voltage and 0.8A current output.
Electronic devices partner: the 3 pins AMS1117-3.3 voltage regulator mini step down power supply module, can be applied to electronic devices which need 3.3V power supply, such as SCM project design, MCU development and more, easy to be connected and provide the power supply.
Where to use: the voltage to 3.3V 800mA DC buck module is applicable for high-efficiency linear regulator published active power regulator battery charger active instrument.
Compatible with: the 3 pins AMS1117-3.3 voltage regulator mini power supply is compatible with Arduino MEGA2560, MSP430 development board, 3.3V low power consumption MCU, FPGA/CPLD PLD programmable logic systems, ARM7 ARM9 ARM11 STM32, etc..
Provide more safety: the AMS1117-3.3 800mA DC buck module features overheat shutdown circuit provides overload and over-temperature protectio....

Alternate part numbers include WP2182179, AP6005980, 450120, and WP2182179VP. Screws not included..
This cam mounts to the bottom of your refrigerator or freezer door and helps maintain position when opening or closing the door. IT is advised to....
It is important to disconnect your appliance from the power supply before servicing..
Supplying Demand replacement parts are compatible with Major Brands, but you should always verify fitment with your specific model. We have included a....
SD products come in Supplying Demand packaging that includes helpful information should you have any issues..

This is the "momentary" variety of the touch sensor - touch and it turns on, release and it turns off..
Positive and negative can be used as a touch surface,can replace the traditional touch button..
Four M2 screws positioning holes for easy installation.Module can be installed in such as surface plastic, glass of non-metallic materials..
In addition to the thin paper ( non-metallic ) covering the surface of the module , as long as the correct location of the touch , you can make hidden in the walls, desktops and other parts of buttons..
The module is based on a touch-sensing IC (TTP223B) capacitive touch switch module. In the normal state, the module output low, low power consumption.
When a finger touches the corresponding position, the module output high, if not touched for 12 seconds, switch to low-power mode..

Model specific. NOT universal. Alternate part numbers include AP4420263, 201657035, 201657-03S, 20165702, 20165703, 41602, and 767A-378..
This is a single silicone nitride hot surface ignitor measuring approximately 8 x 1.25 x 0.75 inches. It can be used in HVAC gas ignition controls..
It is important to disconnect your appliance from the power and gas supply before servicing..
Supplying Demand replacement parts are compatible with Major Brands, but you should always verify fitment with your specific model..
SD products come in Supplying Demand packaging that includes helpful information should you have any issues..

Alternate part numbers include 131268200, 134560400, 134560410, 134999000, 134999010, 2220542, 5304467357, AH3508101, EA3508101, and PS3508101..
Comes with 2 shocks, 4 bolts, 1 plug, and directions..
It is important to disconnect your washing machine from the power and water supply before servicing..
Supplying Demand replacement parts are compatible with Major Brands, but you should always verify fitment with your specific model. We have included a video in the product gallery to help you find your model number and information in the description below..
SD products come in Supplying Demand packaging that includes helpful information should you have any issues..

Alternate part numbers include WPW10185972, AP6016537, 1481701, PS11749827, and WPW10185972VP..
220VAC | 60Hz | 1/36 RPM | CW rotation | 3W | This timer will be unable to advance its cycle if the dryer does not heat as intended..
It is important to disconnect your appliance from the power supply before servicing..
Supplying Demand replacement parts are compatible with Major Brands, but you should always verify fitment with your specific model. We have included a....
SD products come in Supplying Demand packaging that includes helpful information should you have any issues..