Reviews Pinch Weld Jack Adapter

ABN Scissor Jack Adapter - 1.5in Square Drive Drill Scissor Jack Connector to Raise Lower and Level Your Vehicle

[Swap Tires Faster]: Quickly remove flat tires with ABN Scissor Jack Drill Adapter.
With minimal force, you can raise, lower, and level your scissor....
[How to use]: Slide drill jack adapter onto the scissor jack and stick the bolt and washer through the predrilled holes of the adaptor and jack.
[Pro Safety Tips]: Store a scissor jack and drill car jack adapter in your trunk in case of emergencies.
Always ensure you are on a flat surface when....
[Use Existing Tools]: Fits “U” shaped and “O” shaped scissor jacks.
Adapter scissor jack tool is compatible with 1/2" drive/impact....
[Quality You Can Trust]: Heavy-duty chrome vanadium steel coating resists elements so you can change tires in any weather.

Trailer Tongue Vertical Channel Style Weld On Adapter for Trailer A-Frame. Trailer Tongue Vertical Channel Style Weld On Adapter for Trailer A-Frame..
Equipped with 6 Adjustment Holes. Raw Steel. The six bolt hole pattern works great with typical vertical channel bolt on trailer couplers. Actual vertical channel is 3-1/2" x 11-3/4" w/ 2" on center bolt pattern.
The outer front is 4" wide, the outer rear is 11" wide. From front to back it measures 7-1/2". Weight Rating: If you are using 2 bolts to attach coupler then its 14,000 lbs if using 4 bolts then 20,000 lbs that also assumes this kit is properly weld onto the trailer and the coupler you are using can handle those respective capacities..
Allows you to convert your trailer a-frame to one that accepts Vertical Channel couplers. Welding required for installation..
3 Style to choose from - Completely Welded, Spot Welded & Components Only (2 Sides,Base & Vertical Channel). Made in the USA by Shocker Hitch - Arthur, ND.

Controlled compressibility allows easy installation yet will not squeeze out or allow light to contact pinch weld. Sufficient material to replace one windshield or backlight..

High Quality Floor Jack Pad:Made of heavy duty construction rubber material,MAXIMUM Load Bearing: 3 Ton.
Nice design Rubber Jack Pad:There is a slotted crossline on the top of the jack pads, which can align with the side clip weld and protect the side, so as to prevent the frame longitudinal beam from bending when lifting the vehicle with the jack.
Standard size:Universal Floor Jack Rubber Pad for most vehicles.please verify dimensions and ensure fitment to your vehicle.
Warm Tips: Because of floor jack rubber pad is newly factory production and heavy duty rubber material, so this jack rubber pad will has a little bit rubber smell, please put it in the ventilation room for some while! Please do not mind it.
100 percent exchange or money refund- we are very sure that you will like our floor jack pad. Just contact us if not satisfied, we will be happy to help you and 100 percent replacement or full refund.

★Receiver Size: This trailer hitch receiver tube has 2 inch by 2 inch industry-standard fit.
★The weld-on hitch receiver is with 6 inch of total length.
★The tow hitch receiver tube is ready to Weld, with Raw Steel Finish.
★The weld-on trailer hitch tube is with 5/8 Inch Pre-drilled Hitch Pin Hole.
★This receiver hitch adapter can be used for custom welding project.

★Butyl Sealant Main Application: Butyl rubber tape is suitable for the shock-absorbing paste of windshield, door waterproof film,decorative parts,car lamp,bus body and frame,as well as the sealing of body seam and flange plate.
★Excellent Sealing: Our Butyl rubber sealant features excellent sealing adhesion,butyl tape can be sticky to any type of metal, concrete,glass,plastics and porous surfaces,no worries for falling off. Easy installation and removal.
★Easy To Use: Simply release the butyl sealant from paper and press it sufficiently around the pinch weld.And after removing headlamp cover, the weld areas should be dry,clean,free from dust,oil and grease.Butyl rope prevent leakage,corrosion,deformation,vibration, weather and aging. Non-toxic, tasteless, pollution-free, easy to use.
★Black Butyl Tape: Rubber Sealant is a non-drying,non-hardening synthetic rubber based butyl rubber sealant. It will remain permanently sealing and waterproofing,high viscosity,elasticity and tightness.
★Butyl Windshield Sealant Size: Butyl sealant Diameter: 9mm, Length: about 4 meters. It is long enough for re-sealing about 2 or 4 headlight assemblies, easy to cut to fit for your need.

Butt Welding Clamps includes 16 welding corner square welder clamps.
Used to make precision butt welds and edge-to-edge welds for patch repairs in floors, wings, door skins, fabricating, and re-skinning projects.
Use the Toolly Welding Square Clamp Set to pinch sheet metal panels level to each other.
While these metal clamps hold panels edge to edge with a 1mm gap, you can quickly weld the sheets together.
Each welding square tool pipe clamp can extend the clamp block to provide a .4-inch (1cm) tall gap.
Fits 3/16-inch to 26 gauge sheet metal materials.
Loosen the winged nut from the alignment screw then wedge two panels across from each other between the square body and the clamp block.
Tighten the winged nut to ensure a secure hold.
Use all 16 clamps for larger projects, then joint weld between them.

DEPENDABLE STRENGTH. This trailer jack is rated to support up to 5,000 pounds trailer tongue weight.
SWIVEL DESIGN. To ensure plenty of clearance while towing your trailer, this trailer jack stand is equipped with a swivel bracket. The jack swings up and out of the way for towing and features a pull pin to securely lock into place.
EASY OPERATION. This trailer tongue jack allows for 15 inches of vertical movement and operates using a top-wind handle (16-1/2-inch retracted height, 31-1/2-inch extended height). The integrated grip allows for easy raising and lowering.
CORROSION-RESISTANT. For long-lasting corrosion resistance against water, dirt, road salt and more, this trailer jack is protected in a durable black powder coat and zinc-plated finish.
SECURE INSTALL. This trailer tongue jack is designed to mount onto the trailer frame with a weld-on installation. It comes with a raw steel pipe bracket for ready welding.