Reviews Pcb Battery Clip

XBERSTAR 2PCS-3S 12.6V 18650 Lithium Battery Charger Protection Board PCB BMS Cell 40A Module

Enhanced version:Suitable for electric drill with starting current below 80A and power below 130W .(without balanced function).
3S 12.6V 40A lithium battery protection board.
Scope: Nominal voltage of 3.7V, lithium battery full of voltage 4.2V , including 18650,26650, polymer lithium battery.
Suitable for starting current below 80A, power 170W below the drill，Balanced version with balanced charging..
Package include:2 x PCB BMS Protection Board.

Type: 1pc ESD Wrist Strap, Color: Black, Width: 1.9cm, Length: 21cm, Twisted Cable Length: 1.8m, Surface Resistance: Below 1*105, Current Limiting....
Consist of elastic band, movable buckle, spring cable, protective resistor, banana plug and alligator clip..
Ground yourself while working on sensitive electronics, and protect your computer from electrostatic discharge damage when you are installing or....
Just wear the adjustable strap around your wrist and clamp the alligator clip to a grounded source. Convenient to operate..
Suitable for LCD/LED touch screen, electronic communication, electronic manufacture, electronic instrument and PCB projects and so on..

✔ Battery Specs：Capacity: 10050mAh / Lithium-ion / Voltage: 7.4V / Come with CE, FCC, PSE, ROHS Certified. Tested by manufacturer to match OEM....
✔ Smart LCD Display Screen：Intelligent LCD display indicator show the battery power level. It's convenient to check the remaining capacity. Touch....
✔ Multifunctional Battery Pack ：It can be charged with micro usb and type-c cables via 5V/2A USB power source directly without f970 battery....
✔ Widely Compatible with Devices：Work with the devices which takes Sony NP-F series mount batteries, such as Sony cameras and Handycam camcorders,....
✔ No Memory Effect：Powerextra NP-F Battery is combined with the newest generation of CPU control, IC chip, double PCB panel to deliver super power....

Pay attention:It's not A battery, it's 4/3A (same diameter but 4/3 height of A battery)also they are not 18650 batteries,pls make sure the size is....
Battery without PCB protected,also they are NIMH Battery can't replaced for 3.7V Battery.
No memory effect - batteries can be recharged when fully, or partially discharged.
Camera. 2.lights, model aircraft, miner's lamp, safety helmets, safety headlights.

[2022 UPGRADED HW V3.6] NEW HW VERSION: V3.6 with MicroSD card port now can have the measurement data or the screenshots saved in the it at anytime. Added battery circuit management, more secure. Redesigned PCB, you can connect to mobile phone with Type C-Type C cable( original PCB needs OTG cable), see a clear HD image on your phone. Added a case, which is protective and dust-proof. Disply: 2.8 inch TFT (320 x240).
[IMPROVED FREQUENCY ALGORITHM: The improved frequency algorithm can use the odd harmonic extension of si5351 to support the measurement frequency up to 1.5GHz. The 50K-300MHz frequency range of the si5351 direct output provides better than 70dB dynamic, The extended 300M-900MHz band provides better than 60dB of dynamics, and the 900M-1.5GHz band is better than 40dB of dynamics.
[MULTIPLE FUNCTIONS] The default firmware main function is used for antenna performance measurement. The TX/RX method can measure the complete S11 and S21 parameters. If you need to obtain S12 and S22, you need to manually replace the transceiver port wiring. Designed a practical and simple control application on PC, you can download touchstone(SNP) files for radio design and simulation software.
[STRONG AND SECURE POWER SUPPLY] This VNA is battery powered or USB powe....

Original Sanwa Denshi TP-MA Replacement PCB with Microswitches.
Replacement microswitch PCB for Sanwa JLF series Joysticks.
Often the PCB is the first to go out on a Sanwa JLF in a few years. Restore it to brand new by getting the Sawa TP-MA PCB assembly. This replaces the entire set of microswitches and PCB, and housed in very easy to install module..
Installation: Remove the Sanwa JLF lever restricted Remove the TP-MA board that comes from the Sanwa JLF lever Place the new board pointing in the same direction as the previous one. Finally place the restrict again.
Package include One pcs Original Sanwa TP-MA PCB with Microswitch.

2 in 1 lipo battery parallel charging board lipo charger,supporting XT60 connector and XT30 conector lipo battery.It is just a parallel charging board, not a diret charger, need to connect with a charger which support the balance port ( JST connector).
Thicken PCB copper foil, allow security using 35A charging current..
This lipo balance charging board supports up to four packs of the same type, same cells 2S-6S lipo battery pack,such as 2S lipo battery,3S lipo battery ,4S lipo battery,5S lipo battery,6S lipo battery..
Equipped with 40A fuse between any two groups of batteries, to prevent line burned due to the large battery pressure.
Output Connector:XT30 connector /XT60 connector,support xt30 and xt60 lipo batteries..

1000W continuous 2000W peak true pure sine wave power inverter, as good as grid power, power backup for home power supply..
Transfer 24VDC to 110V~120VAC, 60Hz frequency, US outlets. Intelligent temperature control cooling fan. Earth connection for both PCB board and output. Digital LCD display..
High quality true copper inductance, filter the wave form, ensure the true pure sine wave AC output, safeguard your equipment. All big imported mosfets with strong driving capacity..
Thick PCB, allow the stronger current floating on the circuit, increase the load capacity. High frequency transformer to transfer DC to AC, ensure the stable and full AC output.
Free standard battery cables ( 55cm length ) and spare fuse for replacement..

XT90 2-8S parallel charging board Support 6 packs 2S Lipo Battery, 6 packs 3S Lipo Battery, 6 packs 4S Lipo Battery, 6 packs 5S Lipo Battery, 6 packs 6S Lipo Battery,6 packs 7S Lipo Battery,6 packs 8S Lipo Battery.
Balanced port output line with 22AWG multi-strand silicone line..
Thicken PCB copper foil, allow security using 40A charging current.Equipped with 40A fuse between any two groups of batteries, to prevent line burned due to the large battery pressure..
There is 1.1A PTC fuse of each balance channel for safety..It can used with 6S,8S,10S balance chargers of XT60 main charge port or Banana port..
Fuse bracket new design：If fuse broken，it can be replace with a new one easily.