Class A Customs | T-4000-BPK| 40 Gallon Fresh Water Tank & Plumbing Kit RV Concession
- 40 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage.
- WATER TANK MEASUREMENTS: 39 1/2” Longest Length (not including fittings) x 13” x 18” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
- TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
- NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
- BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male Pipe....
Check Stock
Class A Customs | T-2300 | One (1) RV Fresh Water 23 Gallon Tank, Grey Water
- 23 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage.
- WATER TANK MEASUREMENTS: 39 1/2” Longest Length (not including fittings) x 8 3/4" x 14 3/4" - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
- TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
- NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
- Great extra water storage in RV, pop-up camper, off-road vehicles, concession trailers, hot dog carts, smaller food vendors and portable hand washing sinks. Class A Customs Manufactures this item in the USA in Elkhar....
Check StockEVIL ENERGY 6AN Swivel Hose End Fitting Straight for Braided CPE Fuel Hose Blue&Red 2PCS
- Please attention that 6AN straight fitting only be worked with Braided CPE fuel line. It can not be installed on PTFE Hose..
- Thread Size of 6AN hose fitting is 9/16-18UNF and the braided CPE fuel line which works with should be 3/8"..
- Swivel design for easy assembly, the adjustable AN wrench is highly recommended..
- Package Inclued: 2 pcs x 6AN straight swivel hose ends.
- EVIL ENERGY Provide different kinds of fuel fittings, Swivel, Push-on lock, PTFE hose end and other fitting adapters..
Check Stock
Class A Customs | T-3000-BPK| 30 Gallon Fresh Water Tank & Plumbing Kit RV Concession
- 30 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage.
- WATER TANK MEASUREMENTS: 34 1/2” Longest Length (not including fittings) x 12” x 17 1/2” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
- TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
- NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
- BASIC PLUMBING KIT INCLUDES - (TWO) 0.5” Hose Barb to 0.5” Male Pipe Thread Adaptor (FOUR) 0.5” Hose Clamp (ONE) 1.25” Hose Barb to 1.5” Male Pipe Thread Adaptor (TWO) 1.5” Hose Clamps (ONE) 1.5” Male ....
Check Stock
Class A Customs | 42 Gallon RV Concession Fresh and Gray Water Holding Tank | T-4200
- 42 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage.
- WATER TANK MEASUREMENTS: 27.5” Longest Length (not including fittings) x 15.25” x 22.5” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
- TANK BUILT-IN FITTINGS: (THREE) 1.5" Female NPT Fitting - fitting is sealed and watertight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT over-tighten fitting damage will occur, use plastic connecting fittings as metal will damage threads..
- NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
- Great extra water storage in RV, pop-up camper, off-road vehicles, concession trailers, hot dog carts, smaller food vendors and portable hand washing sinks. Class A Customs Manufactures this item in the USA in Elkh....
Check Stock
Class A Customs | T-2000 | One (1) RV Fresh Water 20 Gallon Tank, Grey Water
- 20 Gallon Fresh or Gray Water Holding Tank Manufactured by Class A Customs - Made from NSF Approved Materials - Fresh & Drinking Water Safe - Can be used for Fresh or Gray Water Storage.
- WATER TANK MEASUREMENTS: 32.5” Longest Length (not including fittings) x 11.75” x 11.75” - Tank can sit on any side - rotate tank to change height or width Average Thickness 7/32” +/- Please view photos. (Due to the manufacturing process +/- .25" on each measurement).
- TANK BUILT-IN FITTINGS: (TWO) 1.5" Female NPT Fitting - fitting is sealed and water-tight, to use remove membrane with razor knife (TWO) .5" Female NPT Fitting - fitting is open DO NOT Over-tighten fitting damage will occur – Use plastic threaded fittings, metal threads may damage tank fittings.
- NON-PRESSURIZED TANK: tank must be vented allowing air in and out during use. DO NOT make a sealed connection with a garden hose directly to tank, this is a pressurized connection and will cause tank to explode causing damage. For filling tank it is recommended to use a fill dish or other gravity process..
- Great extra water storage in RV, pop-up camper, off-road vehicles, concession trailers, hot dog carts, smaller food vendors and portable hand washing sinks. Class A Customs Manufactures this item in the ....
Check StockEVIL ENERGY 6AN PTFE Hose End Fitting 90 Degree Black for PTFE Hose Only
- Please Attention that the 6AN PTFE hose end can be work with PTFE fuel line ONLY..
- Thread Size of 6AN PTFE Fitting is 9/16-18UNF and work with PTFE fuel line(Hose ID: 0.31 inch OD: 0.43-0.47 inch)..
- The PTFE hose end is reusable, just replace a new ferrule if you reinstall the fitting..
- EVIL ENERGY Provide plently kind of fuel fittings, Swivel, push-on lock, PTFE hose end and other fitting adapters..
- Warrany: EVIL ENERGY provide PTFE hose end 6-month warranty. We value your shopping experience and strive to offer a high-quality product and service..
Check StockMars 11917
- Panel-mounted, barbed fitting allows tube connection on the side of a barrier.
- Fitting connects to tubing on one end and a female connector on the other.
- Acetal copolymer plastic for low moisture absorption and high tensile and flexural strength.
- Buna-N O-ring elastomer seal for long cycle life and repeatable, leak-free connection.
- Single-barb for increased pull-off resistance compared to three-barb styles.
Check StockLisle 19700 Valve Holder black
- Commonly used when valve springs or valve stem seals are replaced.
- Comes with two-step fitting for both 14 millimeter and 18 millimeter threads.
- Thread fitting to spark plug hole and other end to air supply.
- Heavy duty 12" flexible hose allows easy access to spark plug hole and air supply.
- Air pressure helps prevent the valve from falling into the combustion chamber.
Check Stock 
