Reviews Microcontroller Servo Board

STLINK-V3SET Microcontrollers ST STM8 and STM32 MCU USB Swim JTAG SWD Modular Stand-Alone in-Circuit Debugger Programmer SPI I2C CAN GPIOs @XYG

The STLINK-V3SET is a modular stand-alone debugging and programming probe for the STM8 and STM32 microcontrollers. It is composed of a main module and....
The SWIM and JTAG/SWD interfaces are used to communicate with any STM8 or STM32 microcontroller located on an application board..
The STLINK-V3SET also provides a Virtual COM port interface allowing the host PC to communicate with the target microcontroller through one UART, and....
The modular architecture of STLINK-V3SET enables to extend its main features through additional modules such as the adapter board..

Raspberry Pi Pico Evaluation Kit inlclude Raspberry Pi Pico with pre-soldered header ,1.14inch LCD Display Module,10-DOF IMU Sensor Module,Dual GPIO Expander ,830 Quality Breadboard etc.
Raspberry Pi Pico Board,a tiny, fast, and versatile microcontroller board,Built Using RP2040 Microcontroller Chip Designed By Raspberry Pi.
1.14" LCD Display Module for Pico ,Embedded ST7789 Driver, Using SPI Bus.
10-DOF IMU Sensor Module,an IMU sensor expansion module specialized for Raspberry Pi Pico. It incorporates sensors including gyroscope, accelerometer, magnetometer, baroceptor, and uses I2C bus for communication..
Dual GPIO Expander for Pico,Two Sets Of Standard Raspberry Pi Pico GPIO Male Headers.

The Central Board for your Electronic Project.
Powerful 32-bit Microcontroller and Micro SD Memory Card Connector.
Ideal for: Music, Audio processing, robotics, art installations.
Part of the Arduino Maker Board Family for IoT Devices, easy to configure with Arduino Software..

10CM Male to Male JR Plug Servo Extension Lead Wire Cable.
Great for jumping from board to board or just about anything else..
There is a 3-pin JST RE connector on both ends. These are simple jumper wires used on standard 0.1" breakaway headers..
Length:100mm Type:JR Plug Servo Extension wire (Male to Male).

It works with both digital and analog signals (the voltage can’t be higher than VCC), and the connections function in either direction.If you want two-way communications,you can add a second board to route your microcontroller's TX line to 16 device's RX lines. By using multiple boards, you can create similar arrangements for I2C,SPI,etc..
The internal switches are bidirectional, support voltages between ground and VCC, have low “on” resistance and low “off” leakage, and to prevent crosstalk, perform “break-before-make” switching. The board also breaks out the chip’s “enable” pin, which when driven high, will completely disconnect the common pin (all switches “off”)..
To control it, connect 4 digital outputs to the chip’s address select pins (S0-S3), and send it the binary address of the channel you want. This allows you to connect up to 16 sensors to your system using only 5 pins..
Since the mux/demux also works with digital signals, you can use it to pipe TTL level serial data to or from multiple devices. For example, you could use it to connect the TX pins of 16 devices to one RX pin on your microcontroller. You can t....

Embed version of Mega 2560 CH340G/ATmega2560 - compatible with Arduino Mega 2560 board..
Built on the Atmel ATmega2560 microcontroller and USB-UART interface chip CH340G..
Board have compact size 38x55mm. It is good solution, to make your final project on solder proto-board..
The board used the chip CH340G as converter UART-USB..

MEGA 2560 PRO Board Embed CH340G/ATMEGA2560-16AU Chip with Male pin headers, Compatible for arduino Mega2560 DIY.
Built on the Atmel ATmega2560 microcontroller and USB-UART interface chip CH340G..
Board have compact size 38x55mm. It is good solution, to make your final project on solder proto-board..
Board for functionality similar to the compatible for Arduino Mega 2560..
The board used the chip CH340G as converter UART-USB..

Raspberry Pi Pico is Raspberry Pi's first microcontroller board, designed especially for physical computing.
It can be easily reprogrammed over USB from a Raspberry Pi or other computer using the C/C++ SDK or the official MicroPython port.
Raspberry Pi Pico GPIO Expansion Board is used to break outall the pins and power of the Raspberry Pi Pico development board via male or female headers.
Raspberry Pi Pico GPIO Expansion Board allows the user to connect it to other components with the help of a jumper wire.
Raspberry Pi GPIO Expansion Board is specially made to work with the Raspberry Pi Pico Board.

The perfect IoT node and building block for adding to Lo-Ra connectivity to low power wide area IoT devices.
Very long battery life - the latest low power architecture means the power consumption is able to go as low as 104uA for extended battery life. It is also possible to use the USB port to supply power (5V) to the board, so you can run the board with or without batteries.
Local storage - On board 2MByte Flash to facilitate data logging and Over-The-Air (OTA) functions.
Enhanced Security - credentials and certificates are stored in the boards crypto chip, an embedded secure element.
Powerful - The MKR WAN1310 is based on the Atmel SAMD21 microcontroller and a Murata CMWX1ZZABZ Lo-Ra module.