Reviews Meter Base Antenna

Diamond Original SG7500A Dualband Mobile Antenna

The Diamond SG7500A is a 2 meter and 440 MHz (70 cm) mobile antenna. It is a 1/2 wave on 2 meters providing 3.5 dBi gain and a 2 x 5/8 wave on 440 providing 6.0 dB gain.
This antenna can handle up to 150 watts. VSWR: 1:1.5..
This antenna is approximately 41 inches (1.1 m) high. The antenna is black and silver. The connector type is UHF (for PO mount)..
This antenna does not include the mount or coax..
One of Diamond Antenna's Supergainer Premium mobile antennas..

The Winegard Boost XT Pro enhances any non-amplified antenna, delivering a clearer signal, more range, and more available channels. Only works with any passive/non-amplified antenna..
The integrated signal meter makes you the pro at installation. Pair with the Winegard Connected app for no-fuss antenna positioning..
TwinAmp Technology separately amplifies VHF and UHF signals for maximum performance and lowest noise and interference levels..
Winegard’s Clear Circuit Technology offers the lowest noise (1dB typical) to deliver more range and less signal dropout and pixelation..
Included components: Preamplifier, 110V adapter, hose clamp, USB power cable with 110V adapter, app-enabled Bluetooth technology signal meter, and printed documentation.

[High Frequency] The HYS antenna features VHF of 144/430 MHz (136-174MHz and 400-470Mhz) with VSWR:< 1.5, Gain: VHF 2.15/ UHF 3.15 dBi for better TX and RX..
[Efficient Performance] The antenna exhibits a maximum input power of 150W that works for all 2 meter 70 centimeters mobile radios..
[Durable] The mount is a “trunk lid” mount with 13 ft low-loss RG58U coaxial cable with UHF-male(PL259) connector installed. This is a high quality, low profile base mount that does the job very well..
[Easy Installation] The HYS antenna is equipped with 13 ft NMO cable that is connected easily with the antenna and still have plenty cable left to reach the antenna mount practically anywhere on your car or another other vehicle. For a rugged installation, all you require is a small, typically 3/8 inch 3/4 inch, hole to be drilled through the surface that will host the mount..
[Package Contents] The HYS package includes L-bracket hole stainless steel for trunk groove or side mounting, 3/4″ NMO hole mount with screws and L-bracket HYS TCJ-N1 coax NMO mount cable, mobile antennas perfect for car and truck’s hood..

Can Be Used In On Roof, Attic or Indoor/Outdoor! Approx 4ft Tall!.
VHF/UHF Dual Band Gain Base Antenna Great for 2 Meter & 70cm Amateur Bands!.
Handles Up to 300 Watts, Pretuned, 3.5/6.0 dB Gain!.
Includes U-Clamps for Mounting To An Optional Mast Pipe! Genuine ANLI Brand Item!.
Accepts Any Optional Lengths of Coax Cable w/PL-259 Connector..

Full 1.8-30MHz Operation Custom designed inductor switch, 1000 volt tuning capacitors, Teflon insulation washers and proper L/C ratio gives you arc-free no worries operation with up to 300 Watts 1.8 to 30 MHz.
Tunes any Antenna Tunes out SWR on dipoles, verticals, inverted vees, random wires, beams, mobile whips, shortwave receiving antennas.... Nearly anything! Use coax, random wire or balanced lines. Has heavy duty 4:1 balun.
Custom Inductor Switch The inductor switch is the most likely component to burn up in any antenna tuner. MFJs inductor switch in the MFJ-949E was custom designed to withstand the extremely high RF voltages and currents that are developed in your tuner..
8 Position Super Antenna Switch Lets you select two coax fed antennas, random wire/balanced line or built-in dummy load through your MFJ-949E or direct to your transceiver..
More hams use MFJ-949s than any other antenna tuner in the world! Has MFJs full size 3 inch lighted Cross Needle Meter (not a puny "meter" you cant read). Lets you easily read SWR, true peak forward and average reflected power simultaneously on 300 Watt or 30 Watt ranges. Lamp has on/off switch, requires 12 VDC or 110 VAC with MFJ-1312D (Not included).

Includes: TV Signal Strength Meter with Adapter Kit, and a Coaxial Cable.
Perfect For: Provides you with an over the air signal strength meter for digital TV antenna - designed for terrestrial digital television broadcast.
Features: The signal finder meter flaunts an impressive LED feedback display, sensitivity adjuster and coaxial Cable for an easy installation.
VERSATILITY - Perfect for positioning stationary mounted antennas or can be used by travelers in RV's looking to aim your directional antenna towards better signals in new or unfamiliar areas.
Quality Assurance: DTV signal finder Includes a US manufacturers warranty.

The MFJ-941E gives you a 300 Watt antenna tuner that covers everything from 1.8 - 30 MHz -- plus you get a lighted Cross-Needle meter with on/off switch, antenna switch and a 4:1 balun! (The light uses 12 VDC or 110 VAC with MFJ-1312D * Not included).
MFJs lighted Cross-Needle meter shows SWR, forward and reflected power all at a glance in 300/60 and 30/6 watt ranges, 8 position antenna switch lets you select 2 coax lines, random wire/balanced line or dummy load (direct or through)..
An efficient 12 position airwound inductor gives lower losses and more power out. Has 4:1 balun, 1000 Volt capacitors. The beautiful aluminum cabinet has a durable scratch-proof multicolor Lexan front panel matches your rig perfectly and fits right into your station..