Reviews Intake And Exhaust Manifold Protection

WPHMOTO Lifan 140cc 4-Stroke Racing Engine Motor and Muffler Exhaust With Pipe for XR50 CRF50 XR CRF 50 70 ATC70 Dirt Pit Bike Motorcycle

High performance Lifan 140cc engine, N-1-2-3-4 Gear, manual clutch, 4 stroke 4 speed, Shaft size: 17mm.
Max. Power & Corresponding Speed: 8kw(7500±375) / Max. Torque & Corresponding Speed: 9.5N.M(5000±250).
Replacement / upgrade for XR50 CRF50, Kawasaki KX KLX and other most popular dirt bikes.
Easy to hook everything up: Just remove your existing engine and reverse the process to put the new one in.
Package include: (1)Lifan 140cc Engine (1)Kick Starter Lever (1)Gear Shift Lever (1)Intake Manifold (1)Manifold hardware kit (1)Carburetor (1)Air Filter (1)CDI (1)Ignition coil (1)Wire Harness (1)Exhaust Muffler Pipe(1)Clutch Cable.

Replace Your Leaking or Worn out Intake Manifold Gaskets with These new OE Spec Intake Manifold Gaskets.
Manufactured with High Quality Silicon to Ensure an Air Tight Seal.
Molded to Factory Dimensions for a Perfect fit.
Compatible with 2008 and up LS3 Rectangle Port Intake Manifolds.

GY6 50cc Carburetor with 2-pin Male Electric Choke 18mm Intake Manifold.
GY6 50CC Carburetor comes with a #75 Main Jet. upgraded jets for better starting, idling and performance..
Size:Intake Manifold Side:18mm(Inner Diameter),28mm(Outer Diameter).
Air Filter Intake:35mm(inner diameter),39mm(Outer Diameter) ..
This is a 18mm Intake Carburetor,it fits most 4 stroke GY 49CC 50cc 80c 139QMA 139QMB Engine scooters carb, such as Taotao Baja, JMstar, Jonway,....
Package include: 1x Carburetor,1x Air Filter,1x Fuel Filter，1x Plug Spark,1x Intake Manifold，2 xGaskets..

1-1/8 inch width x 1-1/2" height Stock Square Port.
Ford V8 - 302 ('81-'95), 351 ('69-'97) Windsor, 1-1/8" x 1-1/2" Square Port, Manifold or Headers, 2/Set.
Heating and cooling of the exhaust system causes header and manifold flanges to warp resulting in gaps between the head and header which Remflex exhaust gaskets seal completely due to the thickness and compressibility of the 100 percent flexible graphite.
Remflex exhaust gaskets come in a standard 1/8 inch thickness and are designed to crush 50 percent allowing them to fill any pits or gaps in the flange surface up to 1/16 inch.
The aluminum cylinder head and steel header or manifold combination are configurations that readily cause gap issues in the mating flanges due to contraction and expansion of the dissimilar materials.
Remflex exhaust gaskets fill those gaps permanently.
There are no rubber binders or composite materials in Remflex exhaust gaskets so they will not shrink or harden due to time or temperature eliminating the need to go back and continually retighten your flange bolts.

【Deep removal of carbon deposits】Deeply remove the highly sticky carbon deposits on the intake manifold, intake & exhaust valves.（Solve the problems of unstable idling, insufficient fuel combustion, and reduced air-fuel ratio.).
【External air source】This enables the walnut sand grit to strike the carbon deposits more powerfully and efficiently..
【Built-in dust filter】It can separate the recovered walnut sand grit from carbon deposits for recycling..
【Integrated design】The walnut sand grit can be sprayed and recovered simultaneously..
【3 year warranty】For damage caused by non-human factors, we promise to resend parts for free within 3 years..

...ylinder Body & Reed Assembly is paired with a 21mm OKO Race carburetor is racer’s dream setup- get ready for a bike that’ll scream whenever you hit the gas!.
INCLUDES: Modified BBR Tuning Racing Series DIO Cylinder Body BBR Tuning Racing Series 6 Flap Reed Assembly BBR Tuning 21mm OKO High Performance Carburetor Manifold 1x Racing Air Filter 1x Angled throttle cable retainer 1x Slow Jet 1x Main Jet 1x Length of throttle cable.

【Deep removal of carbon deposits】Deeply remove the highly sticky carbon deposits on the intake manifold, intake & exhaust valves.（Solve the problems of unstable idling, insufficient fuel combustion, and reduced air-fuel ratio.).
【External air source】This enables the walnut sand grit to strike the carbon deposits more powerfully and efficiently..
【Built-in dust filter】It can separate the recovered walnut sand grit from carbon deposits for recycling..
【Integrated design】The walnut sand grit can be sprayed and recovered simultaneously..
【3 year warranty】For damage caused by non-human factors, we promise to resend parts for free within 3 years..

【Fitment】Dokili aluminum intake manifold for Small Block 1957-86 SBC Ch.e.v.y..
【Feature】Dokili intake manifold comes with dual-plane designs, providing power over a wide RPM range, from 1,500 to 6,500 RPM. The size of the port holes: 1.23" x 1.99". Bolt Hole Pattern: 5.160" x 5.625"..
【Dual plane】Dual plane designs have two smaller plenums that receive air from the carburetor or throttle body, which results in a higher velocity through the booster making the engine more responsive to the driver..
【Premium Material】Built with natural finish aluminum of superb quality and fit. Angles and straightness comparable to factory manifolds..
【Note】This intake manifold Will not fit under Corvette hood. Professional installation in highly recommended..

➤ 【PREMIUM QUALITY BUT LOWER PRICE】 Our intake manifold is designed for high durability and resistance by our strict process standards. We offer original manufacturer quality at lower cost than getting replacement at dealer..
➤ 【IDEAL REPLACEMENT】 This intake manifold directly replaces the original. Perfect fit, easy installation, high reliability.(NOTE❗)This kind of intake manifold with baffle，can't fit for others without baffle. Please kindly check the 5th image as show on..
➤ 【MANUFACTURER PART NUMBERS】4884495AK 4884495AD, 4884495AE, 4884495AF, 4884495AG, 4884495AH, 4884495AI, 4884495AJ, 4884542AC.
➤ 【FITMENT】Compatible with 2007-2010 Jeep Patriot,Jeep Compass 2.0L 2.4L / 2011-2017 Jeep Patriot,Jeep Compass 2.4L / 2007-2009 Dodge Caliber 1.8L 2.0L 2.4L / 2010 Dodge Caliber 2.0L 2.4L / 2011 Dodge Caliber 2.4L / 2008-2009 Dodge Avenger 2.4L / 2009-2011 Dodge Journey 2.4L / 2007 -2009 Chrysler Sebring 2.4l.
After installing the Flow Control Valve valve, please wave the manifold baffle by hand to ensure that it can rotate smoothly, and then install the manifold on the car.