Reviews Input output Isolation

Ernie Ball Volt Pedal Power Supply P06191

Photocoupler isolation between input control signal and controlled power, isolation surge voltage up to 7500V..
Input signal turn-on voltage DC 3 to 32V, turn-off voltage DC 0 to 0.8V. LED indication for relay turn-on..
Output voltage range: AC 90 to 250V(50/60Hz). Maximum on-state average current 3 Amp. Maximum on-state current 10 Amp (003c 10 seconds). Non repetitive surge peak on-state current: 120 Amp (003c20mS). Load type: General purpose..
This is a simple and practical solid state relay module, which is very convenient to use, for Arduino, Raspberry Pi, ESP32, PLC or other projects. The GPIO of these controllers are directly connected to this relay input to control the mains power, and it is suitable for most loads less than 350 Watts (for 115VAC)/700 Watts (for 230VAC)..
Compact ABS plastic case and wires connect for easy mount. Two screw mounting holes are convenient for you to fix it on the wall or wooden board. Of course, you can also choose not to lock the screw..

The attenuation rate is 10X, which can be used in any brand of oscilloscope, meet the needs of floating measurement..
DP series high‑voltage differential probes, specially designed for the measurement of high‑voltage differential signals..
High‑voltage differential probes sample high‑impedance isolation between input and output to protect person safety..
The power supply adopts USB DC 5V output and has a USB interface, which is easy to use and carry..
Convert the input high voltage signal to low voltage signal for oscilloscope observation and analysis..

➤【DC12-32V】- This isolation module need two complete independent DC12-32V power supply..
➤【Main function】- Main function is input 0-10V analog voltage signal,after isolation, output 0-10V analog voltage signal..
➤【Scope of Application】- Used to isolate high voltage or strong interference voltage or current (voltage) signal then transferred to PLC or controller MCU, isolating controlling end and controlled end, to assure stability and anti-interference ability of system..
➤【Use】- It will has better performance if install this module and controller in a metal box and box is grounded..
➤【Note】- The potentiometer is used to amend corresponding relation of output voltage. Output voltage can be fine adjusted and calibrated, normally it has already been calibrated..

1. Power Clean: Complete line isolation, Eliminate EMI/RFI line noise and provide clean power for sensitive equipment.
2. Isolation Transformer: Toroidal transformer and Faraday Shield, reduce the static interference from the wall outlet.
3. Power supply: 120V AC input and 120V AC output.
4. 2 outlets: allow to use 2 equipment at same time and a power strip for more.

Has good low temperature resistance, superior insulation, moisture, leakage, shock, corrosion, anti-aging and other properties..
Conformal coating is used to protect circuit boards and related equipment from environmental erosion..
Photoelectric isolation against high frequency interference, suitable for a wider environment, protect equipment, and not affect the temperature of the working environment..
High-quality ABS material shell, high temperature and impact resistance, can be used for a long time.
Realize the isolation of input, output, power supply and shell, strong anti-interference ability and high reliability..

Safe Security: Mutual inductance current monitoring has high current detection accuracy and safe isolation of input and output..
Easy To Use: Easy to install and use, no need to connect DC into the circuit when measuring..
Product Specification: Self-powered, no external power supply required. Measured current AC 0-10/20/50A, output signal DC 0-5V. Straight-through structure design, isolation withstand voltage up to 2000V..
High Quality：The outer casing is made of self-extinguishing material ABS..
Widely Application: Hysteresis is less than 1% and can be used under strong magnetic conditions. Suitable for AC current measurement and monitoring, AC motor overload protection, electronic switch of automatic control system and so on..

1 road video signal input, 8 roads video signals output simultaneously, BNC interface..
With premium component and advance circuit design, Support resolution up to 1080p 60Hz input..
Plug and Play, High isolation, no distorition for output signal and no interference..
Suitable for public video system, simple TV teaching, multi-screens monitoring system and so on..
What you have: 8-port BNC splitter, US power adapter, User manual, One year warranty from AuviPal..

1/2-Din Chassis Graphic Equalizer with Built-In Low-Pass Filter6-Channel / 8-Volt RCA Outputs.
3.5mm Front AUX Input2-Channel RCA AUX Input with Variable Gain AdjustmentRCA and High Level.
Blue IlluminationIndependent Master Volume and Subwoofer Level Control with Fader.
Ground Loop Isolation CircuitDimensions: 7(W)x4-1/4(L)x1(H).