Reviews Ict Billet Ls

Z Whip LS Oil Pump Pickup Tube Girdle Pipe Hold Down Brace Support Billet Bracket MADE IN THE USA Compatible with GM Chevy LS Series Engines LSX LS1 LS3 LS2 LQ4 LS6 LQ9 5.3L 6.0L 6.2L

  • Compatible with all LS Series Engines 1997-2014 (GEN. III/IV small block chevy).
  • The factory oil pickup tube on LS engines is only secured by one bolt. This can potentially lead to a poor seal on the oil pump. Our Billet aluminum Oil pump girdle solves the issue by placing a clamp on both sides of the tube, securely holding it in place..
  • DOES NOT fit any LS oil pickup tube with welded flanges (GM # 12608593, Holley 302-1 and similar tubes). DOES NOT fit pickup tubes with two screw holes on their flange (Holley 302-2 tube and similar tubes)..
  • Proudly made in the USA from Aerospace Grade Billet Aluminum.
  • We are an AS9100D and ISO 9001:2015 Certified Manufacturer. Parts we produce fly at 30,000 feet where failure is not an option..
Check Stock

ICT Billet LSA LS9 LT4 Supercharger MAP Vacuum Port Cap Plug Plate LS SC Blower ICT 551383

  • Compatible with LSA, LS9, and LT4 superchargers.
  • Can be used to plug 1 or both MAP sensor port locations.
  • Billet plug securely seals MAP sensor bores.
  • Includes: 1 plug, with FKM oring, and USA made bolt.
  • Made in Wichita, Kansas from aerospace grade, USA produced, billet aluminum.
Check Stock

LKONWEE Billet Aluminum Oil Diverter Barbell Oil Restrictor Galley Plug Fits GM Gen III & IV LS Engines LS1 LS2 LS3 LS6 LS7 LS9 LQ4 LQ9 4.8L 5.3L 6.0L 6.2L

  • Compatible with all GM LS Series Engines inclued LS1 LS2 LS3 LS6 LS7 LS9 LQ4 LQ9 4.8L 5.3L 6.0L 6.2L LM7 LR4 L59 LM4 L33 LH6 L92 L76 LY2 LY5 LY6 LC9 LFA LH8 LMG L98 L9H L20 L94 LZ1 L99 L96 LC8 L77.
  • Compatible with GM Gen III & IV Engines..
  • Directly to replace the factory plastic barbell，machining have less tolerance, makes the gap smaller,makes the gap smaller, so that it can prevent dust from entering oil and keep it clean..
  • It was designed with a little taper, which will makes oil flow smoothly,can effectively prevent the loss of engine oil, increasing the use of flow..
  • Made of quality billet aluminum material. 1/4-20 threaded hole aids in easy removal..
  • When using the barbell, please wipe the using part cleanly and Lube the Oring. Then insert the barbell and screw it in with firm pressure..
Check Stock

4AN Turbo Oil Feed Restrictor Fitting For GT25 GT25R GT28 GT28R GT35 GT35R T25 Turbocharger Ball Bearing Turbo Oil Feed 1MM M12 x1.25 Thread

  • Fits GM Gen III & IV LS Engines LS1-2-3-6-7-9-LQ4-LQ9-4.8L-5.3L-6.0L-6.2L & More! SAME BUSINESS DAY SHIPPING!.
  • BEWARE OF COPYCAT COMPANIES! COMPARE THEIR INFERIOR MACHINE WORK AND CHEAP MATERIAL TO OURS! SCCITYCORVETTE IS THE ORIGINAL INVENTOR OF THE PRECISION LS BILLET BARBELL, BYPASS DELETe & GALLERY PLUG! TO KEEP UNFILTERED OIL FROM GETTING INTO THE BEARINGS AND LIFTERS, WE KEEP EXACT TOLERANCES THAT COST MORE TO MANUFACTURE. NOT HOLDING EXACT TOLERANCES DEFEATS THE PURPOSE OF KEEPING UNFILTERED OIL OUT. COPYCAT COMPANIES DO NOT HOLD OUR TOLERANCES, THAT’S WHY THEY ARE SO CHEAP!.
  • The factory plastic barbell is approximately .020” to loose so particles as big as 500 Microns can leak passed the factory Barbell. When oil leaks pass the Barbell it goes unfiltered directly to the Cam Bearing, Lifters, Crank and Rod Bearings. Your oil filter will filter out approximately 25 Microns depending on the brand of filter. Our Aluminum Precision Billet Barbell fits with approximately .001” clearance which will let only about 20-25 Microns pass by, that is the same as the filter..
  • Our New Tapered Design and 30% smaller shaft greatly increaseoil flow!.
  • We have also added a 1/4-20 threaded hole in the end of our Barbell for easy removal. Just screw a 1/4-20....
Check Stock

Lawn Tractor Steering Arm Drag Link Fits AYP Craftsman Husqvarna 532169832 169832

  • 45-142 Steering Draglink Compatible With Craftsman 169832, 532169832 Drag Link.
  • This drag link (part number 532169832) is for lawn tractors.
  • Includes (1) Link Drag. Replacement Husqvarna Part. New, Bulk Packed. Consult owners manual for proper part number identification and proper installation. Please refer to list for compatibility..
  • Fits: Husqvarna Models: CT 130 CTH 130 CTH 150 GTVH 205 LT 1238A LTH 120.
  • Fits: Jonsered Models: ICT13 ICT13A ICT15 ICT16A ICT18A LT12 LT13 LT13A.
Check Stock

My Proparts Hub MAP Sensor Adapter Harness Wire LS1 LS2 LS7 to LS3 LS9 ZR1 L92 LSA Style

  • Assembled with OEM tooling, OEM (connector, lock, seals, and terminals),(uses OEM harness wire colors) for a perfect fit.
  • Assembled in Wichita, Kansas with USA made OEM grade TXL wire.
  • Extend The Length Of Your Factory Harness With ICT Billet Wire Extension Harnesses.
  • Highest Quality Wire Connectors On The Market, For the Most Dependable, Longest Lasting Connections.
Check Stock

ICT Billet LS Throttle Body Adapter - LS1 3 Bolt Intake Manifold to LS3 4 Bolt Throttle Body DBC LM7 LR4 LQ4 LS6 L59 LQ9 LM4 L33 LSX 4.8L 5.3L 5.7L 6.0L Billet 551513

  • This throttle body adapter will allow you to install a 4 bolt LS throttle body onto a 3 bolt LS intake. For example, a 92mm billet throttle body.
  • Adapter Has 75mm Through Hole, Tapered To 92mm For The Throttle Body..
  • Compatible With Both DBW And DBC 4 Bolt Throttle Bodies..
  • Made in Wichita, KS from aerospace grade, USA billet aluminum..
  • Throttle Body Adapter Will Come With A Adapter Plate, All Bolts, And An Oring Seal Needed For Installation..
Check Stock

ICT Billet 5.3L 6.0L Turbo LS Truck Alternator Relocation Bracket Kit Compatible with Truck / LS3 L99 Camaro SS Water Pump 4.8L 5.3L 6.0L 6.2L LSX LM7 LR4 LQ4 L59 LQ9 LM4 L33 551587-LS01-3

  • Compatible with all GM LS series engines.
  • Made in Wichita Kansas from aerospace grade USA billet aluminum.
  • Compatible with truck/SUV (or LS3/L99 Camaro) crank pulley.
  • Compatible with 1998-2002 LS1 Camaro (or LS3) water pump.
  • Includes alternator bracket and mounting hardware.
Check Stock

ICT Billet LS Twin Turbo Dual 1/8' NPT Oil Feed Line Adapter Plate LS1 LSX kit Port LS3 Billet Plate Supply Pressure Sensor Cover LS3 LS2 LQ4 LQ9 LS6 L92 L99 L33 LR4 551666

  • Oil Supply Plate Provides X2 1/8"NPT Oil Supply Ports For Single or Twin Turbocharger Feed Lines.
  • 1/2" Thick Heavy Duty Aluminum Allows More Oil To Flow Through The Engine Internally.
  • Made in Wichita, Kansas from aerospace grade, USA produced billet aluminum.
  • Compatible with all LS oil pans except front sump and/or dry sump oil pans (LS7, LS9, LS4, GTO).
  • Includes 1 plate with oring and mounting bolts.
Check Stock