GY-521 MPU-6050 MPU6050 Module, 3 Axis Accelerometer 6 DOF Gyroscope Sensor Module Kit 16 Bit Converter Data Output IIC 3-5v Compatible with Arduino (10 Pieces)
- GY-521 MPU-6050 module: integrates 3-axis gyroscope and 3-axis accelerator, including the hardware accelerator engine for devices connected to the second I2C port, like another accelerator of other brands, magnetometer, or Digital Motion Processor (DMP) of other sensors.
- Parameter range: the MPU-6050's angular velocity range is ±250, ±500, ±1000 and ±2000°/sec (dps) for accurate fast and slow motion, and user-programmable accelerator full-frame sensing the range is ±2g, ±4g±8g and ±16g.
- Transmission can pass I2C up to 400kHz or SPI up to 20MHz.
- Chip built-in: with three 16-bit analog-to-digital converters (ADCs) for digitizing the gyroscope outputs and another three ones for digitizing the accelerometer outputs.
- Easy to use: the measured values of the sensor can be interrogated by the I2C interface.
- The accelerometer can be operated at both 3.3V and 5V.
- Compatible with Arduino and Raspberry Pi.
- Universal usable: the sensor can be applied to develop various entertaining applications and systems.
- Nice for projects with gaming and virtual reality devices, navigation (for drones and RC planes) and DIY robots.
Check StockSEEU. AGAIN 4pcs 0.96 Inch I2C OLED Display Module IIC SSD1306 128x64 LCD White with 4 Pin Female to Female Du-pont Wire
- I2C mode up to 400Khz, configurable slave address.
- Two pin 3.3V UART mode, baud rates {9600, 19200, 38400, 57600, 115200}.
- 4-pin SPI mode, supports all 4 standard SPI modes, up to 3Mhz clock.
- Backlight brightness and contrast controlled by software commands.
- Source code examples for custom applications, showing how to interface with the LCD from any I2C/UART/SPI hardware.
Check StockMakerFocus Lidar Range Finder Sensor Module TF-Luna, Single-Point Micro Ranging Module 0.2 to 8m Compatible with Pixhawk, Arduino and Rasppbarry Pi with UART / I2C Communication Interface
- English product manual: Get the link in the product guide and document. Note: TF-Luna module comes with UART and I2C interface, the default is UART, if you need to use I2C interface, please set it yourself..
- TF-Luna: TF-Luna is a single-point ranging LiDAR, based on TOF principle. With unique optical and electrical design, it can achieve stable, accurate and highly sensitive range measurement..
- Product Characteristics: The product is built with algorithms adapted to various application environments and adopts multiple adjustable configurations and parameters so as to offer excellent distance measurement performances in complex application fields and scenarios..
- Extreme Cost Performance: Low-cost ranging LiDAR module, with 0.2-8m operating range. TF-Luna has a highly stable, accurate, sensitive range detection..
- Slim Figure Yet Big Skill: The product is built with algorithms adapted to various application environments and adopts multiple adjustable configurations and parameters so as to offer excellent distance measurement performances in complex application fields and scenarios..
Check StockSonghe 5MM LDR Photosensitive Sensor Module Light Dependent Resistor Sensor Module Digital Light Detection LM393 3 pins for Arduino (10PCS)
- The BH1750FVI sensor to measure the ambient light level. BH1750FVI is a calibrated digital light sensor IC that measures the intensity of incident light and converts it to a 16-bit digital number..
- It can measure the ambient light intensity ranging from 0 to 65535 lux (L). Lux is an SI unit for illuminance and is equal to one lumen per square meter. The BH1750FVI sensor directly gives the output in Lux..
- The sensor's spectral response function is approximately similar to that of the human eye. The sensor output can be accessed via an I2C interface. The 7-bit I2C address is 0 × 23 if the ADDR pin is grounded, or if the 0x5C ADDR is bound to VCC..
Check StockArducam Mini Module Camera Shield with OV2640 2 Megapixels Lens Compatible with Arduino UNO Mega2560 Board and Raspberry Pi Pico
- Compatible with Arduino, Raspberry Pi Pico, MCU, Raspberry Pi, ARM, DSP, FPGA platforms.
- 2 megapixels image sensor OV2640, build-in 650nm IR block filter, visible light only.
- M12 mount or CS mount lens holder with changeable lens options.
- I2C interface for the sensor configuration,SPI interface for camera commands and data stream.
Check StockACEIRMC 2pcs ESP32-CAM WiFi Bluetooth Camera Module Development Board ESP32 with Camera Module OV2640 2MP for Arduino (4pcs)
- The ESP32CAM is a tiny module based on ESP32 chip and OV2640. You can even program the ESP32CAM through the ESP-IDF by installing the ESP32 Core.
- ESP32-CAM WiFi Bluetooth Module WiFi ESP32 CAM Development Board with Camera Module OV2640 2MP for Arduino, Support Image WiFi Upload and TF Card.
- Supports interfaces such as UART/SPI/I2C/PWM/ADC/DAC.
- Support OV2640 and OV7670 cameras, built-in flash.
- Support image WiFi upload and Support TF card.
- Bluetooth: Bluetooth 4.2 BR/EDR and BLE standard.
- Ultra-small 802.11b/g/n Wi-Fi + BT/BLE SoC module.
Check StockArducam Mini Module Camera Shield 5MP Plus OV5642 Camera Module, Compatible with Arduino UNO Mega2560 Board
- Arducam Mini Module Camera Shield 5MP Plus OV5642 Camera Module is a general purpose high definition 5MP SPI camera, which reduce the complexity of the camera control interface.
- It integrates 5MP CMOS image sensor OV5642, and provides miniature size, as well as the easy to use hardware interface and open source code library.
- The Arducam Mini is compatible with Arduino, Raspberry Pi, Raspberry Pi Pico,ESP8266, Maple, Chipkit, Beaglebone black, as long as they have SPI and I2C interface.
- Support JPEG compression mode, single and multiple shoot mode, short movie recording, one time capture multiple read operation, burst read operation, low power mode and etc..
- It can be used in IoT, Robot, Wildlife, HDR and Other battery-powered products or scientific image processing applications.
Check Stockseeed studio Ethernet Shield
- High-speed Ethernet controller W5200 with integrated Ethernet MAC & PHY.
- Supply voltage: min: 4.75VDC, typical: 5VDC.
- microSD card socket supports SD card in FAT16 or FA.
Check Stock