Reviews High Voltage Module

DC DC Buck Boost Converter Variable Voltage Regulator CC CV 0.5-30V 4A 5V 6V 12V 24V Power Module Adjustable Voltage Regulated Laboratory Power Supply

  • output voltage range is DC 0.5-30V, can be arbitrary adjustable.
  • output current can be 3A for long term use, if enhance heat dissipation, it can reach 4A.
  • max output power is 35W, if enhance dissipation, it can reach 50W.
  • LCD displays input/output voltage, output current/output power/output capacity/output time.The module can be set to ON/OFF by default.
  • Safe Protection: the module is with Anti-reverse connection protection of input end, so that it will not burn out when there is reverse connection.Anti-backflow protection at the output end. No need to add anti-backflow diode when charging. Multiple software protection mechanisms are available, and the protection threshold is adjustable. When the working parameters of the module exceed the protection threshold, the output will be automatically turned off.
  • Application: the volt conversion board can be used as an ordinary buck/Boost module with over-current protection.
  • used as a high-power LED constant current driver module.
  • DIY a solar power controller, Battery Charging.
  • Output ripple is small and πfilter is available.Thick heat sink .Buck-boost Integrated.
Check Stock

UMLIFE 3pcs ACS712 Hall Effect Current Sensor Module 30A Range ACS712 Module + 3pcs Voltage Sensor Module DC0-25V Voltage Tester Terminal Sensor for Arduino Raspberry Pi

  • ❃❃ Package Included：3 x ACS712 Hall Effect Current Sensor Module + 3x Voltage Sensor Module DC0-25V Voltage Tester Terminal Sensor.
  • ❃❃A wide range of applications:The current sensor ACS712 provides economical and accurate solutions for ac or dc sensing in industrial, commercial and communication systems. Typical applications include motor control, load detection and management, switching power supply and overcurrent fault protection..
  • ❃❃ACS712 Hall Effect Current Sensor Module：Chip: ACS712ELC-30A.
  • Pin 5V power supply, on-board power indicator.
  • ❃❃Voltage Sensor Module：Voltage input range: DC0-25V.
  • input : Terminal cathode connected to VCC, GND negative pole.
  • Output interface: "+" then 5/3.3V, "-" then GND, "s" then the for AD pins..
  • ❃❃Perfect Combination：Using this product can measure both voltage and current, very suitable for DIY electronic design projects..
Check Stock

Bridge Rectifier, 3Pcs AC to DC Power Conversion Module, 1N4007 Full Bridge Rectifier Filter Power Supply Module for Model Train Railroad LED (Input AC 6V-16V (capacitance 25V1000UF))

  • AC to DC power converter module, 1N4007 full wave bridge rectifier filter. Module size: 31x14x20mm/1.22x0.55x0.78inch, wire Length: 90mm/3.54inch..
  • This product is a streamlined rectifier filter module, widely used in small rectifier output filter, mainly used in the power requirements of the electrical is not very high..
  • The power module design can be put into a smaller small electrical box, the circuit Board above the design of power indicator light, easy to turn on the power supply can be intuitive to know the power status..
  • Rectified output voltage: output = input x1.414 . Example: input 12V AC, then the output 12x1.414 = 16.968V, which is the calculated result of no-load voltage, only a reference, the actual deviation..
  • Please NOTE: plug-in products, manual soldering, inconsistent capacitor pin height is a normal phenomenon. AC input voltage [6V-16V] (capacitance 25V1000UF).
  • AC input voltage [6V-32V] (capacitance 50V470UF), please seclect the one you need..
Check Stock

PC Interface Controller

  • 【One-year after-sale warranty】The PWM to voltage module converts PWM digital signals to 0 to 10V analog signals. It can be used to switch the signal interface of PLC or other industrial control board. Adjust the output voltage by adjusting the PWM duty cycle. The module is small in size and easy to apply in different places.003cbr003e.
  • Using MCU embedded technology. Easy to operate, can be fine-tuned by potentiometer.003cbr003e.
  • Select the PWM signal input level range by short circuit. The module is small, easy to carry and easy to use.003cbr003e.
  • (current greater than 100mA)，PWM signal receiving frequency range: 1KHZ-3KHZ.
  • When power on for the first time, it is best to do a calibration and debugging: find a signal with a 50% duty cycle and connect it to PWM and GND. Jumper caps set the corresponding voltage range. When the frequency is 1KHZ-3KHZ, use a multimeter to measure the two ports of VOUT and GND. At this time, the meter displays about 5V. Adjust the potentiometer on the board so that the multimeter displays 5.00v.003cbr003e.
Check Stock

4Pcs INA219 I2C Bi-Directional DC Current Power Supply Sensor Breakout Board Module I2C IIC Interface

  • INA219 module is an I2C interface with a drift, bi-directional current / power monitor integrated circuit (IC), and further expand the energy-saving....
  • INA219 I2C Bi-directional DC Current Power Supply Sensor, Working Voltage 3~5V.
  • INA219 module small size, low cost, high accuracy. It not only can monitor the voltage drop across a shunt resistor on the sensing shunt supply....
  • INA219 can be achieved within the maximum error accuracy of +1% from -40° C to 85° C temperature range, the maximum offset is 100 uV. The....
  • Appliaction:The module is used for I2C port zero drift / bidirectional current / power monitoring sensor module. The device is available in a SOT23....
Check Stock

10 Pieces DC-DC Boost Converter 2A Adjustable Module Voltage Regulator Board Input Voltage 2 Volt-24 Volt to 5 Volt-28 Volt Output Voltage (Without USB Connector)

  • Product size: 36 x 17 x 14 mm/ 1.42 x 0.67 x 0.55 inch (L x W x H).
  • Method of use: the module of the IN+ and - after 2-24V, IN adjusting the potentiometer can adjust output voltage, output voltage is greater than the input voltage.
  • Matters needing attention: 1. The input voltage should not exceed the maximum input voltage.
  • 2. The peak current output current is no more than TV university.
  • Package included: 10 x DC-DC power apply module booster power module, max output is 28Volt.
Check Stock

AC 50-220V 2000W 25A Motor Speed Controller SCR High-power Electronic Voltage Regulator Module Motor LED Dimmerswith Speed Control Knob(5pcs)

  • Material: made of electronic components, internal conductor: pure copper..
  • Features: The module uses thyristors, with a withstand voltage of up to 1200V. The regulator has a peak voltage absorption circuit, which can effectively protect high-power thyristors, has a long service life and is more durable. High-quality CBB capacitors can withstand 630V DC withstand voltage..
  • Note: The module is connected to an AC voltage of 220V, so safety must be paid attention to during the debugging process to prevent electric shock accidents..
  • Specification size: high temperature resistant FR-4 circuit board circuit board 35MM * 48MM, external size: 48MM * 60MM (knob direction) * 26MM (height).
  • Package contains: 5 * 50-220V 25A AC motor speed regulator.
Check Stock

0-10V Signal Isolation Module, S-10V10V Analog Quantities Voltage Signal Isolation Module for PLC/MCU Isolating High Voltage or Current (Voltage) Signals

  • ➤【DC12-32V】- This isolation module need two complete independent DC12-32V power supply..
  • ➤【Main function】- Main function is input 0-10V analog voltage signal,after isolation, output 0-10V analog voltage signal..
  • ➤【Scope of Application】- Used to isolate high voltage or strong interference voltage or current (voltage) signal then transferred to PLC or controller MCU, isolating controlling end and controlled end, to assure stability and anti-interference ability of system..
  • ➤【Use】- It will has better performance if install this module and controller in a metal box and box is grounded..
  • ➤【Note】- The potentiometer is used to amend corresponding relation of output voltage. Output voltage can be fine adjusted and calibrated, normally it has already been calibrated..
Check Stock

ATNSINC 4Pack LM2596 DC-DC Buck Converter, Adjustable Step Down Voltage Regulator 3-40V to 1.5-35V High Efficiency Power Supply Volt Reducer Transformer Module

  • The input voltage: DC 3 -40 V (Input voltage must be 1.5 V higher than the output voltage, no boost.).
  • The output voltage: DC 1.5 - 35 V adjustable..
  • The output current: It is recommended to use under 2A, maximum 3A(Additional heatsink is required)..
  • Steps: 1. Plugged into a power supply (3-40v), the power indicator light is lit, the module to work properly. 2. Adjust the blue potentiometer knob (generally booster clockwise, counterclockwise step-down) with a multimeter monitoring the output voltage to the voltage..
  • Package includes:4XLM2596 DC-DC buck converter module（Note：The factory have tested these at max voltage so they are very high by default, takes about 15-20 turns CCW before the voltage starts ramping down).
Check Stock