Reviews Heavy gauge Puller Tool

VCT Rear Axle Bearing Remover Puller Slide Hammer Set Remove Semi-Floating

  • EASY TO USE: Slide flat end of puller through center of bearing and flat against backside of bearing, then slide washer down the center of the shaft against front side of bearing and tighten the nut on smaller end of puller, then thread a slide hammer (not included) to the puller and slide hammer back and forth until the bearing comes out.
  • The washer captures the bearing firmly to distribute the applied force over the entire bearing and prevent damage.
  • Use the VCT Pneumatic SAE Standard Rear Axle Bearing Puller 3-Piece Service Set – Domestic Car Vehicle Bearings Removal Tool Kit to service semi-floating rear axle bearings on your vehicle.
  • These tools make the job simple and prevent damage to your bearings when pulling.
  • Much easier than claw-type axle bearing pullers that slip off and chew up the old bearings.
  • For removal only, not intended for installation.
  • FITS YOUR CAR: Standard SAE sizes work for most American domestic makes and models.
  • Set includes the following sizes to fit main bearing tube – 1 inch to 1-7/8 inches, 1-5/16 inches to 2-3/8 inches, and 1-3/8 inches to 2-7/8 inches.
  • Sizes permanently laser-etched on tool for easy identification.
  • Each tool fits a basic slide hammer with a 5/8-inch x 18 thread pitch.
Check Stock

VEVOR Hydraulic Gear Puller 15 Ton Max Capacity Hydraulic Puller 2 or 3 Jaws Bearing Hub Separator 3.9 - 11.8 Hydraulic Puller Separator Tool for Pulling Hubs Flanges Gears Bearings

  • Durable Material: The hydraulic gear puller is made of heavy-duty forged steel, featuring superior strength and no oil leakage. It's very sturdy and possesses 15T (33069 lbs) maximum capacity and a long service time..
  • Adjustable Jaws: You can install two or three jaws and adjust the height as needed. Besides, the pump head of the hydraulic bearing puller can rotate 360 degrees, which is easy for you to operate and use the tool..
  • Bidirectional Operation: The 15-ton hydraulic gear puller can be operated horizontally or vertically without site restriction. It has 2" (50 mm) axis travel with 7" (180 mm) max reach and 12" (300 mm) max spread..
  • Humanized Design: Equipped with a security relief valve, the piston rod, the detachable ejector pin, and the movable handle, the hydraulic steering wheel puller has the advantage of compact structure and working agility..
  • Diverse Scenario: A hydraulic puller set is an ideal tool for pulling hubs, flanges, gears, pulleys, flywheels, bearings chucks from shafts. It is widely suitable for car maintenance factories, mechanical factories, and repair workshops, etc..
Check Stock

OEMTOOLS 27031 Power Steering Pulley Puller and Installer Kit, Removes and Installs Power Steering Pump Pulleys on Most Domestic Vehicles, Ford, GM, VW

  • POWER STEERING PULLEY INSTALLER AND REMOVER: Our power steering pulley tool is designed to remove and install power steering pump pulleys on most domestic vehicles.
  • Power steering pulley remover pulls pressed-on water pump pulleys of GM V6 engines.
  • WORKS WITH MANY VEHICLES: This power steering pump pulley tool comes with two screws for use on most Ford, Chrysler, GM, and VW power steering pulleys with Saginaw, Thompson and Ford C111 and C2 pumps.
  • Pulls pulleys on GM belt-driven vacuum pumps.
  • HEAVY-DUTY POWER PULLER: The pulley clamp and removal screws in this OEM pulley puller installer kit are composed of rugged steel for long-lasting strength and durability.
  • Power steering pump pulley installer designed to tackle any small pulley job.
  • CONVENIENT STORAGE: Our power steering puller and installer set comes in a molded carrying case for safe storage and easy portability.
  • Take this power steering pump puller/installer from job to job while keeping your puller kit organized.
  • PRODUCT SPECIFICATIONS: Pulls any pulley with hub diameters measuring 1-1/8, 1-1/4, 1-5/16, or 1-3/8 inches.
  • Pulls pulleys on GM belt driven vacuum pumps.
  • Pulls pressed-on water pump pulleys of GM V6 engines.
Check Stock

EWK Camshaft Sprocket Pulley Puller Removal Tool Kit for VW Audi V6 V8 T40001

  • 【 Specialty Tool 】This puller is designed to pull off the camshaft sprocket. Can be lock on gear with 5 or 6 spokes. The length of puller arm are 17mm and 23mm Hex head 17mm pressure screw with rounded end for reducing damage to sprocket..
  • 【 Must Have 】Cam sprocket puller is the essential tool when replacing the timing belt on the Audi V-6 and V-8 engines. Dismantle camshaft sprockets safely with uniform pressure Replaces OEM part number T40001..
  • 【 Heavy Duty 】This puller kit bears high pressure and can deal with stubborn cams. Easily takes off tough cam sprockets that hard to loose without deforming, bending or spreading. Placed in a sturdy blow molded case makes storage and transportation more convenient and organized..
  • 【 Wide Applications 】 Widely suitable for Audi: 80, 100, A4, A6, S6, A8, S8, RS4, RS6.
  • Volkswagen: V6 2.4, 2.6, 2.7, 2.8 Petrol, V8 3.7, 4.2 Petrol.
  • Skoda: Superb. Please refer to the owner’s manual before using..
  • 【 EWK Assurance】Excellent WorKing experience guaranteed! EWK provides you premium quality tools and the best service with 12 month....
Check Stock

Orion Motor Tech 3\ 4\ 6\ 8\ 3-Jaw Gear Puller Set for Removal of Bearings Pulleys Flywheels

  • Universal Removal Tool: This 3-jaw removal tool set works with your wrench, ratchet, or spanner as a gear puller, sprocket puller, bearing puller, pulley puller, flywheel puller and more, removing even rusted parts easily and—thanks to its even distribution of force—without damage..
  • Better Together: This professional or home tool kit includes four puller sizes to cover most applications: a 3 inch gear puller with a 4.3" max. reach and 3" max. spread.
  • a 4 inch gear puller with a 5" max. reach and 4" max. spread.
  • a 6 inch gear puller with a 7.3" max. reach and 6" max. spread.
  • and an 8 inch gear puller with a 9.3" max. reach and 8" max. spread..
  • Versatile Design: Each of the three smaller 3-jaw gear and bearing pullers can be reversed to pull parts from the inside or outside.
  • the 8 in. puller can be used in 4 different positions to deal with both medium and large parts..
  • 45# Carbon Steel: All parts are made with premium heat-treated 45# carbon steel for maximum strength. The jaws are galvanized and the central screw coated with black oxide to provide superior corrosion resistance and long service life..
  • Satisfaction Guaranteed: Along with this gear and bearing removal tool kit's durable material and careful engineering, you can rest easy knowing that th....
Check Stock

OEMTOOLS 37031 Power Steering Pulley Puller and Installer Kit, Removes and Installs Power Steering Pump Pulleys on Most Domestic Vehicles, Ford, GM, VW , green

  • POWER STEERING PULLEY INSTALLER AND REMOVER: Our power steering pulley tool is designed to remove and install power steering pump pulleys on most domestic vehicles.
  • Power steering pulley remover pulls pressed-on water pump pulleys of GM V6 engines.
  • WORKS WITH MANY VEHICLES: This power steering pump pulley tool comes with two screws for use on most Ford, Chrysler, GM, and VW power steering pulleys with Saginaw, Thompson and Ford C111 and C2 pumps.
  • Pulls pulleys on GM belt-driven vacuum pumps.
  • HEAVY-DUTY POWER PULLER: The pulley clamp and removal screws in this OEM pulley puller installer kit are composed of rugged steel for long-lasting strength and durability.
  • Power steering pump pulley installer designed to tackle any small pulley job.
  • CONVENIENT STORAGE: Our power steering puller and installer set comes in a molded carrying case for safe storage and easy portability.
  • Take this power steering pump puller/installer from job to job while keeping your puller kit organized.
  • PRODUCT SPECIFICATIONS: Pulls any pulley with hub diameters measuring 1-1/8, 1-1/4, 1-5/16, or 1-3/8 inches.
  • Pulls pulleys on GM belt driven vacuum pumps.
  • Pulls pressed-on water pump pulleys of GM V6 engines.
Check Stock

ABN 13 Piece Harmonic Balancer Steering Wheel Puller Kit

  • [Car Maintenance Made Easy]: When removing harmonic balancers, gear pulleys, steering wheels, and crank shaft pulleys, depend on the ABN 13 Piece....
  • [Even Application]: No need to worry about steering wheel puller harmonic balancer puller kit causing damage to car parts.
  • [Built to Last]: Steering wheel puller kit bits are hardened and tempered to ensure longevity and strength.
  • Machine precision flywheel puller tool....
  • [Fit for Your Tool Kit]: Wheel puller set includes (1) floating swivel, (2) 5/16 by 4 inch (7.9mm x 101mm) bolts, (2) 1/4 by 3 inch (6.3mm x 76mm)....
  • [Blow-Molded Case]: Steering wheel puller tool harmonic balancer steering wheel puller kit comes in durable blow-molded plastic case to ensure....
Check Stock

5pcs Front End Service Tool 5-in-1 Ball Joint Separator, Pitman Arm Puller, Tie Rod End Tool Set for Front End Service, Splitter Removal Kit

  • ALL-IN-ONE TOOL KIT - Containing 5 adjustable tools for a wide range of domestic and import vehicles. Comes with 1x Ball Joint Separator, 1x Tie Rod and Ball Joint Remover, 1x Conical Pitman Arm Puller, 1x Pitman Arm, 1x Pitman Arm Puller, 1x portail custom moded case..
  • COMPATIBLE WITH FOLLOWING VEHICLES - The tool set allows this tool to be used as a pitman arm remover, ball joint separator, or tie rod end puller for many small, domestic rear-wheel-drive vehicles, import vehicles, and light trucks..
  • HIGH QUALITY - Extraordinarily tough and durable alloy means these tools can stand up to the toughest jobs. This front end service tool kit can remove the most stubborn ball joints, tie rod ends, and pitman arms..
  • MULTIFUNCTIONAL USE - Allows for easy removal of the most popular types of pitman arms, tie rods, and ball joints. The press-type ball joint separator allows for ball joint removal without damage to boots and other parts that fork-type removers may cause..
  • PORTABLE CARRY BAG - All-in-one Tool Set in a heavy-duty blow-mold case with handle and latches for secure storage, simpl....
Check Stock

Orion Motor Tech 3\ 4\ 6\ 3-Jaw Gear Puller Set for Removal of Bearings Pulleys Flywheels (GD)

  • Universal Removal Tool: This 3-jaw removal tool set works with your wrench, ratchet, or spanner as a gear puller, sprocket puller, bearing puller, pulley puller, flywheel puller and more, removing even rusted parts easily and—thanks to its even distribution of force—without damage..
  • Better Together: This professional or home tool kit includes three puller sizes to cover most applications: a 3 inch gear puller with a 2.3" reach and 3" max. spread.
  • a 4 inch gear puller with a 3" reach and 4" max. spread.
  • and a 6 inch gear puller with a 4.7" reach and 6" max. spread..
  • Versatile Reversible Design: Each of the three 3-jaw gear and bearing pullers can be reversed to pull parts from either the inside or outside as needed..
  • 45# Carbon Steel: All parts are made with premium heat-treated 45# carbon steel for maximum strength. The jaws are galvanized and the central screw coated with black oxide to provide superior corrosion resistance and long service life..
  • Satisfaction Guaranteed: Along with this gear and bearing removal tool kit's durable material and careful engineering, you can rest easy knowing that these gear pullers are backed by Orion Motor Tech's warranty and friendly customer service..
Check Stock