Reviews Harvester Header

J&D Productions, Inc. International Harvester IH Tractor Hat, red with Black mesh

Premium Quality Exhaust Heat Wrap: LIBERRWAY exhaust wrap is made from pulverized lava rock. The header wrap reduces heat under hood up to 50% and....
Effective Exhaust Header Wrap: Withstands 1400℉ direct heat and 2000℉ intermittent heat. Stronger and more durable for improved thermal....
Functional Header Wrap: Extremely pliable for a tight and secure wrap. Improves horsepower performance and can be used on car exhaust header wrap,....
Easy to Install: Before installing, soak the header heat wrap in water so that the fiberglass will not flying about. Wear gloves to avoid itching.....
What You Get: 2 rolls of 2 in (width) x 50 ft (length) x 1/16 in (thickness) header exhaust wrap, 20 pcs 0.3 in (width) x 11.8 ft (length) 304....

High grade alloy-steel material for durability and long wear capablities.
Induction hardened rails that offer superior resistance to rail wear and chipping.
Large diameter nose rivets to reduce the risk of rail spreading at the nose.
Engineered to match harvester powerheads for maximum performance.

Connector1: USB 3.0 Front Panel Socket / Connector2: USB 3.1 Front Panel Header.
The adapter is a converter to convert the available USB 3.0 header of a motherboard into a USB 3.1 header. Thus the USB 3.1 port of a housing can also....
Even the most up-to-date motherboards with AMD AM4 or Intel 2066 sockets are not always equipped with a USB 3.1 header. The adapter is the perfect....
The small converter is plugged into a USB 3.0 header that provides two USB 3.0 lanes. Thus, two data lines with 5 Gbps each are available, which are....
The converter thus provides a full-fledged USB 3.1 port..

Rated to 10,000 PSI! Locks on, stays on. Does not leak once locked on..
Hands free - does not pop off under pressure. Easily release from fittings with the thumb lever, even at extreme pressure..
Fits all standard Grease Guns - 1/8 NPT fitting. Fits all SAE and Metric Zerk fittings. Simply replace your existing coupler..
Over 3.5" of reach. Great for shielded PTO shafts, axles, harvester heads, U Joints and other recessed grease fittings..
Includes rebuild kit. Easily replace seal and jaws without replacing the coupler..

Sole per panel. Made of 15% cotton, 20% linen and 65% polyester, natural linen look. Drapery unlined. Heavyweight 500 gsm. Sunlight shading rate 85%..
WIDTH: For pinch pleat, goblet header, panel width is the width after pleats already set, we recommend 1.0-1.1 times wide of your curtain rod or track. For tab top and rod pocket header, we recommend fullness ratio 1.0-1.2 times wide of your curtain rod. For grommet header, we recommend fullness ratio 1.5-2 times to create the waves and folds when close the curtains. For flat hook and back tab header, we recommend fullness ratio 1.25-2 times wide of your curtain rod..
LENGTH: For grommet, rod pocket, back tab and tab top header, measure from the top of rod to where you want the bottom of the drapery to be (1/2″ above the floor, or approximately 6″ to 8″ below the window sill ). This is your finished top of pole to hem drop. For flat hook, pinch pleat and goblet header, measure from bottom of rings to top of floor or top of window sill, depending on desired window coverage. Subtract 1/2″ to get the panel length you need..
Fit for living room, bedroom, patio door, club, hospital, room divider..
Easy Care: Machine washable in cold water, use only non-chlorine bleach when needed, tumble dry l....