Reviews Flat Head Roofing Nails

3PLUS HCN45SP 11 Gauge 15 Degree 3/4\ to 1-3/4\ Coil Roofing Nailer

  • Drives 3/4-Inch to 1-3/4-Inch full head coil roofing nails.
  • Adjustable shingle guide for quick shingle spacing.
  • Integrated side skid pads prevent the tool from sliding off roof when placed on its side.
  • High-capacity magazine holds up to 120 coil nails at a time.
  • Tool free adjustable depth of drive for consistent and controllable nail fit.
  • Interchangeable trigger for single shot or bumper fire function..
Check Stock

PacTool RS501 Roof Snake Tool - Shingle Pry Bar - Heavy Duty Nail Remover Tool - Roof Shingle Remover - Professional Roofing Tools

  • COMMERCIAL CROWBAR: Replace old and worn-out composition roofing shingles in no time with our practical pry tool. Our roof snake makes removing and applying new shingles more accurate, efficient, and safer than traditional replacement methods..
  • ROOFING TOOLS AND EQUIPMENT: Never damage your roof again with this convenient pocket pry bar. Install new 3-tab shingles without bending or hitting surrounding shingles or accidentally striking your fingers with your hammer in the process..
  • HAND TOOLS: A must-have for all roofers, this tool is forged from high-strength steel and has a patented offset nail slot feature allowing you to align nails with the correct one-inch offset from the bottom edge of your current course..
  • NAIL PULLER TOOL: There is no need for a flat bar with this handy claw tip, Easily loosen and remove old, damaged shingles and nails by driving the claw end under the nail, rolling the nail out, and twisting the roof snake..
  • PACTOOL: Trusted for decades, we are the leaders in specialized construction, renovation, and remodeling designs. Our cutting-edge product line inspires craftspeople and DIYers to work smarter, measure better, and repair more efficiently..
Check Stock

STINGER 0136260 NailPac Cap Nails - 1 Electro Galvanized Nails with 1 Plastic Collated Caps 0136260 for use with CN100B & CN100 Cap Nailers

  • SUPERIOR HOLDING POWER - 1” (25mm) plastic collated caps and 1”x.083” (25mmx2.1mm) full round head ring shank nails holds underlayment securely.
  • EASY RELOADS - Contains 10 reels of 200 collated plastic caps and 10 coils of 200 nails which covers 25 square.
  • WHERe TO USE - Use corrosion-resistant electro galvanized nails in areas more than 3,000 ft (914m) from saltwater.
  • MEETS ASTM REQUIREMENTS - Cap nails meet ASTM F1667 requirements and exceed ASTM D3161 and D7869-17 for wind and UV resistance.
  • BEST PRACTICE UNDERLAYMENT FASTENER - Use exclusively with STINGER CN100B for the best practice installation of roofing underlayment.
Check Stock

Senco RoofPro 450 Coil Roofing Nailer

  • Drives 11 gauge (.120-Inch) , full round head roofing nails 3/4-Inch 1-3/4-Inch smooth shank..
  • Durable molded grip to reduce operator fatigue.
Check Stock

HBT HBCN45P 7/8" to 1-3/4" Coil Roofing Nailer with Magnesium Housing 11 GA Roofing Nail Gun

  • Drives 11 gauge full head coil roofing nails ranging from 7/8'' To 1-3/4''.
  • Selective actuation switch allows for either sequential or contact mode.
  • Tool-free adjustable depth control helps set nails properly.
  • adjustable shingle guide allows for quick and consistent shingle spacing.
  • Durable and lightweight magnesium housing helps reduce user fatigue.
  • Skid-resistant pads/wear guards for safety and tool protection.
  • contact safety With Carbide inserts for less wear and tear.
Check Stock

#8 x 1/2\ Stainless Philips Pan Head Sheetmetal Screw (1/2\ to 2\ Lengths in Listing) 100 Sheet Metal Screws (#8 x 1/2 Inch)

  • Dimensions: 5/16" Hex Head and ~9/16" EPDM washer - Shaft is .242" (#14) - Length under head 1".
  • #14 Sheet Metal roofing screws are galvanized for corrosion resistance.
  • Sharp T17 type point securely fastens metal roofing to wood structures quickly and easily.
  • For installing roofing on a house, porch, airplane hangar, shed, pole barn, shop, barn or lean-to.
  • Rough Estimation - regular roofing project should require 80 screws per 10 x 10 section of roofing.
Check Stock

Carpenter Air Tools CCN45 7/8\ To 1 3/4\ 15° Pneumatic Coil Roofing Nailer

  • The CCN45 drives 15° wire Collated roofing nails from 7/8 to 1-3/4 in length..
  • Contact firing mode for convenience and speed enabling smooth uninterrupted operation..
  • Ergonomic molded rubber grip ensures the tool fits comfortably in your hand reducing fatigue..
  • Durable and lightweight heat-treated aluminum housing for years of solid performance..
  • Holds a full coil of 120 roofing nails limiting the need for constant reloading and the tool free depth adjustment will help to make sure every nail is set perfectly..
Check Stock

meite 15 Degree Round Head 1-1/2-Inch × .120 Wire Weld Collated Smooth Shank Electro Galvanized Coil Roofing Nails 7,200 PCS/CASE (1 Box Pack)

  • 15 degree 1-1/2-Inch × .120 coil roofing nails.
  • For used in Bostitch RN46-1, Senco 455XP and other 15 degree coil roofing nailers.
Check Stock

#14 Metal Roofing Screws 250 Screws x 1-1/2 Galvanized Hex Head Sheet Metal Roof Screw Self Starting Metal to Wood Sheet Metal Screws with EPDM Washer for Corrugated Roofing

  • Dimensions: 5/16" Hex Head and ~9/16" EPDM washer - Shaft is .242" (#14) - Length under head 1-1/2".
  • Polyurethane coated screw head is painted to closely match many brands of metal roofing (color may vary).
  • #14 Sheet Metal roofing screws are galvanized for corrosion resistance.
  • Sharp T17 type point securely fastens metal roofing to wood structures quickly and easily.
  • For installing roofing on a house, porch, airplane hangar, shed, pole barn, shop, barn or lean-to.
Check Stock