Reviews Fitting Screw Thread

1/4-20 Brass Push in Threaded Insert 0.5\ Long (50 pcs)

  • 【Premium Quality 】 Used in various low strength materials, which can improve the wear resistance of bolt connections and avoid the damage of thread. The locking type wire screw sleeve can lock the screw into the threaded hole, so that the screw is not loose when subjected to shock vibration, which is better than the normal locking device..
  • 【Effect】 Because of a certain elastic, can make the load on the thread is more even, eliminate the screw and screw hole deviation between the pitch and tooth type, and can absorb vibration, thus increasing the screw thread connection strength and resistance to fatigue strength..
  • 【Material】 Made of high quality Stainless Steel, good corrosion resistance and never rust, durable to use,have a long time..
  • 【Special】 Wear resistant. Used for frequent disassembly, it can greatly improve the life of thread. Anti-loose. Especially for the aircraft and other products requiring high insurance coefficients..
  • 【Easy to maintain】 The damaged screw holes shall be put into the wire screw sleeve , which can be used again to avoid the possibility of damage to the workpiece..
Check Stock

Matte Black Trip Lever Tub Trim Kit Set with Trip Lever Overflow Face Plate No Putty Gasket,Trip Lever Bathtub Drain with Strainer Overflow and Matching Screws No Putty Installation by Artiwell

  • ...tiwell Tip-Toe Tub Trim Set Coming with High Quality Brass , Zinc and ABS Construction ,designed for Long-Lasting Durability, Improving coating technology to improve anti-flaked off performance ,withstands longer lasting soaking in water..
  • STANDARD DESIGN: Designed to fit most tub and baths with the threaded bushing fitting 1-1/2 inch ,1-3/8” inch bath shoe sizes. This Drain can fit both 1-1/2" coarse thread and 1-5/8" fine thread Drain Shoe Sizes. Screw the brass adapter bushing on the Bath drain , the diameter is 1-13/16" , can be fit 1-1/2" coarse thread. Screw the brass adapter bushing off the Bath drain ,the diameter is 1-5/8" , can be fit 1-5/8" Fine thread..
  • TRUSTED QUALITY: Be confident in the quality and construction of each and every one of our products. We ensure that all of our products are produced to regional, national industry standards. We are proud of the products we sell, you will be too..
Check Stock

Black Bolt Gauge SAE Metric Check a Thread Size FastenerLine 901303

  • 29° ACME Thread Gauge-The 29 degree stainless steel acme thread gauge is a single piece type and it is applied to measure thread and external thread tooth pitch.The acme thread gauge range:1-10TPI,the pitch:1,1-1/3,1-1/2,1-3/4,2,2-1/2,3,4,5,6,7,8,9,10.
  • Suitable for-Standard gauge for check the angle of screw cutting tools,check the width of screw cutting tools and set the position of screw cutting tools.
  • Material of stainless steel-This acme thread gauge is made by stainless steel.Not easy to rust and not easy to bend.You needn’t to use anti-rust oil or take any anti-rust ways.Just put the 29 degree acme thread gauge in a dry place and it won’t rust.
  • Clear scales-All the scales on the acme screw gauge are laser engraving,not painting and the acme thread gauge is not the copy of laser engraving. Don’t worry about the long friction will make the scale unclear.
  • Quality after-sale Service- If you are experiencing quality issues or any problems when you receive this acme thread gauge, please feel free to contact our customer service in time and let us know the issue. We offer further solution for you to your satisfaction.
Check Stock

142pcs Threaded Inserts Repair Kit, Stainless Steel Helicoil Type Wire Insert Installation Set

  • 【Premium Quality 】 Used in various low strength materials, which can improve the wear resistance of bolt connections and avoid the damage of thread. The locking type wire screw sleeve can lock the screw into the threaded hole, so that the screw is not loose when subjected to shock vibration, which is better than the normal locking device..
  • 【Effect】 Because of a certain elastic, can make the load on the thread is more even, eliminate the screw and screw hole deviation between the pitch and tooth type, and can absorb vibration, thus increasing the screw thread connection strength and resistance to fatigue strength..
  • 【Material】 Made of high quality Stainless Steel, good corrosion resistance and never rust, durable to use,have a long time..
  • 【Special】 Wear resistant. Used for frequent disassembly, it can greatly improve the life of thread. Anti-loose. Especially for the aircraft and other products requiring high insurance coefficients..
  • 【Easy to maintain】 The damaged screw holes shall be put into the wire screw sleeve , which can be used again to avoid the possibility of damage to the workpiece..
Check Stock

HVAZI 300pcs Metric M2 M2.5 M3 Stainless Steel Hex Socket Head Cap Screws Assortment Kit

  • High Quality 300pcs Metric M2 M2.5 M3 Hex Socket Head Cap Screws Assortment Kit.
  • Screw thread: M2/(2mm) with thread pitch: 0.4mm.
  • Screw thread: M2.5/(2.5mm) with thread pitch: 0.45mm.
  • Screw thread: M3/(3mm) with thread pitch: 0.5mm.
  • M2 different length:6MM,8MM,10MM,16MM,20MM.
  • M2.5 different length:6MM,8MM,10MM,16MM,20MM.
  • Made of 304 stainless steel for corrosion resistance..
  • 100% new,durable to use. Good Quality,Easy to install..
Check Stock

RIDGE WASHER Pressure Washer Surface Cleaner Nozzle, Replacement Thread Nozzle, 25 Degree, Orifice 1.5, 1\\/8 Inch NPT, 4000 PSI, 2-Pack

  • Include 2 pieces of pressure washer surface cleaner nozzles, made of 304 stainless steel, more durable and resistant..
  • ATTENTION: 1/8 inch NPT male thread fitting. The outsize diameter of thread is near to 3/8 inch. Orifice diameter is 1.5. Spray angle is 25 degree..
  • Universal replacement screw nozzle for surface cleaner. Max pressure is up to 4000 PSI..
  • In order to avoid nozzle blocked by sand or other debris, you can use water inline filter. If nozzle are blocked, you can remove the nozzle, clean with needle and rinse with fresh water..
  • If you have questions, contact us at any time. We provide a service of quick reply within 24 hours. Welcome to RIDGE WASHER to see other pressure washer accessories..
Check Stock

British Whitworth BSW & Metric Screws Bolts Pitch Measure Thread Gauge 51 Blades Gages

  • ITEM NAME-29 Degrees ACME Screw Pitch Gauge 16pcs set, measuring range: 1-12in.
  • GOOD FUNCTION- Screw Pitch Gauge Accurately measures T-Thread with thread blades of varied size.
  • Used for checking tool angle while cutting threads in metal turning lathes.
  • HIGH QUALITY MATERIAL-The Screw Thread Pitch gage is made of stainless steel, through quenching processing, strong hardness ,elegant appearance.
  • It won't get rusted easily and owns long lasting durability.
  • EASY TO USE- Each thread blade has a distinct saw-tooth shape and laser-engraved numbers on each piece for easy measurement and reading.
  • EASY TO CARRY- Folding design the Screw Pitch gage, when not in use each thread blade can be recovered, folded compact size, increased portability.
Check Stock

50pcs Stainless Steel Coiled Wire Helical Screw Thread Repair Insert Assortment Kit M8 x 1.25 x 1.5D Length

  • It is easy to maintenance, install a thread insert into a damage screw hole, then the screw hole can be used as normal, in order to avoid workpiece loss..
  • Used in low strength materials such as aluminum, magnesium, can avoid thread damage and get a good connection performance, to enhance connection strength and improve connection condition..
  • Used for parts that requires frequent removing, it can greatly improve service life and wear-resistance of screw thread..
  • Because of a certain elasticity, thread insert can even the load distribution on each thread, eliminate pitch and tooth deviation between screw and screw hole..
  • We strive to provide you with high quality and convenient service. You are welcome to contact us if you have any problem about our product, we will give you a satisfactory reply..
Check Stock

DIY Tool Kit Jig Winding Set,Ceramics Tweezers,Cutter,Folding Scissors Brush Screwdrivers with A Carrying Case

  • 1pcs Thick Acrylic stand display for 510 screw thread RDA tank, 9pcs silicon anti-slip ring , the 9pcs silicone suits for different size of tank ..
  • there are 9pcs 510 screw thread for RDA tanks , 9pcs silicone anti-slip rings (3pcs in 25mm diameter , 3pcs in 22mm diameter , 3pcs in 18mm diameter ).
  • the 9 holes are with 510 thread screw , it suits any 510 thread screw tank.
  • screw the 510 RDA tank on the stand . it will not fall off , keep your tanks all standing in order .NOT in a mess ..
Check Stock