Reviews Fiber Cement Sealer

KILZ Klear Primer, Interior/Exterior, Clear, 1 Gallon

This high-performance clear primer is formulated to bond and seal porous and chalky interior and exterior surfaces with a tough, flexible, and breathable clear coating..
KILZ Klear is an alkali-resistant clear primer and sealer. It helps protect topcoats from "hot" alkali found in masonry, cement and plaster and can be applied to fresh concrete with pH less than 13. KILZ KLEAR dries to touch within 30 minutes and dries to recoat in an hour..
Incredibly versatile, KILZ Klear primer can be used to seal porous surfaces and promote adhesion with a transparent flat finish that is particularly effective for same color painting..
Use for sealing drywall, plaster, wood, galvanized, aluminum, architectural plastics, masonry and brick. Soap and water cleanup and dries fast - ready to recoat in 1 hour. Use on properly prepared surfaces free of dust, grease, chalk, rust and peeling paint. Mix well before using. Apply with brush, roller, or spray.Recommended Application Temperature: 50-90.
This is a 1-gallon can of KILZ Klear Multi-Surface Latex Transparent Primer, Sealer, and Binder. It creates a tough, flexible clear primer film. One gallon covers 300 to 400 square feet..

Long-lasting, alkali-resistant mesh will withstand corrosive effects of the alkaline present in cement board joint finishing, lightweight concrete panel seaming and crack repair, block foundation, and reinforcement for fiber cement, and concrete stucco. Heavier fiberglass yarns for more strength than regular mesh tapes..

Coverage varies with the surface texture, temperature of the concrete and ambient conditions.
Allow a minimum of 4 hours drying/reaction time.
Product can be used on interior and exterior cement and concrete surfaces.
Using a concrete sealer is optional with concrete acid stains.

【Anti-cracking】- Mixing fiberglass and mortar together, the irregular distribution of fiberglass in the mortar enhances the toughness of mortar, and inhibits the formation of fine cracks..
【Waterproof and Impermeable】- A large number of fiber filaments increase the density of cement, which can effectively solve the problem of penetration. It is very suitable for wet place such as basements, pond, Exterior wall..
【Impact Resistance】-High-strength fiber filaments are attached to each other as a dense net to hold the cement tightly. It can effectively enhance the impact and seismic performance of cement..
【How to Use】-Evenly mix sand, cement and fiberglass together, then add an appropriate amount of water, and finally stir (the stiring time is 30-60 seconds longer than without fiberglass).
【Dosage】-Use 1 lb. (1 pkg) per cubic yard (27 cubic feet) of concrete. You can add a little more in the area with strong impact or severe freeze-thaw.

BONUS installation Kit and double-sided honing stone included! Designed to cut laminate, solid wood and engineered flooring up to 15mm (5/8″). will also cut vinyl tile and fiber cement siding such as hardy plank..
Designed to cut laminate, vinyl, solid wood and engineered flooring up to 15mm (5/8″). will also cut fiber cement siding such as hardy plank.
Angle gauge allows for cuts up to 45 degrees.
Quiet, dust free operation, No electricity required.

The only approved James Hardie polycrystalline diamond (PCD) tipped fiber cement saw blade.
The PCD triple chip design offers up to 60-times longer cutting life than standard carbide blades.
The laser cut thin kerf design gives fast and precise cuts with less dust and waste..
Anti-vibration design stabilizes the blade and reduces noise while cutting and Non-Stick Perma-Shield coating to reduce heat.

BONUS installation Kit and double-sided honing stone included! Designed to cut laminate, solid wood and engineered flooring up to 15mm (5/8"). will also cut vinyl tile and fiber cement siding such as hardy plank..
Designed to cut laminate, vinyl, solid wood and engineered flooring up to 15mm (5/8"). will also cut fiber cement siding such as hardier plank.
Angle gauge allows for cuts up to 45 degrees.

VViViD Black Forged Brushed Carbon Fiber Vinyl is a premium automotive vinyl, specially engineered for DIY’ers. This durable film is ideal for long-term fleet and motorsport marketing applications, and provides a lightweight, economical alternative to paint..
At 3.9mils in thickness, our Forged Brushed Carbon film will stretch and conform to any shape, yet is thick enough to resist wear and tear, resulting in a longer life-span than most other automotive vinyls..
Our Forged Brushed Carbon Fiber vinyl incorporates cutting edge technologies, such as VViViD Air Release, VViViD Resist, and VViViD Heat Fuse, enabling DIY’ers to wrap their car with professional quality results. See the product description below for more detailed info on these technologies..
Forged Brushed Carbon Fiber specifications: Application: Dry. Adhesive : Solvent-based, repositionable, permanent adhesive. Life: This vinyl is expected to easily last 5-7 years outdoors..
VViViD Forged Brushed Carbon Fiber can be installed using 3M 94 Primer and 3M Edge sealer. Though not mandatory, these products will promote adhesion and add life to your vinyl. The sealer or primer will not remove the glue, deform the vinyl, or ruin the texture, unlike cheaper quality films..

Finally, a way to hang items on your fiber cement board siding without drilling!.
Installation video: https://youtu.be/6RutcQ1IBhw.
These hooks are made in the USA and are patent pending..
Hang items on your fiber cement board siding without drilling or any other damage..