Reviews Dust Sensor Module

ACEIRMC VL6180 VL6180X Range Finder Optical Ranging Light Sensor Module Gesture Recognition Sensor I2C Interface 3.3V 5V Emitter Ambient Light Sensor for Arduino I2C (4)

VL6180 VL6180X Range Finder Optical Ranging Sensor Module Gesture Recognition Sensor.
VL6180 is a time-of-flight ranging sensor. The sensor contains a very small laser source and a matching sensor..
I2C interface for device control and data, two programmable GPIOs..
VL6180X can detect the "time of flight" or the time required for the laser to recover the sensor to calculate the distance..
VL6180 VL6180X Range Finder Optical Ranging Sensor Module for Arduino I2C Interface 3.3V 5V gesture recognition.

Simplify connecting a waterproof temperature sensor to your project with this adapter module kit.
Pull-up resistor included on the adapter module, an external resistor is not required to connect directly to the GPIO of the Raspberry Pi.
Waterproof digital temperature sensor DS18B20 on 100cm cable with adapter module.
Measure the temperature directly in water or soil.
DS18B20 Wiring: Red = VCC, Yellow = Data, Black = GND.

Specially designed for Microbit board. This kit includes a keyestudio sensor shield fully compatible with micro bit and other commonly used 37 kinds of sensor modules. It's compatible with both microbit v1.5 and v2, microbit board not include!.
Designed to learn electronics programming. Great hands on STEM kit to get started with the micro bit. The product needs to be debugged before use, such as an LED display module. Please use an external power supply and debug the backlight brightness..
The kit gives 37 kinds of common sensors, such as Digital LED Module, Analog Temperature Sensor, Photocell Sensor, Ultrasonic Module etc, allow you make a lot of interesting projects like Traffic Light, Magnetic Check, Temperature Test, Joystick Test, Photo-interrupter Test, Alcohol Detection and so on..
We have detailed tutorial( included introduction, wiring diagram, test code, driver installation, Example Projects...... Step by step to explain how to use on our wiki page..
Solder is very clean, everything is aligned nicely, all boards are well packed after function, voltage, current testing, protected in a beautiful box. Up to FCC and CE Standard: made from environmentally friendly components and materials..

Model: 1*Laser Receiver Sensor Module+ 1* KY-008 Laser Transmitter Module.
Laser Receiver Sensor Module uses the non modulated laser receiver, please use in the room where without the light, the sunlight or other lamps and lanterns will interfere, suggested in the dark environment use..

Simplify connecting a waterproof temperature sensor to your project with this adapter module kit.
Pull-up resistor included on the adapter module, an external resistor is not required to connect directly to the GPIO of the Raspberry Pi.
Waterproof digital temperature sensor DS18B20 on 100cm cable with adapter module.
Measure the temperature directly in water or soil.
DS18B20 Wiring: Red = VCC, Yellow = Data, Black = GND.

This RCWL-0516 module has the characteristics of high sensitivity, high induction distance, high reliability, large induction angle, wide power supply voltage range, etc. it is widely used in various kinds of human body induction lighting and alarm and so on..
Compatible with Arduino Raspberry PI,Human Rat Cat Detector for nodemcu for wemos etc..
It also can detect human, cat, rat, water.
Wide operating voltage range: 4.0-28.0V, output 3.3V power supply.
RCWL-0516 RCWL 0516 Microwave Radar Sensor Human Sensor Body Sensor Module.
What you will get: 12pcs RCWL-0516 Module, 40 pins header.

This ir transmitter sensor module is directly launched by a single tube, it requires waveform modulation through the program..
It is suitable for infrared communication, infrared remote control, apply to a variety of platforms including for Arduino/51/AVR/ARM.
With signal indicating LED, easy to observe and debug..
Pin Definitions: (1) Output (2) Vcc (3) GND.
IR Infrared Transmitter Module Ir Digital 38khz Infrared Receiver Sensor Module For Arduino Electronic Building Block.

Communication: standard IIC communication protocol.
✹✹This sensor module is a small, 3 a-xis accelerometer and 3 ax-is gyroscope integrated in a single package..
✹✹The BMI160 is a small, low-power, low-noise 16-bit inertial measurement unit designed for use in mobile applications such as augmented reality or inland navigation, which require high-precision, real-time sensor data..
✹✹In full operation mode, with both the accelerometer and gyroscope enabled, allowing always-on applications in battery-powered devices..
✹✹3PCS 6DOF Bosch GY-BMI160 Module 6-axis Acceleration Gyro Gravity Sensor for Arduino.

Received great ideas from our customers and adopted in this upgraded kit. Removed useless modules heartbeat sensor, two of the hall sensors, one of the dual-color sensor. Add useful modules like GY-521 accelerometer module, LCD1602 screen, DS1307 real time clock module etc..
Professional 37-in-1 Sensor Module Kit, NOT ONLY compatible for BUT ALSO compatible for raspberry pi RPi 3 2 Model B A A+ B+, Complete Update and common models for Mega 2560 starter kit..
Standard interface can be controlled directly by microcontroller ( 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic)..
Upgraded tutorial only for R3, for MEGA2560 R3, for NANO in CD, listing paper, resistors pack only from Elegoo Team. There are tutorials in the CD that comes with. or download the tutorials online from the official website..
100% compatible with Arduino official IDE, Raspberry Pi and STM32..