Reviews Double Sheave Pulley

Martin 3020 2 Taper Bushing, Sintered Steel, Inch, 2\ Bore, 4.25\ OD, 2\ Length

Taper bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
Sintered steel for greater strength and resistance to wear than steel.
Keyed to the shaft to prevent the shaft from rotating in the bushing.
Interchangeable with taper bushings from various manufacturers.

Mytee Products Snatch Block with Hook WLL 2 Ton 3 Sheave 3/8 Inch Wire Rope Wrecker Roll Back Recovery

The snatch block is a pulley system with covered and protected yet removable sides..
Snatch blocks or pulleys are used to change the direction of the pull to a different angle relative to a fixed point..

Mytee Products Snatch Block with Hook WLL 8 Ton 6 Sheave 3/4 Inch Wire Rope Wrecker Roll Back Recovery

The snatch block is a pulley system with covered and protected yet removable sides..
Snatch blocks or pulleys are used to change the direction of the pull to a different angle relative to a fixed point..

Martin 2517 1 1/2 Taper Bushing, Sintered Steel, Inch, 1.5\ Bore, 3.375\ OD, 1.75\ Length

Taper bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
Sintered steel for greater strength and resistance to wear than steel.
Keyed to the shaft to prevent the shaft from rotating in the bushing.
Interchangeable with taper bushings from various manufacturers.

Martin 1008 5/8 Taper Bushing, Sintered Steel, Inch, 0.62\ Bore, 1.386\ OD, 0.875\ Length

Taper bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
Sintered steel for greater strength and resistance to wear than steel.
Keyed to the shaft to prevent the shaft from rotating in the bushing.
Interchangeable with taper bushings from various manufacturers.

Martin 2517 2 7/16 Taper Bushing, Sintered Steel, Inch, 2.44\ Bore, 3.375\ OD, 1.75\ Length

Taper bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
Sintered steel for greater strength and resistance to wear than steel.
Keyed to the shaft to prevent the shaft from rotating in the bushing.
Interchangeable with taper bushings from various manufacturers.

Martin 2517 1 1/4 Taper Bushing, Sintered Steel, Inch, 1.25\ Bore, 3.375\ OD, 1.75\ Length

Taper bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
Sintered steel for greater strength and resistance to wear than steel.
Keyed to the shaft to prevent the shaft from rotating in the bushing.
Interchangeable with taper bushings from various manufacturers.

Martin 2012 1 5/8 Taper Bushing, Sintered Steel, Inch, 1.63\ Bore, 2.75\ OD, 1.25\ Length

Taper bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
Sintered steel for greater strength and resistance to wear than steel.
Keyed to the shaft to prevent the shaft from rotating in the bushing.
Interchangeable with taper bushings from various manufacturers.

Martin 2012 1 1/8 Taper Bushing, Sintered Steel, Inch, 1.13\ Bore, 2.75\ OD, 1.25\ Length

Taper bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
Sintered steel for greater strength and resistance to wear than steel.
Keyed to the shaft to prevent the shaft from rotating in the bushing.
Interchangeable with taper bushings from various manufacturers.