Reviews Discharge Tubing

VEVOR Bottled Water Dispensing System 20 ft Water Dispensing Pump System with US Plug 115V AC Perfect for 5 Gallon Bottle Single Inlet

【40 PSI WATER PUMP】- All the parts in contact with liquid are made of food-grade material. This type of water pump can provide power for 3-6....
【EASY FOR INSTALLATION】- Quick connect port speeds installation and replacement of suction and discharge tubing. Compact size for easy mounting.....
【USER-FRIENDLY DESIGN】- Equipped with noise dampening rubber feet to minimize noise pollution. Full automatic, operate when there is water, stop....
【GOOD PROTECTION】- Thermal protection prevents overheating, protecting the pump and control box from damage. It provides dependable run dry....
【WIDE APPLICATION】- This water pump can be widely used in refrigerator, water and ice makers, coffee makers, espresso makers, water dispensers,....

...the bubble stone in the incubator to provide oxygen. When the brine shrimp has hatched, open the trim valve at the bottom of the incubator to collect brine shrimp. Note that the direction of the inlet and outlet of the check valve must be installed correctly with the pipe, otherwise the air pump will not be able to discharge air..
The second way to provide oxygen to the brine shrimp from the bottom hole of the incubator. Please note the direction of the inlet and outlet of the check valve and the pipe must be installed correctly, otherwise the air pump will not be able to output air, and the trim valve needs to be opened. When the brine shrimp has hatched, first turn off the trim valve, then pull out the air pump tube from the trim valve, and then open the trim valve to start collecting brine shrimp.

Excellent choice for large size ponds up to 15,000 gallons. Whisper Quiet Operation: Reliable, Oil Free and Extremely Energy Efficient..
Includes: (4) 8" Round Weighted Air Diffusers. 80' of 3/8" Weighted Tubing. Necessary Fittings & Hardware. Discharge Outlet: 5/8".
Output: 5.3 CFM. Maximum Depth 15'. Noise Rating (dB) 38. Volts 120. Watts 125.
Frequency (Hz) 60. Dimensions (L x W x H) 10" x 8" x 10". (CFM = Cubic Feet Per Minute)..
Indoor / Outdoor Use. 2 Year Warranty. Ships Fast and Free Ground Delivery.

APPLICATIONS: ideal for collecting, detecting, and automatic removal of condensate from air conditioning equipment, dehumidifiers, high efficiency furnaces, condensing boilers, and other equipment.
galvanized steel "quick install" wall mount bracket.
rubber feet for vibration noise dampening.
INCLUDES OVERFLOW DETECTION SWITCH: dual function NO and NC operation.
shuts off equipment or can be attached to audible or visual alarm or security system.
AUTOMATIC OPERATION: vertical centrifugal pump design activates when condensate reaches 2.2 inches.
shuts off when condensate falls to 1.6 inches.
SPECIFICATIONS: 1/30 HP, 115 Volts, 60 Hz., 1.5 Amps, 93 Watts, 3/8-inch discharge, check valve included, 84 GPH at 1-ft. lift, 21 ft. shut-off, maximum 9.1 PSI.

...the bubble stone in the incubator to provide oxygen. When the brine shrimp has hatched, open the trim valve at the bottom of the incubator to collect brine shrimp. Note that the direction of the inlet and outlet of the check valve must be installed correctly with the pipe, otherwise the air pump will not be able to discharge air..
The second way to provide oxygen to the brine shrimp from the bottom hole of the incubator. Please note the direction of the inlet and outlet of the check valve and the pipe must be installed correctly, otherwise the air pump will not be able to output air, and the trim valve needs to be opened. When the brine shrimp has hatched, first turn off the trim valve, then pull out the air pump tube from the trim valve, and then open the trim valve to start collecting brine shrimp.

Thermally protected motor is UL and CSA listed.
Includes two 1-1/8” diameter inlet openings.
Product 1: PUMP WITH SAFETY SWITCH: Includes safety switch which can be connected to shut down the air conditioner condenser or wired to an alarm to warn of possible tank overflow.
Discharge is a 1/4" FNPT or 3/8" O.D. barbed tubing adapter.
Product 2: SimpleAir’s Clean Flow Tabs are a simple method to maintain free-flowing drain lines associated with all HVAC systems.
Product 2: Unique tablets are time released when water activated.
Product 2: Tabs prevent common growth in drain lines that could lead to clogging of drain lines and overflow.
Product 2: Each tablet lasts up to 2 months.

MADE IN THE USA - NO PLUMBING REQUIRED – Comes with 2 John Guest quick connect fittings on both sides. Fits all 1/4″ plastic flex tubing and flexible Copper tubing, used for water supply to ice makers, refrigerators, etc. (1/4” JG also fits the 1/8″ PEX TUBING as its O.D. is the same as 1/4” tubing.) DOES NOT FIT BRAIDED HOSES..
MADE IN THE USA - NO PLUMBING REQUIRED – Comes with 2 John Guest quick connect fittings on both sides. Fits all 1/4″ plastic flex tubing and flexible Copper tubing, used for water supply to ice makers, refrigerators, etc. (1/4” JG also fits the....

Punch holes in supply tubing for easier insertion of ¼ in. barbed fittings and emitters with ¼ in. barbed inserts.
Works anywhere along the length of supply tubing where you want to insert a micro fitting or dripper.
The Hole Punch Tool punches a hole in supply tubing to insert fittings to connect tubing or drippers with barbed inserts.
Holds ½ in., 5/8 in., and 0.710 in. supply tubing to punch holes to fit ¼ in. barbed fittings and emitters with ¼ in. barbed inserts.
Use with ½ in., 5/8 in., or 0.710 in. Supply Tubing to punch holes.
Hand-held tool is designed with a comfortable pistol grip for strain-free use.
Metal hole punch tip penetrates tubing wall when handgrip is pressed.
Sliding shelf on tubing rest slides out to accommodate larger sized tubing.
Comes with one Pistol Grip Hole Punch Tool.

Heavy Duty Hose Cutter – The heavy duty cutter can cut through PETG tubing as effortlessly as you would cut flexible PVC tubing. Easily cut PETG rigid tubing without the need for a saw..
PETG Easy Bending Tool – This tool allows you to easily bend PETG tubing at an angle between 0 and 180 degrees. Just heat the tubing with the bending rubber inserted, insert the tube into the tool and bend it to the required radius. This simple tool takes the guess work and difficulty out of bending rigid tube. (Suitable for 12-14mm outer diameter tubing).
Bending Rubber – Solid rubber extrusion for bending PETG tubing. Insert into the tube before bending, to stop the PETG tube kinking, or deforming. (Bending rubber diameter is 10mm).
PETG Chamfer Tool – Quickly chamfer the edges of PETG tubing by using this handy tool. Just insert the tubing and turn anticlockwise..
PETG Edging Sandpaper – Ideal for sanding the edges of PETG tubing, after using a chamfer tool..