Reviews Din Rail Analog Output Module

ACEIRMC 8pcs HX711 Weighing Sensor Dual-Channel 24 Bit Precision A/D Module Pressure Sensor for Arduino Raspberry Pi Microcontroller

  • Analog Current Meter Module. Transformer can only sense AC.
  • This electricity sensor is based on TA12-100 current transformer, which can transform AC signals of large current into small amplitude signals..
  • 3-wire electronic block interface, input 5V - GND. S pin is the output analog voltage value..
  • You can use jumpers to select the parallel output of the output to adjust the range of analog values that are output..
  • On-board 3P and 4P connecting interface for current signal output can be easily connected with your MCU development board.
Check Stock

GRAYHILL 70M-IAC5 I/O Module

  • 4 DPDT signal relay module. TAKAMISAWA RY24W-K high quality relays, switch contact material - gold overlay silver-palladium..
  • Darlington transistor circuits drive relay coil, LED indicator for each relay channel..
  • High quality screw terminal block. FR-4 fiber glass PCB, dual copper layers..
  • Taiwan DINKLE fireproof nylon material DIN rail mount carrier (not China low quality carrier), can support width 35mm / 32mm / 15mm rail, and the carrier can be taken apart for panel mount use..
  • Datasheet: https://images-na.ssl-images-amazon.com/images/I/91Ml0Tph-rL.pdf.
Check Stock

Juried Engineering LM339N LM339 Quad Differential Comparator Industrial Grade Breadboard-Friendly IC DIP-14 (Pack of 5)

  • SINGLE-CHANNEL: TLV3501 is a single-channel high-speed push-pull output comparator, delay is 4.5ns, supply voltage: + 2.7V to + 5.5V.
  • FRONT SHAPING MODULE: This module can be for a wide range of voltage signal shaping period, as the frequency, phase difference time domain measurements and other front-end conditioning module.
  • CMOS AND TTL: Rail-to-rail output can directly drive a CMOS or TTL logic.
  • EASY TO OPERATE: Without threshold setting, the sine wave, square wave and triangular wave can be transformed into square wave, which can be used easily without debugging.
  • GREAT EXTENSIBILITY: At the same time, it has great extensibility, just change a small amount of the original.
Check Stock

FainWan 3Pcs High Sensitivity Microphone Sensor AVR PIC Sound Detection Module for Ar-duino

  • The module has 2 outputs: AO, analog output, real-time output microphone voltage signal.
  • DO, when the sound intensity reaches a certain threshold, it outputs high and low level signals, [threshold-sensitivity can be adjusted by potentiometer].
  • There are 3mm mounting screw holes, which are powered by a 5v DC power supply..
  • There is an analog output with a threshold flip level output.High sensitivity microphone with high sensitivity..
  • There is a power indicator and the comparator output has an indicator..
  • Package include: 3Pcs High Sensitivity Microphone Sensor.
Check Stock

0-10V Signal Isolation Module, S-10V10V Analog Quantities Voltage Signal Isolation Module for PLC/MCU Isolating High Voltage or Current (Voltage) Signals

  • ➤【DC12-32V】- This isolation module need two complete independent DC12-32V power supply..
  • ➤【Main function】- Main function is input 0-10V analog voltage signal,after isolation, output 0-10V analog voltage signal..
  • ➤【Scope of Application】- Used to isolate high voltage or strong interference voltage or current (voltage) signal then transferred to PLC or controller MCU, isolating controlling end and controlled end, to assure stability and anti-interference ability of system..
  • ➤【Use】- It will has better performance if install this module and controller in a metal box and box is grounded..
  • ➤【Note】- The potentiometer is used to amend corresponding relation of output voltage. Output voltage can be fine adjusted and calibrated, normally it has already been calibrated..
Check Stock

CZH-LABS DIN Rail Mount 8 Amp Solid State Relay SSR Module in 4~32VDC Out 100~240VAC 8 Channels

  • MOC3043 Phototriac and BTA12-600B triac (the heatsink is electrically insulated)..
  • Input Action Voltage DC 3 to 32V. LED indication for each channel. Anti-reverse protection diode..
  • Output Load Voltage range AC 100 to 240V (50/60Hz). Maximum on-state average current: 8 Amp, maximum on-state current 12 Amp (< 10 seconds). Isolation: Phototriac. Zero cross: Yes..
  • Terminal Block: Wire range: 24 ~ 12 AWG / 2.5mm square. Strip length: 7mm. Screws - M2.5, steel, Cr3+ Zn plated. Pin header and Cage - Brass..
  • DIN rail mount, Taiwan DINKLE fireproof nylon material DIN rail mount carrier (not China low quality carrier), can support width 35mm / 32mm / 15mm rail. FR-4 fiber glass PCB, dual copper layers..
Check Stock

CZH-LABS Screw Terminal Block Breakout Module Board for Arduino MKR.

  • DIN Rail Mount Pluggable 8x3 Position 10A / 300V Screw Terminal Block Distribution Module..
  • Input terminal: Screw terminal block, pitch 5.0mm/0.197.
Check Stock

Morris Products 87124 Voice/Data and Expansion Module

  • DIN Rail Mount 4 x 2 Positions Banana Jack Breakout Board Module..
  • A and B position termianl blocks, maximum current 20 Amp (each position). Pitch 7.62mm/0.3.
Check Stock

Electronics-Salon DIN Rail Mount 20 Position 30A / 300V Screw Terminal Block Distribution Module.

  • DIN Rail Mount 20 Position 30A / 300V Screw Terminal Block Distribution Module..
Check Stock