Reviews Dc Shunt Motors

Fielect 2Pcs 6V DC Motor with Wire 7000RPM Micro Motor Electric Motor Round Shaft for RC Boat Toys Model DIY Hobby

【Dimension】 - Shaft Diameter: 3.17mm/0.12".
【Features】- DC micro motor is durable, stable performance, shockproof, wear-resistant, and high precision. It is an excellent substitute for rusty or damaged DC motors on the machine.
【Material】 - The electric motor is made of metal, and the output shaft is made of high-hardness copper, which has good toughness and impact resistance.
【Application】 - Micro motors are used in electronic game machine printers, rear-view mirrors, headlight beam level adjusters, car toys, DIY hand drills, electronic equipment, etc.

PARAMETER — working voltage DC 3.3-30V.
DUAL MODE — the signal generator has 2 modes, PWM mode (default) & pulse mode..
APPLICATION — the signal generator module can be used to generate square wave rectangular wave signals for controlling DC motors or stepper motor driver.
for servo motors, stepper motors, electric jaws, PLC pulses replacement, etc..
PROTECTION — with anti-reverse protection, 5.08mm terminal wiring..
EASY TO OPERATE — the signal generator can control start or stop, it can also connect the external switch to control the output signal ON/OFF..

PARAMETER --- measuring voltage DC 4.5V-100V.
APPLICATION --- monitoring storage battery, solar panel, model railroad, RV, motorcycle, house batteries, motor, etc..
DISPLAY --- 0.39'' crisp and bright LED screen displays voltage & current value..
CALIBRATION --- with voltage & current calibration potentiometer..
NOTE --- the shunt should be connected when wiring, otherwise the meter will be burnt..

... simply as a DC 100 amp circuit breaker. This is a 12-48 volt DC (Direct Current) fuse breaker & CANNOT be used IN ANY AC (Alternate Current) OR HOUSEHOLD APPLICATION..
Be sure to consult your owner's manual when being used for your trolling motor plug and receptacle. Typically a 100 amp fuse is used on 12V trolling motors with 30, 40, or 45 lbs of thrust, 24V trolling motors with 70 lbs of thrust, & 36V trolling motors with no more than 100 lbs of thrust. A pair of 6 AWG copper lugs are included in this kit, but please verify that a AWG gauge trolling motor wire will be thick enough to handle your specific volt trolling motor plug..
Always consult a 12-48V DC wiring specialist if you are unsure about how to determine what type (this is a DC), amp (this is a 100A), and volt circuit breaker you require for your vehicle & vehicle accessories. A 1-300 amp circuit tester can be used to determine the draw of an accessory during initial, peak, and normal operation of the accessory, but this inline breaker is not a substitute for a sound professional installation. Always consult a professional before installation..

Motor drive module is ideal for use in battery-powered smart car, toy cars, robots..
Dual H-bridge motor driver, can drive two DC motors or a 4-wire two-phase stepper motor..
Supply voltage 2V -- 10V, can drive two DC motors or a 4-wire 2-phase stepper motors ,can achieve forward rotation or reverse rotation, it is possible to adjust the rotation speed..
Dual 1.5A * 2, the peak current to be 2.5A, built-in thermal protection circuit, do not be afraid motor stall burned, automatic recovery after the temperature dropped..
Use of imported original chip, built-in low on-resistance MOS switch, minimal heat, no heat sink, small size, low power consumption, is ideal for battery powered..

Driven part of the input voltage VS: VIN Input 6.5 ~ 12V, PWRIN 4.8 ~ 35V input..
The L298P shield DC motor driver has PWM speed control mode.
Adopt dedicated high-power motor driver chip L298P which can directly drive two DC motors with drive current up to 2A..
Stack design can be directly plugged into the Arduino, easier to use..

L298N as Main driver chip L298N, strong driving ability, strong anti-interference, low calorific value, afterflow diode protection, more stable and reliable for Arduino projects, Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability..
Double H bridge design, can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors, high efficient, To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage..
Driving DC motor Because the module is drived by double H bridge,it can drive two motors simultaneously.Input the following driving timing from IN1-IN4 then the speed and direction of the stepper motor can be controlled..
Easy to Use No assembly required. This L298N board comes ready to go. Just wire up motors and power, easy to use..
Wide Usage Great for DIY Smart Car Robot Power MEGA R3 for Mega2560 Duemilanove, if driving voltage is more than 12V, use external standard 5volt TTL outputs to switch the H-bridge circuits..

MINIMALIST STYLE: This 52-inch indoor ceiling fan has 3 powerful blades to make your home more comfortable.
their walnut finish attractively compliments any home decor from rustic industrial to minimalist.
REVERSIBLE FAN: It has 3 blades designed for high volume air movement and rotates in reversible direction for changing seasonal needs and has remote controlled operation..
REMOTE CONTROL: The convenient remote control allows you to adjust this fan's 6 speeds and 3 timer settings (1/4/8 hr.) from anywhere around your room, whether lying in bed, eating at the dining room table, or relaxing on your living room couch.
DC MOTOR: DC motor is energy efficient and ETL listed and has convenient wall holder for remote storage. These fans save on operating costs with energy efficient DC motors. They save up to 65% more efficient than traditional AC fan motors..
NOTICE: The DC motor can only work properly after the blades are installed (with load), so we recommend that you also install the blades during the installation test.

This 4 mecanum wheels is compatible with all DC motors with a motor shaft diameter of 6mm..
78mm All Black mecanum wheel made of steel and rubber roller, 4pcs can load no less than 60KG..
4pcs DC motor is 12V 178rpm, rated torque is 6.5KG.CM, 4pcs can load no less than 20KG..
The plate made of 3mm aluminum alloy materials, not easy to deform..
What you get: 1pcs frame, 4pcs motors, 4pcs mecanum wheels with couplings, 4pcs motor brackets, motor cables, screws..