Reviews Dc Electronic Motors

TE CONNECTIVITY / POTTER & BRUMFIELD T92P7D22-12 POWER RELAY, 12VDC, 30A, DPST-NO, FLANGE

  • Electromagnetic relays are widely used: household air conditioner compressor motors, fan motors, cooling pump motors, starter relays for car starters, spur relays, motors, generator circuit breakers, industrial relays, etc.
  • Product Name: Electromagnetic Power Relay.
  • Red mechanical indicatoe:It can intuitively judge whether the relay is attracted.
  • LED signal lamp : It can judge the AC or DC coil, and judge whether the coil is energized.
Check Stock

PWM Pulse Generator, DROK Dual Mode Adjustable Function Generator DC 3.3-30V 1-150kHZ 1-9999 Variable Pulse Width Frequency Duty Cycle Square Rectangular Wave Signal Generator Module with Case

  • PARAMETER — working voltage DC 3.3-30V.
  • DUAL MODE — the signal generator has 2 modes, PWM mode (default) & pulse mode..
  • APPLICATION — the signal generator module can be used to generate square wave rectangular wave signals for controlling DC motors or stepper motor driver.
  • for servo motors, stepper motors, electric jaws, PLC pulses replacement, etc..
  • PROTECTION — with anti-reverse protection, 5.08mm terminal wiring..
  • EASY TO OPERATE — the signal generator can control start or stop, it can also connect the external switch to control the output signal ON/OFF..
Check Stock

Truck Upfitters Surface Mounted 100A Circuit Breaker (12V-48V, 100 Amp) for DC Automotive and Marine/Boat use: Main Power Breaker, Audio, Winches, Solar, Lighting, Electric Motors & Other Accessories.

  • ... simply as a DC 100 amp circuit breaker. This is a 12-48 volt DC (Direct Current) fuse breaker & CANNOT be used IN ANY AC (Alternate Current) OR HOUSEHOLD APPLICATION..
  • Be sure to consult your owner's manual when being used for your trolling motor plug and receptacle. Typically a 100 amp fuse is used on 12V trolling motors with 30, 40, or 45 lbs of thrust, 24V trolling motors with 70 lbs of thrust, & 36V trolling motors with no more than 100 lbs of thrust. A pair of 6 AWG copper lugs are included in this kit, but please verify that a AWG gauge trolling motor wire will be thick enough to handle your specific volt trolling motor plug..
  • Always consult a 12-48V DC wiring specialist if you are unsure about how to determine what type (this is a DC), amp (this is a 100A), and volt circuit breaker you require for your vehicle & vehicle accessories. A 1-300 amp circuit tester can be used to determine the draw of an accessory during initial, peak, and normal operation of the accessory, but this inline breaker is not a substitute for a sound professional installation. Always consult a professional before installation..
Check Stock

6 Pack Mini L298N DC Motor Driver, MELIFE MX1508 Mini Dual Channel 1.5A 1.5A 2 Way PWM Speed Controller Dual H-Bridge Replace Stepper

  • Motor drive module is ideal for use in battery-powered smart car, toy cars, robots..
  • Dual H-bridge motor driver, can drive two DC motors or a 4-wire two-phase stepper motor..
  • Supply voltage 2V -- 10V, can drive two DC motors or a 4-wire 2-phase stepper motors ,can achieve forward rotation or reverse rotation, it is possible to adjust the rotation speed..
  • Dual 1.5A * 2, the peak current to be 2.5A, built-in thermal protection circuit, do not be afraid motor stall burned, automatic recovery after the temperature dropped..
  • Use of imported original chip, built-in low on-resistance MOS switch, minimal heat, no heat sink, small size, low power consumption, is ideal for battery powered..
Check Stock

HiLetgo L298P DC Motor Drive Module L298P DC Motor Drive Shield H-Bridge Drive Expansion Board High-Power DC Stepper Motor Controller for Arduino

  • Driven part of the input voltage VS: VIN Input 6.5 ~ 12V, PWRIN 4.8 ~ 35V input..
  • The L298P shield DC motor driver has PWM speed control mode.
  • Adopt dedicated high-power motor driver chip L298P which can directly drive two DC motors with drive current up to 2A..
  • Stack design can be directly plugged into the Arduino, easier to use..
Check Stock

AOICRIE 4PCS L298N Motor Drive Controller Board Module Dual H Bridge DC Stepper for Arduino

  • L298N as Main driver chip L298N, strong driving ability, strong anti-interference, low calorific value, afterflow diode protection, more stable and reliable for Arduino projects, Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability..
  • Double H bridge design, can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors, high efficient, To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage..
  • Driving DC motor Because the module is drived by double H bridge,it can drive two motors simultaneously.Input the following driving timing from IN1-IN4 then the speed and direction of the stepper motor can be controlled..
  • Easy to Use No assembly required. This L298N board comes ready to go. Just wire up motors and power, easy to use..
  • Wide Usage Great for DIY Smart Car Robot Power MEGA R3 for Mega2560 Duemilanove, if driving voltage is more than 12V, use external standard 5volt TTL outputs to switch the H-bridge circuits..
Check Stock

20PCS Vibration Motor DC3V 12000rpm Mini Vibration Motor Vibrating Motor for Cell Phone Electronic Device Repair Single Board Computers Project Classroom Project Bristle Bots Cable 2in

  • 【20PCS Flat Vibration Motor】Voltage:DC 3V(Voltage Range2.7V~3.3V) Rated Speed:12000RPM Rated Current:90mA Size:φ10mm*3mm Cable Length: 2in 5cm.
  • 【Reinforced Vibration Motor】High-strength stainless steel body,High-quality Magnets，More powerful vibration,Longer service life,Thicker cable,Reinforced treatment at the weld point,Lead wires loose strength ≥ 1Kgf,Stronger temperature and humidity adaptation range,-4℉~158℉（-20℃~70℃）15%RH~90%RH.
  • 【Easy-to-use vibration motor】Available in 3cm 5cm 8cm cable length variants,Reinforced adhesive backing for more reliable self-adhesive performance,Pre-peeled cable, Longer exposed length, ready to use, no need to worry about manually peeling the cable will cause cable damage.
  • 【The use of Vibration Motor】Manufacture, repair and DIY of cell phones, tablets, wearables and other electronic devices.brush bots,bristle bots,Ninja Botand other classroom projects and cub scout project.vibration source and haptic feedback for Raspberry Pi,arduino,Single Board Computer and other projects that use vibration motors.
  • 【Warning for Vibrating Motor】Please use a suitable dc power supply. Use the proper voltage and current. The size of the parts is small, please do not allow young children to use alone..
Check Stock

52 Inch Minimalist Style DC Motor Ceiling Fan with LED Light, Reversible Motor and 3 ABS Blades, ETL Listed Indoor Ceiling Fans for Kitchen Bedroom Living Room, 6-Speed Remote Control

  • MINIMALIST STYLE: This 52-inch indoor ceiling fan has 3 powerful blades to make your home more comfortable.
  • their walnut finish attractively compliments any home decor from rustic industrial to minimalist.
  • REVERSIBLE FAN: It has 3 blades designed for high volume air movement and rotates in reversible direction for changing seasonal needs and has remote controlled operation..
  • REMOTE CONTROL: The convenient remote control allows you to adjust this fan's 6 speeds and 3 timer settings (1/4/8 hr.) from anywhere around your room, whether lying in bed, eating at the dining room table, or relaxing on your living room couch.
  • DC MOTOR: DC motor is energy efficient and ETL listed and has convenient wall holder for remote storage. These fans save on operating costs with energy efficient DC motors. They save up to 65% more efficient than traditional AC fan motors..
  • NOTICE: The DC motor can only work properly after the blades are installed (with load), so we recommend that you also install the blades during the installation test.
Check Stock

Ignition Coil Module, Pulse Generator High Voltage with Pulse Generator for Replacement for Electronic DIY for Product Development

  • It can be used as high voltage source for high school science experiment, electronic instrument, negative ion generator and little science..
  • After the input of dc 3.0V-6V voltage, a dc high voltage of about DC200KV(about 1.5 cm of arc) can be obtained at the output end..
  • According to the coil principle, the module outputs high voltage pulse current, small volume and high efficiency..
  • The peripheral circuit is simple (simply connect the switch, Install the battery), the discharge is violent..
  • Used for high voltage production, electronic DIY, product development, high voltage electronic security, etc.
Check Stock