Reviews Cylinder Valve Nut

GY6 Cylinder Rebuild Kits Trkimal 47mm 80cc Big Bore Upgrade Kits for 49cc 50cc 139QMB Engines 64mm Valve scooter moped parts, GY6 Engine parts for Chinese Scooter(64mm Valve Length)

  • 【Cylinder Bore】: 47mm / Non-EGR Cylinder.
  • 【Apply to】: GY6 4 stroke 49cc 50cc 60cc 80cc engine upgrade for most of chinese scooter, atv and go karts.
  • 【Parts included】:GY6 80cc Cylinder Head with 64mm valve, 47mm Bore Cylinder Block, Set of 47mm Piston Assy, Piston, Rings and Wrist Pin, Full Set of Engine Gasket, 6pins CDI, Ignition coil, 4pin AC regulator, relay, A7TC Spark Plug, Set of Intake Manifold and Muffler Bolts, and Exhaust locking ha, Set of 8.5 Gram roller , Rocker Arms, Valve Seals, Oil Pump Assy with Driving Gear, Camshaft, Camshaft chain 82, belt 699*18*30, Chain adjuster, Oil screen, spring, cover and oil seal, Starter clutch.
  • 【Fit to】Roketa, Sunl, Baja, Taotao, Panterra, Redcat Tank Giovanni Wildfire Xtreme Seaseng Qlink Yiben Jonway Jmstar, Vento.
Check Stock

LASCO 04-4104, 1-Pack

  • Adjustable 6-Inch-12-Inch, with refill tube and supply nut, no float needed.
Check Stock

Soda Stream CO2 Cartridges Refill Exchange Adapter Bottle Connector CO2 Tank Soda Maker Accessories with Hose for Filling Sodastream CGA320 Tank

  • The Soda Stream CO2 Cylinder Refill Adapter refill adapter can be used to refill small CO2 tanks from larger CO2 tank,the standard should be CGA320..
  • Please upside down your CO2 tank if you can not refill when the CO2 tank standing,because some of tank have not the dip tube (syphon tube)inside..
  • The cylinder should be empty.Pre Cooled cartridges will get quite full..
  • You should open the tank valve very slowly when you filling the protection valve(6mm wide pin) of sodastream bottle..
  • Our adapter don’t work RPV valve (residual pressure valve),but some of RPV valve can be removed by hex wrench,please check before ordering.
Check Stock

RP22734 Replacement Bonnet Nut Compatible with Delta R10000 Shower Valve

  • Compatible with Delta R10000 series shower valve.
  • Good build quality and come with solid, clean threads.
  • Must use a wire brush to clean-up the threads on the valve body & wipe off any grit before install bonnet nut. If clean, nut should turn easily and snug up without excessive force.
  • Recommend to replace bonnet when replacing cartridge so that you can assure seals are properly seated/compressed in the valve body.
Check Stock

Protech 63010 Refrigerant Recovery Cylinder, 400 psi, 50 lb.

  • Powder coated cylinder for high gloss, durable finish.
  • Reusable and conforms to dot-4ba400 specifications and ari guidelines.
  • 3/4" npt opening accepts 80 percent fill float switch shut-off device (does not included the float switch valve, if you need it, please see master cool part # 62011 which includes it).
  • Pre-charged cylinder provides a clean, dry interior.
Check Stock

Victor 0381-1932 CA 2462+ Cutting Attachment, 180° Head

  • Improved head durability, preheat control valve flow and reduced user fatigue due to improved balance.
  • Improved access and reparability of mixer with single nut removal.
  • Superior cutting oxygen valve with improved feathering/ease-on control.
  • No wrench flats on connection nut indicates hand tightening only for safer operation.
  • Internal connection snap ring prevents coupling nut sliding and exposure to o-rings for reduced damage.
Check Stock

Victor 0381-1928 CA 2460+ Cutting Attachment, 90° Head

  • Improved head durability, preheat control valve flow and reduced user fatigue due to improved balance.
  • Improved access and reparability of mixer with single nut removal.
  • Superior cutting oxygen valve with improved feathering/ease-on control.
  • No wrench flats on connection nut indicates hand tightening only for safer operation.
  • Internal connection snap ring prevents coupling nut sliding and exposure to o-rings for reduced damage.
Check Stock

RP64851 Replacement Bonnet Nut Compatible with Delta R11000 Shower Diverter Valve

  • Compatible with Delta R11000 shower diverter valve.
  • Good build quality and come with solid, clean threads.
  • Must use a wire brush to clean-up the threads on the valve body & wipe off any grit before install bonnet nut. If clean, nut should turn easily and snug up without excessive force.
  • Recommend to replace bonnet when replacing cartridge so that you can assure seals are properly seated/compressed in the valve body.
Check Stock

BBR Tuning Racing Series DIO Cylinder Body & High Performance 21mm OKO Carburetor Assembly

  • RACE READY PERFORMANCE: With the BBR Tuning Racing Series DIO Cylinder Body & Reed Assembly with OKO 21mm Carburetor w/ Velocity Stack you’ll get the power and speed your build’s been looking for. A ported cylinder body with a high performance reed valve intake system, this race assembly was made for race engines in mind..
  • PORTED CYLINDER: Unlike other cylinders, the BBR Tuning Racing Series DIO Cylinder Body is ported to allow maximum fuel and air mixing within your motor. The exhaust port can fit nearly any performance muffler as well as any stock exhaust muffler you want to run, which the intake port is specifically designed to accept the reed valve assembly included with this kit.
  • BOOSTS POWER: With a 32mm opening, you’ll be able to fit hardcore racing carburetors like the BBR Tuning High Performance 2-Stroke OKO Style Carburetor without a single problem. With the right carburetor, this reed will deliver tons of fuel and air to your motor and give you higher speeds and even more torque..
  • COMPLETE KIT: The BBR Tuning Racing Series DIO Cylinder Body & Reed Assembly is paired with a 21mm OKO Race carburetor is racer’s dream setup- get ready for a bike that’ll scream whenever you hit the gas!.
  • INCLUDES: Modified BBR Tuning Racing Series DIO Cyl....
Check Stock