Reviews Cooling Module

Plasma & LCD TV Vertical-Mount Cooling Fan System, with USB-Control & multispeed Fans

This cooling unit is designed to quietly pull hot air out of your TV or video monitor. It has 2 high-quality, low-noise 120mm fans, with long-lasting and quiet fluid dynamic bearings. Each fan has a mounting plate, with a rubber air-chamber ring around the bottom edge, to make sure the fan is sealed against the back of the TV. The fans are also fitted with snap-lock adhesive pads, which stick the fans to the back of your TV, yet allow easy removal and reinstallation..
The system includes a USB control module, which turns the fans on and off, under the control of your TV’s USB port (type A connector). The USB module controls the power from the multi-voltage transformer (included with the cooling system), which runs the fans. In addition, YOU control the fan speed, using the multi-speed fan controller..
IMPORTANT: Please make sure that your TV’s USB port turns on (powers up) ONLY when the TV is turned on. That way, the fans will run when the TV is on and turn off when the TV is off..
Recommended fan speeds for this system: The fans (running together at 2/3 speed) are rated at 19db while moving 98 cubic feet of air per minute, or 22db & 110CFM at 3/4 speed. With cabinet cooling, slow (and quiet) are the way to go! Other available speeds....

Applies for Small Area Cooling: This Peltier Module is suitable for small space cooling, semiconductor refrigeration learning theory, research solutions developed cooling equipment planning.
Working Principle: Air cooling device, not used to cool the water, use water to dissipate heat, and eventually the water is hot, not cold.
Easy to Operate: This kit is a finished product that does not need to be assembled, Simple operation, cooling quickly, outstanding performance.
Offers Stable Performance: Stable work and low noise, no vibration, no refrigerant required.
Working Range: Suitable for 20L space cooling, air temperature can be cooled to 5-8 degrees than normal.

Active cooling backplate：The newly developed and designed graphics card backplane water block covers the entire back of the PCB, which effectively....
Jet type micro channel structure:The 0.5MM gap has strong passability, even when using color powder or nano-silver water-cooling liquid, it is not....
T2 high-purity copper plate: The heat-absorbing plate of the water block is made of the national standard T2 high-purity purple plate, the base....
Suggested water way: The new bridge module is used for Unicom's graphics card water cooling head and backplane water cooling head. It is small in size....
Heat dissipation cooling water-cooled head backplate: The water-cooled head is equipped with an exclusive backplane of high-quality electroplated....

The Add-Ons Include: Expansion Board, Metal Case, Power Supply, And Cooling Fan. Easily Make A Mini-Computer If You Happen To Get A Compute Module.
Compute Module PoE Board: Dual CSI Camera Ports, PoE (Power Over Ethernet) Feature, Versatile Peripheral Interfaces.
Ingenious Cut-Out, Highly Matching The Master Board, Along With Clear Labels, Easy To Use.
Comes With Cooling Fan, Allows Being Controlled By Software Via GPIO, Or Being Powered Directly From 5V Supply.
Smooth And Clean Metal Bottom Surface, With Mounting Holes On Both Sides, Suitable For Industrial Applications.

A failing HVAC auxiliary fan control module can lead to engine overheating and costly damage.
URO's direct-fit OE replacement design instantly restores factory HVAC auxiliary fan control module function.
Alloy conductors minimize electrical resistance for accurate fan speeds and precise control of engine cooling.Designed and tested for reliability and long life.Manufactured using high-quality materials to withstand intense engine compartment heat.24-Month / Unlimited Mileage Warranty.Fit type: Vehicle Specific.

Control heating, cooling and IAQ equipment with only 2 wires at the thermostat. Heating, cooling and IAQ equipment wires to the Equipment Interface Module..
Smart Schedule - programs in seconds for any lifestyle.
Patented interview based programming and installer setup..

【All-in-one Liquid CPU Cooler Kit】This offers a 240 mm radiator, pump, cylindrical tank, dual fan, and mounting accessories that will greatly enhance the cooling experience, especially in terms of stability, mute, efficiency and convenience..
【CPU/GPU Module】The CPU/GPU module is built with a copper substrate that provides excellent heat transfer and cooling performance..
【Cylindrical Water Tank】The cylindrical water tank is made of high quality POM acrylic and the circulation system can be seen..
【Water Pump & 240mm Heatsink 】Water Pump: Waterproof, stable, high mute, long life. 240mm Heatsink: Provides excellent heat dissipation for highly overclocked desktop processors..
【Transparent Hose & LED Fan】Transparent Hose: Upgraded flexible explosion-proof hose saves space and provides excellent durability.LED Fan: Extreme Performance Dual fans provide high air static pressure and low noise..

...al raised air-chamber base, which covers 145 square inches, and air is drawn out over the entire area of this raised base..
The system includes a 12 volt trigger control module, which turns the fan on and off, under the control of your component’s 12v trigger socket. The 12v module controls the power from the cooling system’s multi-speed transformer, directing it to the fans when it detects a 12v signal. In addition, you control the speed of the fans, with the multi-speed power controller..
IMPORTANT: Some receivers have a non-standard setup, where the receiver doesn’t directly control the trigger (for example, the trigger might be under the control of Zones 2 or 3, etc.). Please consult your receiver’s manual for details about how its 12v trigger operates, or contact me if you have questions..
Recommended fan speeds for this system: The fans (running together) are rated at 13db while moving 50 cubic feet of air per minute at 1/3 speed, or 16db & 72CFM at 1/2 speed. With component cooling, slow (and quiet) are the way to go! Other available speeds: 2/3 speed = 19db/98CFM, 3/4 speed = 22db/110CFM, full speed = 25db/148CFM..
The Megabase cooling unit measures 14.5″ wide, and 10″ deep. It is 1-1/2″ tal....

✔Geekworm design 12mm aluminum alloy heatsink for Raspberry Pi Compute Module 4 CM4.
User manual, refer to Geekworm WiKi search C235..
✔Heatsink dimensions: 54x39x12mm/2.12x1.53x0.47inch.
✔Support install 30mm (3007 or 3010) cooling fan above the heatsink for better heat dissaption.
✔With one piece thermal pad, need to cut proper thermal pad to attach on the CPU of Raspberry Pi Compute Module 4.
✔The C235 heatsink reserve the space to connect the extermal antenna for CM4. ✔The inclcuded PM2.5x16mm screws length is just for install CM4 module and C235 heatsink, no support CM4 IO board..