Reviews Chuck Arbor

Metal Lathe Drill Chuck Fits - Grizzly G8688 Metal Lathe - 1/2 Inch Heavy Duty Drill Chuck - Replacement Drill Chuck - Made in the USA

  • LIFETIME ASSURANCE : All our accessories for sanders, planers, sharpeners, band saws, compressors, drills, including bearings, guide bearings, thrust bearings, drill chucks, drive belts, arbors and band saw tires are backed by top-notch service and EVERLASTING commitment..
  • MADE IN THE USA : Every single drill chuck and arbor is EXCLUSIVELY designed and produced in the USA in line with the highest quality standards. Choose our smooth bearing replacement for dependable performance..
  • WIDE COMPATIBILITY : DNLK drill chucks and arbors are compatible with most brands. Order our heavy duty drill chucks and profit from reduced downtime and maintenance..
  • SUPREME DURABILITY, WEAR RESISTANCE : In addition to a tight fit and flawless operation, our drill chucks and arbors have been tested and have proven to withstand high shocks and heavy-duty loads in both cold and hot environments..
  • DNLK drill chuck will fit Grizzly G8688 Metal Lathe.
Check Stock

Grizzly Industrial G0709-14 x 40 Gunsmithing Gearhead Lathe

  • 2 MT#3 dead centers (1 carbide tipped) 1 MT#3 live center 1 MT#5 - MT#3 sleeve 1/2" drill chuck w/ MT#3 arbor.
  • Dimensions 51-3/4"H, 71-3/4"L, 30"W Approximate shipping weight 1550lbs 11" face plate.
  • Motor 2 HP, 110/220V, single-phase, 20/10 Amps, 60Hz, 1725RPM Number of speeds 8 Range of speeds 70-2000RPM.
  • Spindle bore 1-9/16" Spindle nose taper MT#5 Spindle nose D1-5 Camlock D1-5 spindle nose (6 pin) 1-9/16" spindle bore.
  • Swing over bed 14" Swing over gap 19-3/4" Swing over cross slide 8-3/4".
Check Stock

HLOFIZI 2-1/2 Inch Carbide Grit Hole Saw Diameter 2.5\ Cutting Through Stucco, Brick, Plaster, Cement Board, Drywall, Hardie Board, Hardwood, PVC with 1-1/2\ Depth, Up to 6X Faster

  • 2.5” hole saw constructed with long-lasting tungsten carbide grit edge, easy and fast cuts thick wood, plaster stucco ceiling & wall. Cutting depth 1-1/2 inch.
  • Drilling holes through lots of abrasive materials, stucco, old plaster, drywall, hard wood, plywood, sheetrock, cement board, plastic, PVC.
  • Clean and smooth cutting, slot for easy plug removal. Comes with arbor and carbide-tipped pilot drills. Arbor: 7/16" shank, fit 1/2" chuck.
  • Not recommended for cutting metal sheet, concrete block, cement tile.
  • 100% SATISFACTION GURANTEED: If you are dissatisfied with our 2-1/2” carbide hole saw for any reason, return your order within 90-Days for full refund, we will always go above and beyond to ensure you are happy with your customer experience. We appreciate all your remarks and comments. They are the key tools to develop and improve our hole saw.
Check Stock

A-Line It Basic Kit with Dial Indicator For Aligning and Calibrating Work Shop Machinery Like Table Saws, Band Saws and Drill Presses

  • Quickly set-up, tune up, and check the accuracy of your shop's tools with this system. Check table saw blade and fence alignment, arbor and blade run-out, miter slot to blade squareness, arbor/chuck run-out, jointer/planer head to table parallelism, jointer/planer knife alignment, out-feed table alignment.
  • router/shaper spindle run-out, or any other set up or alignment measurement you desire..
  • The A-LINE-IT Basic Kit is the perfect starter kit for hobbyists and small shops..
  • The 1" capacity dial indicator reads in .001" increments for absolute precision. Self adjusting miter groove bar with leveling screws and spring plungers for perfect fit in your miter slot..
  • Dial indicator mounting bar measures 3/4” x 3/4” x 5-1/2”, miter groove bar measures 3/8” x 3/4" x 6-1/4"..
  • Comes with hardware and hex wrench for assembly, instructions and instructional DVD for expert guidance in getting the best performance and accuracy from your woodworking machines..
Check Stock

HLOFIZI 6 Inch Hole Saw Tungsten Carbide Tipped for Recessed Lights, Drilling Metal, Hardwood, Nail-Embedded Wood, Stucco and Wire Mesh Combination, Plaster, Cement Fiber Board

  • Tungsten carbide tipped teeth for extended cutting life, drilling clean holes, more efficiently. Up 10X longer life that 6” bi-metal hole saw.
  • Drills clean wood, wood with nails, hardy board, aluminum, metal, cast iron, stainless steel sheet, cement fiber board, sheetrock, plastic, fiberglass. Also Ideal for recessed lights.
  • Carbide tooth makes cutting holes through stucco/plaster and wire mesh combination, wood and metal combination, faster and easier with less effort.
  • Clean and smooth cutting, slot for easy plug removal. Comes with arbor and carbide-tipped pilot drills. Arbor: fit 3/8" chuck.
  • 100% SATISFACTION GURANTEED: If you are dissatisfied with our 6 in. carbide tipped hole saw for any reason, return your order within 90-Days for full refund, we will always go above and beyond to ensure you are happy with your customer experience. We appreciate all your remarks and comments. They are the key tools to develop and improve our hole saw.
Check Stock

Chuck Holder, Milling Tool Holder Not Rusty for Processing Steel and Cast Iron

  • Furthermore, this milling arbor adapter is suitable for processing steel and cast iron, soft stainless steel and aluminum..
  • Easy to use and not rusty, such chuck holder is easy to use in the practical life..
  • With good chemical stability, heat resistance and abrasion resistance, the holder is in high hardness..
  • After many inspections before leaving the factory, the quality is guaranteed, you can use it with confidence..
  • Made of high-quality hard alloy cutter head, the milling tool holder is with exquisite workmanship and durable..
Check Stock

HLOFIZI 1-3/8 Inch Hole Saw (35 MM) with Tungsten Carbide Tipped for Drilling Metal, Hardwood, Nail-Embedded Wood, Stainless Steel, Stucco and Wire Mesh Combination, Plaster, Cement Fiber Board

  • Tungsten carbide tipped teeth for extended cutting life, drilling clean holes, more efficiently. Up 10X longer life that 1-3/8” bi-metal hole saw.
  • Drills clean wood, wood with nails, hardy board, aluminum, metal, cast iron, stainless steel sheet, cement fiber board, sheetrock, plastic, fiberglass and more.
  • Carbide tooth makes cutting holes through stucco/plaster and wire mesh combination, wood and metal combination, faster and easier with less effort.
  • Clean and smooth cutting, slot for easy plug removal. Comes with arbor and carbide-tipped pilot drills. Arbor: fit 3/8" chuck.
  • 100% SATISFACTION GURANTEED: If you are dissatisfied with our 1-3/8 in. carbide tipped hole saw for any reason, return your order within 90-Days for full refund, we will always go above and beyond to ensure you are happy with your customer experience. We appreciate all your remarks and comments. They are the key tools to develop and improve our hole saw.
Check Stock

HLOFIZI 4 Inch Carbide Grit Hole Saw for Recessed Lights and Dryer Vent, Cuts Through Stucco, Ceiling Old Plaster, Drywall, Cement Board, Hard Wood with 1-1/2\ Depth, Up to 6X Faster

  • 4 inch hole saw ideal for installing recessed lighting, dryer vent hole, and other roof vent.
  • Drilling holes through lots of abrasive materials, ceiling stucco, old plaster, drywall, hard wood, plywood, sheetrock, cement board, plastic, PVC. Not recommended for cutting metal sheet, brick, concrete block, cement tile.
  • Constructed with long-lasting tungsten carbide grit edge, 4 in. hole saw easy and fast cuts thick wood, plaster stucco ceiling & wall. Cutting depth 1-1/2 inch.
  • Clean and smooth cutting, slot for easy plug removal. Comes with arbor and carbide-tipped pilot drills. Hole saw arbor: fit 3/8" chuck.
  • 100% SATISFACTION GURANTEED: If you are dissatisfied with our 4" carbide hole saw for any reason, return your order within 90-Days for full refund, we will always go above and beyond to ensure you are happy with your customer experience. We appreciate all your remarks and comments. They are the key tools to develop and improve our hole saw.
Check Stock

HQRP On-Off Toggle Switch compatible with Delta 489105-00 11-900 11-950 11-980 11-985 11-990 14-040 17-900 DP400 DP300L 17-950L Drill Press, 34-670 36-600 36-977 36-978 36-980 36-981 TS200LS Table Saw

  • LIFETIME ASSURANCE : All our accessories for sanders, planers, sharpeners, band saws, compressors, drills, including bearings, guide bearings, thrust bearings, drill chucks, drive belts, arbors and band saw tires are backed by top-notch service and EVERLASTING commitment..
  • MADE IN THE USA : Every single drill chuck and arbor is EXCLUSIVELY designed and produced in the USA in line with the highest quality standards. Choose our smooth bearing replacement for dependable performance..
  • WIDE COMPATIBILITY : DNLK drill chucks and arbors are compatible with most brands. Order our heavy duty drill chucks and profit from reduced downtime and maintenance..
  • SUPREME DURABILITY, WEAR RESISTANCE : In addition to a tight fit and flawless operation, our drill chucks and arbors have been tested and have proven to withstand high shocks and heavy-duty loads in both cold and hot environments..
  • DNLK drill chuck will fit Delta Model 11-990 Type 2.
Check Stock