Reviews Bevel Gear Spline

EXAUTOPONE Stainless Steel Bevel Gear Set AR44 Compatible with AR44 Heavy Duty RC Car Bevel Gear Set 30T/8T

  • 32 teeth for use with L149Y-P mating bevel gear in 2:1 gear ratio applications.
  • Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
  • Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
  • Low carbon steel (0.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
  • Unhardened teeth for applications where hardness and strength are not needed to transmit torque and motion.
Check Stock

1PC 90-Degree reversing Angle Gear Right Angle Gear Steering Small Bevel Gear Box Bevel Gear Speed Ratio 1:1 (A)

  • 16 teeth for use with PA4416Y-G mating bevel gear in 4:1 gear ratio applications.
  • Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
  • Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
  • Low carbon steel (0.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
  • Unhardened teeth for applications where hardness and strength are not needed to transmit torque and motion.
Check Stock

Boston Gear L153Y-G Bevel Gear, 1.5:1 Ratio, 0.750\ Bore, 10 Pitch, 30 Teeth, 20 Degree Pressure Angle, Straight Bevel, Steel

  • 30 teeth for use with L153Y-P mating bevel gear in 1.5:1 gear ratio applications.
  • Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
  • Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
  • Low carbon steel (0.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
  • Unhardened teeth for applications where hardness and strength are not needed to transmit torque and motion.
Check Stock

Boston Gear L147Y-P Bevel Pinion Gear, 2:1 Ratio, 0.188\ Bore, 20 Pitch, 10 Teeth, 20 Degree Pressure Angle, Straight Bevel, Steel

  • 10 teeth for use with L147Y-G mating bevel gear in 2:1 gear ratio applications.
  • Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
  • Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
  • Low carbon steel (0.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
  • Unhardened teeth for applications where hardness and strength are not needed to transmit torque and motion.
Check Stock

DEWALT ATOMIC 20V MAX* Circular Saw, 4-1/2-Inch, Tool Only (DCS571B)

  • Brushless motor of DEWALT circular saw allows you to cut up to 369 linear feet of 3/4-inch OSB using DCB205 battery (sold separately).
  • The cordless circular saw has the removable auxiliary handle for increased control.
  • The compact circular saw has a hang hook for increased convenience.
  • On-board blade key storage for hassle free blade changes.
  • 1-1/2-inch finger trigger allows users to choke-up on tool if necessary for their application.
  • Bevel gear allows users to cut 2x material at 90 degrees with a 4-1/2-inch blade.
  • Electronic blade brake stops blade quickly for safety and productivity.
  • Bevel lever gives user the ability to bevel at 45 degrees to cut 1x dimensional lumber.
Check Stock

USA Standard Gear ZIKD44-S-30-JK Open Spider Gear Set for Dana Spicer 44 JK Non-Rubicon Rear, 30 Spline

  • For Dana Spicer 44 JK non-Rubicon rear differential.
Check Stock

USA Standard Gear (ZG D30S-456TJ) Replacement Ring & Pinion Gear Set for Jeep TJ Dana 30 Short Pinion Differential

  • Fits standard rotation Dana Spicer 30 with short pinion.
Check Stock

PGFUN 2 Pcs 1M 20 Teeth 5/6/8mm Shaft Hole Tapered Bevel Gear 1:1# 45 Steel 1 Module 90 Degree Steering Gear with M5 Fixing Hole (5 mm)

  • 18 teeth for use with L152BY-G mating bevel gear in 2:1 gear ratio applications.
  • Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
  • Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
  • Low carbon steel (0.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
  • Unhardened teeth for applications where hardness and strength are not needed to transmit torque and motion.
Check Stock

Makita GS5000 5\ Straight Grinder

  • Rubberized handle for increased operator comfort.
  • “Tool-less” guard cap removal for more convenient wheel changes.
  • Spiral bevel gears for smoother rotations and a more efficient transfer of energy.
  • Externally accessible brushes for easier serviceability.
  • Zig-zag varnish protects the armature coil by deflecting dust and debris for longer motor life.
  • Rubberized handle and gear housing for increased operator comfort and control.
  • "Tool-less" guard cap removal for quick wheel changes.
Check Stock