Reviews Bevel Gear Set

DEWALT ATOMIC 20V MAX* Circular Saw, 4-1/2-Inch, Tool Only (DCS571B)

  • Brushless motor of DEWALT circular saw allows you to cut up to 369 linear feet of 3/4-inch OSB using DCB205 battery (sold separately).
  • The cordless circular saw has the removable auxiliary handle for increased control.
  • The compact circular saw has a hang hook for increased convenience.
  • On-board blade key storage for hassle free blade changes.
  • 1-1/2-inch finger trigger allows users to choke-up on tool if necessary for their application.
  • Bevel gear allows users to cut 2x material at 90 degrees with a 4-1/2-inch blade.
  • Electronic blade brake stops blade quickly for safety and productivity.
  • Bevel lever gives user the ability to bevel at 45 degrees to cut 1x dimensional lumber.
Check Stock

Bang II (Feat. Uppercase 5ive)

  • Fully milled gearbox housing made of 6061-T6 aluminum for the rear axle of ATOPRC.
  • Due to its dimensional stability results in a higher load capacity and service life of bevel gear and ball bearings. The problem of the torn fastening thread has an end with this case.
  • The bearing adapters are included in the set.
  • We recommend gluing the bearings with threadlocker y0113. For mounting the bearing adapters in the housing we recommend Bindulin silicone y19015. To use HD differential shafts y1477, the Atoprc bearing adapters must be machined.
Check Stock

PGFUN 2 Pcs 1M 20 Teeth 5/6/8mm Shaft Hole Tapered Bevel Gear 1:1# 45 Steel 1 Module 90 Degree Steering Gear with M5 Fixing Hole (5 mm)

  • 18 teeth for use with L152BY-G mating bevel gear in 2:1 gear ratio applications.
  • Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
  • Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
  • Low carbon steel (0.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
  • Unhardened teeth for applications where hardness and strength are not needed to transmit torque and motion.
Check Stock

Makita GS5000 5\ Straight Grinder

  • Rubberized handle for increased operator comfort.
  • “Tool-less” guard cap removal for more convenient wheel changes.
  • Spiral bevel gears for smoother rotations and a more efficient transfer of energy.
  • Externally accessible brushes for easier serviceability.
  • Zig-zag varnish protects the armature coil by deflecting dust and debris for longer motor life.
  • Rubberized handle and gear housing for increased operator comfort and control.
  • "Tool-less" guard cap removal for quick wheel changes.
Check Stock

Husqvarna 525L Pro String Trimmer 966781701 25.4cc 1.21 HP

  • Hard chromium plated cylinder bore provides increased durability and extended product life.
  • Bevel gear designed with high torque and the cutting equipment parallel to the ground for best cutting performance.
  • Stop switch automatically resets to the ON position for easier starting.
  • Heavy duty twin line cutting system with Tap 'n Go for quick line feed.
  • Starting a cold engine is easier with the intuitive choke which is easy to reach and set.
  • Air purge removes air from carburetor and fuel system for easy starting.
Check Stock

SKILSAW SPT78W-01 15-Amp 8-1/4-Inch Aluminum Worm Drive Circular Saw

  • High torque 15 Amp Dual-Field motor designed specifically for relentless power.
  • 60° bevel allows users to complete a wider variety of cuts with bevel stops at 0° and 45°.
  • The anti-snag lower guard provides smooth operation for small cut-off pieces.
  • Precision-machined, durable worm drive gears for longer tool life.
  • Die-cast aluminum motor and gear housings for durability.
Check Stock

Boston Gear HL148Y-P Bevel Pinion Gear, 2:1 Ratio, 0.375\ Bore, 16 Pitch, 12 Teeth, 20 Degree Pressure Angle, Straight Bevel, Keyway, Steel with Case-Hardened Teeth

  • 12 teeth for use with HL148Y-G mating bevel gear in 2:1 gear ratio applications.
  • Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
  • Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
  • Low carbon steel (0.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
  • Case-hardened teeth for applications where hardness and strength are needed to transmit torque and motion.
Check Stock

Lesco 101186 High Wheel Walk-Behind Fertilizer Spreader with Gearbox Repair Kit (Bundle, 2 Items)

  • Bundle includes 2 Items: (1) Lesco 101186 High Wheel Walk-Behind Spreader with (1) Gearbox Repair Kit.
  • Lesco Gear Repair Kit includes 1 x Seal (# 030384), 1 x Gear Cap (# 030593), 1 x Bevel Gear (# 030594), 1 x Pinion Gear (# 030595), 1 x Roll Pin (# 060019), 1 x Roll Pin (# 060022), 2 x Seals (# 030385).
Check Stock

OSOYOO Omnidirectional Mecanum Wheels Robotic Car Kit for Arduino Coding Students Based on Mega2560 Introduction

  • 【Precision die casting】The bevel gears are made of zinc alloy material by accuracy die casting.
  • 【Strong compatibility】The product can compatible with for FRC and other world robot competitions.
  • 【Good quality and durable】High wear resistance, high strength and high rigidity.
  • 【Easy to replace】Including 2 sets of bevel gear and bearings, convenient to replace.
  • 【Exquisite and reasonable】Fine processing and reasonable design, good accessories for industrial robots.
Check Stock