Reviews Bearing Point

Titan Attachments Notched Disc Harrow 5 ft. 3 Point Category 1

  • ...pter, hook into the top link bar, and connect your lower lift pins..
  • DURABLE CONSTRUCTION: The 60-inch Disc Harrow is constructed using 2.5 x 2.5-inch steel tubing that is powder-coated to prevent rust and corrosion. The 16-inch notched discs are made from hardened steel. The 4-disc axles are equipped with cast iron bearing caps and spools that are greaseable..
  • DIMENSIONS: The overall dimensions of the Cat 1, 3 Point 5 FT Disc Harrow are 60-inches wide x 45-inches deep x 30.5-inches high. The notched discs are 16-inches in diameter and spaced 7.5-inches apart. The lower lift pins on the 3 Point hitch are 3.5-inches long and measure 28-inches apart, center to center..
Check Stock

Stainless Steel Lath Screws 8 x 3/4 Sharp Point Modified Truss Head Phillips Drive Quantity 1000 Type 17 Cutting Point 305 18-8 Stainless Steel Length 3/4 0.75 in.

  • Wire-Lath Modified Truss Head Screws for Fastening metal lath to wood. IDEAL for ALL applications where a larger bearing surface is needed underneath the head. HEAD DIAMETER is 0.42 Inches. #2 Phillips Drive.
  • ATTACHES WOOD OR LIGHT GAUGE METAL - Superior penetration through a variety of woods and thin metals.
  • REDUCES WOOD SPLITTING - ELIMATES NEED FOR PRE-DRILLING - This thread cutting screw is ideal for use with wood.
  • it offers a coarse tapping screw thread as well as a special long sharp point that is fluted in order to capture chips. The patented thread design and Type 17 point make drilling faster, reduce splitting, and allow these screws to be driven into most hardwoods without pre-drilling ..
  • HIGH DEGREE CORROSION RESISTANCE: Passivated and Waxed Stainless Steel Type 305 (18-8). HIGH QUALITY STAINLESS STEEL: These #8 Wood Screws are high quality grade 18-8 Stainless Steel, giving the screws one of the highest forms of corrosion resistance and strength, making it last longer than other hardware on the market today. For use in Non-Magnetic environments.
  • MODIFIED TRUSS HEAD - The rounded head top is much lower and flatter while the width of the head is wider, than pan or round screws of the same nominal size. The modified truss is basically a tru....
Check Stock

Stainless Steel Lath Screws, 8 x 1-5/8, Sharp Point Modified Truss Head Phillips Drive (Quantity: 100) Type 17 Cutting Point 305 (18-8) Stainless Steel, Length: 1-5/8 (1.625) in.

  • Wire-Lath Modified Truss Head Screws for Fastening metal lath to wood. IDEAL for ALL applications where a larger bearing surface is needed underneath the head. HEAD DIAMETER is 0.42 Inches. #2 Phillips Drive.
  • ATTACHES WOOD OR LIGHT GAUGE METAL - Superior penetration through a variety of woods and thin metals.
  • REDUCES WOOD SPLITTING - ELIMATES NEED FOR PRE-DRILLING - This thread cutting screw is ideal for use with wood.
  • it offers a coarse tapping screw thread as well as a special long sharp point that is fluted in order to capture chips. The patented thread design and Type 17 point make drilling faster, reduce splitting, and allow these screws to be driven into most hardwoods without pre-drilling ..
  • HIGH DEGREE CORROSION RESISTANCE: Passivated and Waxed Stainless Steel Type 305 (18-8). HIGH QUALITY STAINLESS STEEL: These #8 Wood Screws are high quality grade 18-8 Stainless Steel, giving the screws one of the highest forms of corrosion resistance and strength, making it last longer than other hardware on the market today. For use in Non-Magnetic environments.
  • MODIFIED TRUSS HEAD - The rounded head top is much lower and flatter while the width of the head is wider, than pan or round screws of the same nominal size. The modified truss is basically a tru....
Check Stock

Stainless Steel Lath Screws 8 x 1-1/4 Sharp Point Modified Truss Head Phillips Drive Quantity 1000 Type 17 Cutting Point 305 18-8 Stainless Steel Length 1-1/4 1.25 in.

  • Wire-Lath Modified Truss Head Screws for Fastening metal lath to wood. IDEAL for ALL applications where a larger bearing surface is needed underneath the head. HEAD DIAMETER is 0.42 Inches. #2 Phillips Drive.
  • ATTACHES WOOD OR LIGHT GAUGE METAL - Superior penetration through a variety of woods and thin metals.
  • REDUCES WOOD SPLITTING - ELIMATES NEED FOR PRE-DRILLING - This thread cutting screw is ideal for use with wood.
  • it offers a coarse tapping screw thread as well as a special long sharp point that is fluted in order to capture chips. The patented thread design and Type 17 point make drilling faster, reduce splitting, and allow these screws to be driven into most hardwoods without pre-drilling ..
  • HIGH DEGREE CORROSION RESISTANCE: Passivated and Waxed Stainless Steel Type 305 (18-8). HIGH QUALITY STAINLESS STEEL: These #8 Wood Screws are high quality grade 18-8 Stainless Steel, giving the screws one of the highest forms of corrosion resistance and strength, making it last longer than other hardware on the market today. For use in Non-Magnetic environments.
  • MODIFIED TRUSS HEAD - The rounded head top is much lower and flatter while the width of the head is wider, than pan or round screws of the same nominal size. The modified truss is basically a tru....
Check Stock

Orion Motor Tech Rear Axle Bearing Puller Tool Kit and Slide Hammer Set | Axle Seal and Bearing Remover Set with Slide Hammer Yoke and 3 Rear Axle Puller Adapters, 1\ to 2-7/8\ IDs

  • 8PC. SLIDE HAMMER SET: This 8-piece professional axle, bearing, and seal removal tool set by Orion Motor Tech provides a 5/8" slide hammer, yoke, locknut, hook, and adapters to let you quickly, easily, and safely repair rear axle problems on the vast majority of domestic cars and light trucks.
  • AXLE PULLER SET: Lock the slide hammer onto the 4-point yoke to set up a flange type axle puller that will let you extract parts with threaded holes, including stud axles, spur gears, and more.
  • SEAL PULLER SET: The 5.5 pound slide hammer and its sturdy T handle provide the firm grip and torque needed to pop out worn and damaged seals and other press fit parts using the included hook.
  • BEARING PULLER SET: The small, medium, and large bearing puller adapters cover inner diameters from 1 to 1-7/8.
Check Stock

Titan Attachments 4 FT Notched Disc Harrow Plow, Category 1, 3 Point, for Kubota New Holland Tractors

  • DURABLE CONSTRUCTION: The 48-inch Disc Harrow is constructed using 2.5 x 2.5-inch steel tubing that is powder-coated to prevent rust and corrosion. The 16-inch notched discs are made from hardened steel. The 4-disc axles are equipped with cast iron bearing caps and spools that are greaseable..
  • DIMENSIONS: The overall dimensions of the Cat 1, 3 Point 4 FT Disc Harrow are 48-inches wide x 45-inches deep x 30.5-inches high. The notched discs are 16-inches in diameter and spaced 7.5-inches apart. The lower lift pins on the 3 Point hitch are 3.5-inches long and measure 28-inches apart, center to center..
Check Stock

Titan Attachments 6 FT Notched Disc Harrow Plow, Category 1, 3 Point, for Kubota New Holland Tractors

  • DURABLE CONSTRUCTION: The 72-inch Disc Harrow is constructed using 2.5 x 2.5-inch steel tubing that is powder-coated to prevent rust and corrosion. The 16-inch notched discs are made from hardened steel. The 4-disc axles are equipped with cast iron bearing caps and spools that are greaseable..
  • DIMENSIONS: The overall dimensions of the Cat 1, 3 Point 4 FT Disc Harrow are 72-inches wide x 45-inches deep x 30.5-inches high. The notched discs are 16-inches in diameter and spaced 7.5-inches apart. The lower lift pins on the 3 Point hitch are 3.5-inches long and measure 28-inches apart, center to center..
Check Stock

WFLNHB Live Center 2MT 60 Degree Lathe Medium Duty Live Tailstock Center for Wood & Metal Lathe CNC Work

  • Specification: #2 Morse Taper (2MT) shank, 60-degree point, 5000 Max RPM, 600 lbs max workpiece weight, runout of 0.0004in/0.01mm T.I.R..
  • Material: The live revolving center is made of precision ground hardened steel, hardened to 61-65HRC, with high rigidity and wears resistance.
  • Triple Bearing Design: The 2MT activity center adopts a combination of a thrust ball bearing and two ball bearings for stable and smooth rotation.
  • Seal Ring: There is a seal ring at the front gland to prevent the entry of cutting fluid and dust.
  • Application: The live center MT2 is specially designed for lathes under medium-speed and medium-load environments. It can be used for high-speed turning and is suitable for CNC lathes.
Check Stock

PSI LCENTLT2 No. 2MT Heavy Duty Live Tailstock Center

  • Huge live center for heavy duty workpieces.
  • Cone is 2-1/2" by 1-11/16" overall diameter.
Check Stock