Reviews Axle Shaft Bushing Tool

Martin 2012 1 1/8 Taper Bushing, Sintered Steel, Inch, 1.13\ Bore, 2.75\ OD, 1.25\ Length

Taper bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
Sintered steel for greater strength and resistance to wear than steel.
Keyed to the shaft to prevent the shaft from rotating in the bushing.
Interchangeable with taper bushings from various manufacturers.

Useful CV Axle Puller: To replace or repair the CV axle joints easily, use this slide hammer kit. The CV joint puller adapter and large slide hammer bearing puller allow to create added torque to loosen and remove stubborn axle shafts and water pumps, without damaging to transmission cases or other components.
Efficient Front Wheel Drive Axle Puller Set: Efficient & Heavy-Duty: Our 10.5 lb curved slide hammers are heavier and larger, and the length of 19.5 inches ensures sufficient length slide to generate more force(so the generated pulling force is also twice than normal 5lb slide hammer). Save efforts and works more efficiently.
Combination Kit Fits All Needs: The CV axle joint pulley removal tool includes a T-style slide hammers, a steel wire joint puller, 2pc 16mm nuts, opening 63mm and 48mm CV joint fork removing attachments. All you need to remove CV axle or half shaft are put in this easy-carrying plastic case.
Superior Material: Heat-treated FWD axle puller adapter with black oxide finish is durable and resists rust and corrosion. Slide hammer and the VC join fork is made of high quality heavy steel materials w....

The ROP Shop replacement Shaft Kit for Drift Trike Bikes includes 36 Inch Tubular Aluminum Shaft, Axle.
Specs - Shaft Size: 36". Chain Type: #420. Wheel Size: 11 x 6.00 x 5. Maximum Weight Limit: 330 lbs. Refer to images 2 & 3 for more information.
Includes - (1) 36" Tubular Aluminum Shaft Axle, (2) Racing Slick Tires with Aluminum Wheels (11x6.00-5), (1) Sprocket (54T), (1) Sprocket Hub Adapter Plate, (1) Chain (#420), (2) Bearing Hangers, (4) Bearing Flangettes, (2) Aluminum Race Hubs with 1 1/4" Bore, (1) Clutch with 3/4" Bore (10T, #420), (2) Axle Bearings, (4) Lock Collars, (3) Key Stocks, (6) Axle Nuts, (6) Bolts, (6) Nuts & (2) Snap Rings.
This kit is used for many Drift Trike Bikes.
Please be sure to check your part or model number to ensure this is the correct shaft axle wheel kit for your unit. Also, please note this may replace multiple part numbers.

Lightweight,3/8 axle x 26T , Fit 3/8 inch axles..
High quality,Made of high-strength aluminum alloy material, strongly-built and heavy weight-bearing..
Bicycle Pegs,Compact bicycle foot pegs Knurled pegs, anti-skid.suitable for front and rear axles. Convenient tool for picking up another person by bicycle..
Easy to use,Mounted on the rear axle of the bicycle,Install the shaft screws to leak at least 6mm,Or directly remove the shaft nut the longer the screw leaks , the safer theinstallation and use..
Suit for universal Bike,road bike, mountain bikes, MTB, BMX, etc..

... x 1.5, M20 x 1.25, M20 x 1.50, 13/16" x 20UNEF, 3/4" x 20UNEF, and widely applicable, suitable for most vehicles..
【Can Be Used With 1-1/4" Socket Or Wrench & High-Strength/Durable High-Quality Steel Material】Thread restorer mechanic tool sets can be used with 1-1/4" socket or wrench to help better repair/clean shaft threads ,save time and energy. Made of high-quality steel, with high strength and durability, it can provide long-term service and reduce the cost of frequent tool replacement.(package does not contain 1-1/4" socket or wrench. ).
【Easy To Carry/Store】Thread restorer kit is packed in a high-quality plastic box, you can easily take it anywhere, and it is easy to store, and it can be neatly placed in the box after each use, so you don’t worry about losing.Convenient and easy to use..
【Note】This tool can be used with a 1-1/4" socket or wrench, but the package does not include a 1-1/4" socket or wrench..

EASY TO USE: Slide flat end of puller through center of bearing and flat against backside of bearing, then slide washer down the center of the shaft against front side of bearing and tighten the nut on smaller end of puller, then thread a slide hammer (not included) to the puller and slide hammer back and forth until the bearing comes out.
The washer captures the bearing firmly to distribute the applied force over the entire bearing and prevent damage.
Use the VCT Pneumatic SAE Standard Rear Axle Bearing Puller 3-Piece Service Set – Domestic Car Vehicle Bearings Removal Tool Kit to service semi-floating rear axle bearings on your vehicle.
These tools make the job simple and prevent damage to your bearings when pulling.
Much easier than claw-type axle bearing pullers that slip off and chew up the old bearings.
For removal only, not intended for installation.
FITS YOUR CAR: Standard SAE sizes work for most American domestic makes and models.
Set includes the following sizes to fit main bearing tube – 1 inch to 1-7/8 inches, 1-5/16 inches to 2-3/8 inches, and 1-3/8 inches to 2-7/8 inches.
Sizes permanently laser-etched on tool for easy identification.
Each tool fits a basic slide hammer with a 5/8-inch x 18 thread pitch.

Taper lock bushing with a torque capacity of 1,200 in-lbs for mounting a pulley, sheave, or sprocket on a drive shaft.
Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
Cast iron for resistance to wear, galling, and corrosion.
Keyed to the shaft to prevent the shaft from rotating in the bushing.
Interchangeable with taper lock bushings from various manufacturers.

Taper lock bushing with a torque capacity of 1,200 in-lbs for mounting a pulley, sheave, or sprocket on a drive shaft.
Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
Cast iron for resistance to wear, galling, and corrosion.
Keyed to the shaft to prevent the shaft from rotating in the bushing.
Interchangeable with taper lock bushings from various manufacturers.

Taper lock bushing with a torque capacity of 1,200 in-lbs for mounting a pulley, sheave, or sprocket on a drive shaft.
Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
Cast iron for resistance to wear, galling, and corrosion.
Keyed to the shaft to prevent the shaft from rotating in the bushing.
Interchangeable with taper lock bushings from various manufacturers.