Reviews Asychronous 3 Phase

Single Phase to 3 Phase Converter My-PS-7.5 Model Suitable for 5HP 3.7Kw 15 Amp 200-240V 3 Phase Motor DPS Must Be Used for One Motor Only Input/Output 200V-240V Digital Type

☞ Model: MDQ-100A is designed for single phase Full wave rectification, which has four diodes connected in a one phase bridge configuration..
☞ Max. Average Forward Rectified Current : 100A.
Production Size: 80 x 40 x 32mm/ 3.1" x 1.6" x 1.2" (L*W*T).
package content: 1 x rectifier bridge 1 net weight: 130g.
package content: 1 x rectifier bridge radiator.
☞ Applications: DC power supply for instrument equipment , Input of PWM frequence converter rectifying power supply , Excitation power supply for DC motor, Input of switch power supply and auxiliary current Inverter current..

This Bridge Rectifier Warranty 1 years . If there are quality problems within 8 years, you can send us email. We will send you new ones ..
Model: MDQ-100A is designed for single phase Full wave rectification, which has four diodes connected in a one phase bridge configuration..
Max. Average Forward Rectified Current : 100A.
Production Size: 80 x 40 x 32mm/ 3.1" x 1.6" x 1.2" (L*W*T).

Weight: 7.05 ib. The spindle motor applied to Lathes, Mills, Car Hoists, Pumps & Conveyors, etc. Used for engraving machine or used with frequency converter..
Output Current: 5A. The machine is screwed to ensure the safety and reliability of the use. DC cooling fan low noise, large air volume.The converter has overload protection, overvoltage protection overheat protection etc..
✅75W 110V Water Pump：Power: 75W, Flow: 3000L/H, Hmax: 3.5M, Voltage: 110V/60HZ, Size: L4.8xW3.5xH4.3 in. This is a high-performance, energy-efficient pump and is well-designed for use in spindle, suitable for 0.8KW, 1.5KW, 2.2KW, 3KW and other high speed CNC water cooled spindle motor.ps: the submersible pump should be completely immersed in water when it is working ..
✅Support：We offer 1 year warranty. If you get stuck, contact us with any questions that arise, our customer service team are waiting for helping you within 24 hours and we promise we will provide a 100% satisfied solution for you!.

Application: Spindle Motor, Drill Press, CNC, HVAC, Lathe, Milling, Pumps, Conveyors, Mach3, Fan, Cooling, Compressor, Three-phase motor and other machines!.
Spacing 2.54mm bar connector, 5-pin plug. DC cooling fan low noise, large air volume..
The machine is screwed to ensure the safety and reliability of the use. Three anti-paint protection lines, improve and extend the life of the fuselage..
The operator panel can be moved out and extended by 2M, 1.5M, 1M, 30CM. 1 Year replace or refund!!!.

The AD8302 is a fully integrated system for measuring gain/loss and phase in numerous receive, transmit, and instrumentation applications. It requires few external components and a single supply of 2.7 V–5.5 V. The ac-coupled input signals can range from –60 dBm to 0 dBm in a 50 ohm system, from low frequencies up to 2.7 GHz. Both subsystems have an output bandwidth of 30 MHz, which may optionally be reduced by the addition of external filter capacitors. 003cbr003e.
The AD8302 can be used in controller mode to force the gain and phase of a signal chain toward predetermined setpoints.003cbr003e.
The AD8302 includes a phase detector of the multiplier type, but with precise phase balance driven by the fully limited signals appearing at the outputs of the two logarithmic amplifiers. Thus, the phase accuracy measurement is independent of signal level over a wide range. The signal inputs are single-ended, allowing them to be matched and connected directly to a directional coupler. Their input impedance is nominally 3 kΩ at low frequencies. 003cbr003e.
The phase and gain output voltages are simultaneously available at loadable ground referenced outputs over the standard output range of 0 V to 1.8 V. The output drivers can source or sink up to 8 mA. A load....