Reviews Arduino Project Case

Geekworm UNO R3 Case | Protective Enclosure ABS Computer Box for Arduino UNO R3/UNO WiFi REV2/UNO REV3- Transparent

This Geekworm design ABS tranparent case is perfect compatible with Arduino UNO R3 development board, UNO WiFi REV2 or UNO REV3. (Arduino UNO Case).
Case Size: 7.5cm x 6cm x 2cm (2.95inch x 2.36inch x 0.78inch).
It is design with two nice "+" holes and 10 "-" holes for cooling system..
It is very easy to install and Mini & attractive body to carry everywhere..
Note: The UNO R3 board is not included in the packing list..
Packing List: 1x UNO R3 ABS Case-Transparent.

A plug 'n' play shield for experimenting with monitoring fleets, high-altitude measurements, or any kind of project requiring localization of devices..
Arduino MKR GPS Shield uses the u-blox SAM-M8Q GNSS (Global Navigation Satellite System) module. It is meant to be used on top of boards in the Arduino MKR boards, but thanks to its Eslov connector, it is also possible to hook it up to any board..
It comes with a dedicated library that allows two different interfaces and offers a consistent set of APIs designed for a full usage of the GPS acquired information..
Operating voltage is 3.3V, but this shield comes also with an on-board holder for CR1216 batteries..
The MKR GPS Shield has an additional connector meant as an extension of the I2C bus. The extra I2C port, also referred to as the Eslov self-identification port comes with: SDA, SCL, GND, +5V, and an extra digital pin, meant to send an alarm to the otherwise plain I2C devices connected to it..

Type: 9V T Type Battery Snap Connector, to power anything that running with a 9V battery..
Use: Can be conveniently connected to other power module or Arduino board..
Cable: Approx. 15cm (6 inch) length, red wire for positive, black wire for negative, easy to connect or solder to other equipment..
Application: Can be used for power supply or other 9V battery equipment, supplying power sourcec for Arduino Project or LED Light Bar etc. portable, easy to use..
Package: 6pcs 9V T Type Battery Snap Connector Clip Lead Wire (NO battery included).

The pitch of each end of the wire is 0.1 inch (2.54mm).
40 pin jumper Wire are easy to separate from the ribbon.
Suitable for Arduino breadboard kit project, PCB project, PC motherboard, DIY experiment, 3D printer and etc..
Package content: 1 * 40 pin male to female jumper wires, 1 * 40 pin male to male cable and 1 * 40-pin female to female cable (total 120pcs)Description.
The wires are easy to peel apart and great for making good looking prototypes.
Work on a Raspberry pi breadboard projects, Raspberry pi robot build, Breadboard prototyping, Arduino and ky-040 rotary encoders..
Insert onto the SW LED pin on the typical desktop computer mother board..
Test bread boarding projects or for any breadboard experimenter..
1 * 11.8 inch 40 pin male to male Breadboard Jumper Wires.
1 * 11.8 inch 40 pin female to female Breadboard Jumper Wires.
1 * 11.8 inch 40 pin male to female Breadboard Jumper Wires.

✔️3220 Solderless Breadboard plus Electronics fun kit,Compatible with Arduino and Raspberry Pi.
✔️Power Supply Module,Include a good range of LEDs, resistors, buttons, capacitors, a few transistors and diodes..
✔️140 pcs U-shape Solide Copper Jumper Wires plus 65 PCS Copper Jumpers Meet your project expetation.
✔️Better improvement on product quality and durablity.
✔️Perfect for Arduino/Raspberry Shield Prototyping and Testing. Powered by Makeronics Technology.

✔️1660 Solderless Breadboard plus Electronics fun kit,Compatible with Arduino and Raspberry Pi.
✔️A Breadboard and Power Supply Module -Include a good range of LEDs, resistors, buttons, capacitors, a few transistors and diodes..
✔️140 pcs U-shape Solide Copper Jumper Wires plus 65 PCS Copper Jumpers Meet your project expetation。.
✔️Better improvement on product quality and durablity.
✔️Perfect for Arduino Shield Prototyping and Testing. Powered by Makeronics Technology.

This is a control board with built-in Ethernet function, like a hybrid of an Arduino Uno R3 and an Ethernet/micro sd shield..
MAC addresses are not unique, you can set MAC address in the code. It comes with a microUSB port instead of the standard Arduino one..
TF card can’t be connected to control board when reading IP address code, otherwise, IP address might be not read Code..
The SD card slot is push release and sturdy. The ethernet port extends beyond the PCB which is nice for panel mounting in a project box..
Search for "keyestudio wiki KS0304" in Google Chrome to get the online tutorial. Note that the code and libraries we provide are based on the 1.0.4 version of IDE, they may not be compatible with other versions..

Type: 9V T Type Battery Snap Connector, to power anything that running with a 9V battery..
Use: Can be conveniently connected to other power module or Arduino board..
Cable: Approx. 15cm (6 inch) length, red wire for positive, black wire for negative, easy to connect or solder to other equipment..
Application: Can be used for power supply or other 9V battery equipment, supplying power sourcec for Arduino Project or LED Light Bar etc. portable, easy to use..
Package: 6pcs 9V T Type Battery Snap Connector Clip Lead Wire (NO battery included).

This RAB plate holder is widely compatible with not only Raspberry Pi 4 Model B, Raspberry Pi 3B+/3B/2B/B+ but also Arduino Uno, Mega2560, also support both 400 points breadboard and 830 points breadboard..
Access to all consumer ports: TF cards, HDMI and USB cords, very convenient for your DIY porjects.
Portable, easy to move, carry, this RAB holder is stable to fixed on the table for your needs..
Excellent Tool in education and DIY project for Raspberry Pi and Arduino UNO Mega 2560..
Wiki for reference: raspberrypiwiki.com/RAB_Holder.