Reviews Aluminum Intercooler

FMIC Intercooler Kit For 02-05 Audi A4 B6 1.8T

CXRacing Aluminum Y Pipe, Dual 3" to Single 4", For Air Intake or Intercooler Piping.

The 300-620 top-feed plenum entry configuration is designed to allow the included Hi-Ram 105mm plenum top to be fitted to a low-profile base intake manifold. The short runner, low-profile base intake manifold intended for forced induction applications was conceived to package with an air to water plenum mounted intercooler with a shorter overall height than possible with other existing intake manifolds..
The Holley LS1/2/6 Lo-Ram intake manifold kits are designed for GM LS Gen III & IV engines equipped with GM LS1/2/6 (cathedral port) cylinder heads. These intake manifolds will work with OE or aftermarket cylinder heads. The fuel rail kits come with 2 sets of brackets: A set for long (usually standard length) fuel injectors & set for short (such as Pico, or LS7) fuel injectors..
NOTE: Total Height: Top-Feed Plenum Configuration w/105mm Long. Mount EFI Plenum Top - 9.07" (without intercooler installed) | Top-Feed Plenum Configuration w/105mm Long. Mount EFI Plenum Top, w/ intercooler installed - 9.07" + intercooler thickness.
Specs: Brand: Holley EFI | Color: Black | Construction: Cast | Emission Code: 3 | Engine: GM LS1/LS2/LS6 | Finish: Black | Flange Style: EFI | Front Height: 9.07" without Intercooler | Fuel | System Type: EFI | Manifold Type: Lo....

Ideal replacement - this intercooler hose matches the fit and function of the original equipment hose.
Greater durability - this intercooler hose ends are made of stainless steel instead of the original equipment plastic to better withstand high temperatures.
Complete repair solution - this intercooler hose includes new end clamps required to complete installation.
Quality tested - this part has undergone try-on and material testing to ensure a quality fit and long service life.
Ensure fit - to make sure this part fits your exact vehicle, input your make, model and trim level into the garage tool.

compatible with Ford Focus ST 2013, 2014, 2015, 2016, 2017, 2018.
Larger Intercooler Provides More Efficient Cooling Power Equals More Power.
With Wind Deflector To Tunnel Air Into The intercooler.
Instant Horsepower And Torque Gain By Replacing Factory Intercooler.
Included Hardware For Direct Bolt On Installation.
No Install Instructions, Install Perform By Experienced Professional Installer Is Recommended..

This vise-mounted tool will form a perfect bead on the end of aluminium or copper tubing. Simply insert the end of the tubing between the dies and start cranking the turning handle. Give the wheel a quarter-turn with each full rotation of the tubing to gradually tighten the dies against the tubing..
Aluminum, steel or stainless steel Intake pipe -Aluminum, steel or stainless steel Intercooler pipe.
This his sturdy and cost effective tool makes it easy to add a professional looking bead to all types of tubing. Great for Aluminum up to 16 gauge wall thickness (0.065’’ or 1.65mm) and also suitable for Titanium up to 18 gauge (0.049’’ or 1.25mm)..

Perfect for 4/6 cylinder 1.5L-2.5L engines. Up to 400HP. Power performance output capability = 25-35 psi. CNC machined flanges..
1 x Turbo Oil Return / Feeding Line Kit: Stainless steel braided, it helps circulate oil from the turbo charger to the oil pan.
1 x Intercooler : Size 27” x 7” x 2.5” inch. Inlet size is 2.5 inch. Intercooler core size: 21*7*2.5 . Support up to 350 hp for this small intercooler size – tube and fin style ..
balancing Test by TURBOTECHNICS VSR3. G3-min-Flow VNT Turbo testing. Advanced Actuator Tester/Programmer.
Need modifications – Professionals ONLY (This is an aftermarket universal turbo kit for DIY purpose, and it’s recommended to advanced players but not for beginners. ).

Simply insert the end of the tubing between the dies and start cranking the turning handle.This vise-mounted tool will form a perfect bead on the end of aluminium or copper tubing..
Aluminum, steel or stainless steel Intercooler pipe Fits 5/8″ and larger tubing..
Aluminum pipe: diameter from 5/8″(16mm) to 4″(102mm),max thickness 3mm.
Steel pipe: diameter from 5/8″(16mm) to 4″(102mm),max thickness 1mm.
By turning the handle on the side of the tubing beader tool, you can form a desired bead on the end of aluminium or copper tubing..
Works best when secured in a vice.Please Note: Always apply the bead before welding..

OEM quality cast exhaust manifolds and downpipes.
Mandrel bent TIG welded aluminum intake piping.
Bar and plate front mount intercooler with brackets.
Complete braided SS -AN oil lines w/feed adapter All vacuum lines, pcv system, check valves, clamps, etc etc etc included.