Reviews Accelerator Dbd

Tram 140MHz-170MHz + 430MHz-470MHz Dual Band NMO Antenna (1181)

• Solid brass nmo mount with Black kote finish.

Tram 144mhz/440mhz Dual Band Pre Tuned Amateur Glass-Mount Antenna 1191

• NMO 3 1/4" Black Zinc Antenna Magnet mount.

Sirio Antenna GPS 27 1/2 10m & CB Base Antenna

• Base station antenna, omnidirectional tunable by acting on the whip length low radiation angle.
• Gain: 1/2: 0 dBd, 2.15 dBi bandwidth at S.W.R. 2:1.

Tram 1486 UHF Land Mobile Base Antenna

Browning 450MHz-470MHz UHF 3dBd Land Mobile NMO Antenna

Browning 380MHz-520MHz 2.4dBd Gain Land Mobile NMO Antenna

• Browning BR-450 UHF land mobile base antenna.

Dixell 9 Drive 9 Mode Electronic Throttle Controller Pedal Accelerator Booster For CHEVROLET DODGE FIAT HUMMER HOLDEN JEEP OPEL VAUXHALL, KA-809 Connector

• ...onnector before you order,if you have any issue,please contact me first,tell me your vehicle model and year,we can check and confirm for you,i do this,only hope you can receive the right item,any question,please contact me..
• Installation Step: firstly: find out the vehicle accelerator pedal secondly: unplug the vehicle accelerator pedal interface third: connect the throttle controller with accelerator pedal interface forth: stick the throttle controller on the place near to the dashboard.
• Installation points: 1. Turn off the flame and wait for 5 minutes 2. Unplug the original car's accelerator pedal interface 3. Connect the two interfaces of the controller to the ECU and the pedal throttle respectively. 4. Make sure the cable connection is secure and does not hinder driving 5. Stick the electronic display to a convenient location..
• Accelerator self-learning steps: 1. Connect the line when the car is powered off, then energize the car but do not start. 2. Press and hold the MODE button to enter the setting 8xx mode, then adjust to 800 by adding and subtracting buttons. 3. After the screen displays 800, then use the foot....

GY-521 MPU-6050 MPU6050 Module, 3 Axis Accelerometer 6 DOF Gyroscope Sensor Module Kit 16 Bit Converter Data Output IIC 3-5v Compatible with Arduino (10 Pieces)

• GY-521 MPU-6050 module: integrates 3-axis gyroscope and 3-axis accelerator, including the hardware accelerator engine for devices connected to the second I2C port, like another accelerator of other brands, magnetometer, or Digital Motion Processor (DMP) of other sensors.
• Parameter range: the MPU-6050's angular velocity range is ±250, ±500, ±1000 and ±2000°/sec (dps) for accurate fast and slow motion, and user-programmable accelerator full-frame sensing the range is ±2g, ±4g±8g and ±16g.
• Transmission can pass I2C up to 400kHz or SPI up to 20MHz.
• Chip built-in: with three 16-bit analog-to-digital converters (ADCs) for digitizing the gyroscope outputs and another three ones for digitizing the accelerometer outputs.
• Easy to use: the measured values of the sensor can be interrogated by the I2C interface.
• The accelerometer can be operated at both 3.3V and 5V.
• Compatible with Arduino and Raspberry Pi.
• Universal usable: the sensor can be applied to develop various entertaining applications and systems.
• Nice for projects with gaming and virtual reality devices, navigation (for drones and RC planes) and DIY robots.

Sirio Antenna Tornado27 Sirio Tunable 10M & Cb Base Antenna

• Base station antenna omnidirectional high power handling capability whip equipped whit waterproof jointing sleeve made of aluminum alloy.
• Type: 5/8 λ ground plane frequency range: tunable form 27 to 30 MHz impedance: 50Ω radiation (h-plane): 360° omnidirectional polarization.
• Gain: 1.2 DBD, 3.35 DBI bandwidth @ SWR ≤ 2: ≥ 1300 kHz SWR @ res, freq.: ≤ 1.2 @ 27 MHz.