Reviews 480 Volt Motors

Bergen Industries Inc PS613163 3-Wire Appliance and Power Tool Cord, 6 ft, 16 AWG, 13A/125V AC, 1625w,Black

For use with MAJOR APPLIANCES, MOTORS and POWER TOOLS, U-Ground NEMA 5-15.
APPLICATION: SJTW: Hard SERVICE cord, THERMOPLASTIC/Vinyl constructed JACKET, 300 Volt, WEATHER RESISTANT for OUTDOOR USE.
IDEAL FOR appliances, motors and power tools.
APPLICATION: 6 Foot 16/3 cord with U Ground NEMA 5-15 plug and pigtail end.
APPLICATION: Rated For: 13 Amp, 125V, 1625 Watts max applications.

Small size, high efficiency, low current (low cost switching power supply supporting).
to achieve a small size perfect combination of high flow.
Silent and vibrationless operation. Stainless steel shaft, completely submersible, rust and corrosion protection, need a separate float switch.
hose barb discharge outlet:1-1/8 inch (29millimeter).
Heavy duty motors, offer high capacity output Water cooled long-life motors.
Ignition protection Water/moisture tight seals.
Snap lock strainer base for easy installation and removal.

Our 24 volt 100 watt electric motor works just as well on a 12 volt system. No problems, no issues..
The 9 tooth #25 chain sprocket is a happy medium of torque and acceleration..
This fine little electric motor offers a range of compatibility including scooters from Pulse, Razor, and others..
You can control the left or right rotation by reversing the wires. This is especially useful for those garage projects using a pair of electric motors..

... simply as a DC 100 amp circuit breaker. This is a 12-48 volt DC (Direct Current) fuse breaker & CANNOT be used IN ANY AC (Alternate Current) OR HOUSEHOLD APPLICATION..
Be sure to consult your owner's manual when being used for your trolling motor plug and receptacle. Typically a 100 amp fuse is used on 12V trolling motors with 30, 40, or 45 lbs of thrust, 24V trolling motors with 70 lbs of thrust, & 36V trolling motors with no more than 100 lbs of thrust. A pair of 6 AWG copper lugs are included in this kit, but please verify that a AWG gauge trolling motor wire will be thick enough to handle your specific volt trolling motor plug..
Always consult a 12-48V DC wiring specialist if you are unsure about how to determine what type (this is a DC), amp (this is a 100A), and volt circuit breaker you require for your vehicle & vehicle accessories. A 1-300 amp circuit tester can be used to determine the draw of an accessory during initial, peak, and normal operation of the accessory, but this inline breaker is not a substitute for a sound professional installation. Always consult a professional before installation..

High Performance – Currie 36 Volt 30 Amp Controller with 5-pin Throttle Connection.
Compatible With – Schwinn S1000, S750, Ezip E1000 & Izip I1000 & i750 36 Volt Scooters.
Powerful High Amperage / Torque – 36 Volt Control Module with 5 Pin Throttle Connector.
Perfect Match Part – 600 Watt, 750 Watt, 900 Watt and 1000 Watt DC Brush Motors.
Waterproof, Low Voltage and Brake Inhibit – Under Voltage Protection (Low Voltage Cut-Off) and Optional Power Cut Off During Braking.

L298N as Main driver chip L298N, strong driving ability, strong anti-interference, low calorific value, afterflow diode protection, more stable and reliable for Arduino projects, Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability..
Double H bridge design, can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors, high efficient, To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage..
Driving DC motor Because the module is drived by double H bridge,it can drive two motors simultaneously.Input the following driving timing from IN1-IN4 then the speed and direction of the stepper motor can be controlled..
Easy to Use No assembly required. This L298N board comes ready to go. Just wire up motors and power, easy to use..
Wide Usage Great for DIY Smart Car Robot Power MEGA R3 for Mega2560 Duemilanove, if driving voltage is more than 12V, use external standard 5volt TTL outputs to switch the H-bridge circuits..