Reviews 12 layer Hasl Pcb

CZH-LABS DIN Rail Mount 8 Amp Solid State Relay SSR Module in 4~32VDC Out 100~240VAC 8 Channels

MOC3043 Phototriac and BTA12-600B triac (the heatsink is electrically insulated)..
Input Action Voltage DC 3 to 32V. LED indication for each channel. Anti-reverse protection diode..
Output Load Voltage range AC 100 to 240V (50/60Hz). Maximum on-state average current: 8 Amp, maximum on-state current 12 Amp (< 10 seconds). Isolation: Phototriac. Zero cross: Yes..
Terminal Block: Wire range: 24 ~ 12 AWG / 2.5mm square. Strip length: 7mm. Screws - M2.5, steel, Cr3+ Zn plated. Pin header and Cage - Brass..
DIN rail mount, Taiwan DINKLE fireproof nylon material DIN rail mount carrier (not China low quality carrier), can support width 35mm / 32mm / 15mm rail. FR-4 fiber glass PCB, dual copper layers..

Support AC and DC control signal, Relay action LED indicator, relay coil protection by means of a freewheeling diode..
Panasonic PA1a SPST-NO 5Amp power relay. Original Panasonic PA1a-PS pluggable socket for support replacement relay, and with removal key..
Dinkle high quality fireproof nylon material DIN rail mount housing, can support width 35mm, 32mm and 15mm rail..
High quality screw terminal blocks and clear marking label for terminal block position. Pitch 5.08mm/0.2" and 7.62mm/0.3" screw terminal block. Wire range 26 to 12AWG / 2.5mm square. Screws - M2.5, steel, Cr3+ Zn plated. Pin header and Cage - Brass..
High quality glass fiber FR-4 PCB, top and bottom dual copper layers..

【Dimension】 -Size：200mmx150mm/7.87"x5.91"(L*W).
【Material】 -The copper clad laminate is made of FR-4 glass fiber and copper, the number of layers issingle-sided.
【Features】- The copper clad board is resistant to high temperature, is not easily oxidized, is not easily deformed, and is convenient for welding.
【Application】 - PCB circuit boards are very suitable for making PCB circuit boards and models. It is widely used in product development, DIY experiment, maintenance, production, etc.
【Noted】 -The product may be slightly scratched or dirty during transportation, which will not affect its use.

...e to stand up to 4A current and 0 - 24V (5V, 12V, 24V) voltage, the heat resistance level is -20℃ - 100℃, so they are suitable for most non-waterproof 4 pin SMD 5050 RGB lights in 0.39 inch/ 10 mm width.
Note: you should pay attention to use them correctly for ensuring safety and extending service life.
Cuttable PCB board: the PCB board is cuttable, so you can use a cutting tool to cut T-shaped, L-shaped and X-shaped PCB board into any shape you want to facilitate the connection of various forms of light strips.
Just use your imagination to DIY a special light strip.
Please cut the LED strip according to the cuttable mark when you want to change the shape of PCB board.
Simple to install: the LED strip connector clip can be easily opened and closed, you can quickly slide RGB strip into the connector clip without any tool, please make sure connector + - polarity in line with + of strip before you connect it.
Wide range of usages: the 5050 LED strip connectors are suitable for standard density strips or DIY LED lights, for corner connection, and able to decorate Christmas trees, parties, birthdays, weddings, parties and other scenes according to your own needs.
Sufficient quantity: the package comes with 40 pieces 4 pin LED connectors, 15 pieces L-shape....

250pcs standoffs are made of durable environmentally friendly nylon PA66, which has stable and long-lasting acid resistance, alkali resistance, insulation and signal interference resistance..
The waterproof nylon spacer support is rust-proof and easy to clean. You only need to clean it with a cloth..
There are 4 different kits to meet your building needs, including various male or female brackets, nuts and screws..
Threaded standoff is very suitable for installation between the PCB circuit board and the machine board. It is very suitable for creating hot channels between chips, or creating multi-layer and multi-layer "nerd" homemade circuit board arrays..
They are not easy to slip when used correctly. It is very suitable for installing boards between PCB circuit boards and machines, and is widely used in communications, electroplating, medical equipment, office equipment, electronic products and other industries..

Consists of 20 static colors, 8 dynamic modes and 6 DIY colors.
Consists of individual 5050 LED emitters on 2 rolls of 25ft led strips.
Double side sticky adhesive allows for quick and easy installation in a wide variety of locations.
Safe to touch under 12 volt working voltage.
double copper layers on pcb board makes the lights stronger.

【FUNCTION】It is a new project to update the keyboard by filling the gap between the switch and the pcb, reducing vibrations and typing sounds..
【CHARACTERISTICS】We customize the bottom of the material has a layer of film plus non-stick adhesive backing will be more resistant to tearing, support repeatedly tear off and then stick on..
【SET MATCHING】You can place the Keyboard switch pads directly on the PCB with tweezers without disassembling the keyboard..
【MATERIAL】Made of 0.5mm thick Poron high-density memory foam..
【PACKAGE INCLUDES】Keyboard switch pads*120 x 1 , Tweezers x 1..